Planet WGs-4215-8HP2S User manual

Industrial Wall-mount Managed
Gigabit Ethernet Switch
WGS-4215-8HP2S
Quick Installation Guide

Table of Contents
1. Package Contents ....................................................................................... 3
2. Requirements ............................................................................................. 4
3. Hardware Installation .................................................................................. 5
3.1 Wall Mount Installation......................................................................... 5
3.2 Wall Hanging Installation...................................................................... 6
4. Wiring the Power Inputs.............................................................................. 8
4.1 Terminal Block Connector Pinout ........................................................... 8
4.2 Wiring Completed in Three Steps.......................................................... 9
5. Web Login.................................................................................................10
5.1 Starting Web Management ..................................................................10
 5.2 SavingCongurationviatheWeb ........................................................12
6. SSH Login.................................................................................................13
 6.1 ConguringIPAddress........................................................................13
 6.2 StoringtheCurrentSwitchConguration ..............................................14
7. RecoveringBacktoDefaultConguration.....................................................15
8. Customer Support .....................................................................................16

3
1. Package Contents
Thank you for purchasing PLANET Industrial Wall-mount Managed Gigabit Switch,
WGS-4215-8HP2S.Thetablebelowshowsthemodelwiththenumberofports:
ModelName Copper Port Fiber Port
WGS-4215-8HP2S 8 x 10/100/1000T 2 x 100/1000X
In the following sections, unless specied, the term “Wall-mount Managed
Switch” mentioned in this quick installation guide refers to the above model.
Open the box of the Wall-mount Managed Switch and carefully unpack it. The box
shouldcontainthefollowingitems:
TheWall-mountManagedSwitchx1 QuickInstallationGuidex1pc
Wall-mountedKitx1set RJ45 Dust Cap x 8 SFP Dust Cap x 2
If any item is found missing or damaged, please contact your local reseller for
replacement.

4
2. Requirements
zAat-bladescrewdriver
zWorkstationsrunningWindowsXP/2003/Vista/7/8/2008/10,MAC OSXor later,
Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPprotocols.
zWorkstations are installed with Ethernet NIC(NetworkInterfaceCard)
zEthernet Port Connection
Networkcables--Usenetwork(UTP)cableswithRJ45connectors.
The workstation is installed with Web browser.
The above Workstations have been installed with SSH and telnet client soft-
ware,suchasTeraTermorPuTTY.
Note
It is recommended to use Internet Explorer 8.0 or above to access
the Wall-mount Managed Switch. If the Web interface of the Wall-
mount Managed Switch is not accessible, please turn off the anti-
virus software or firewall and then try it again.

5
3. Hardware Installation
3.1 Wall Mount Installation
To install the Wall-mount Managed Switch on the wall, simply follow the following
steps:
Step 1: Drill 4 holes with 8mm diameter on the wall. The horizontal and vertical
distances between the 2 holes are 230mm and 124mm,respectively.
230mm
124mm
Ø4mm
6mm
Ø8mm
Step 2: Hammer the four anchors into the four holes.
Step 3: Then the four given screws are screwed into the anchors to nish the
wall-mountinstallation,asshownbelow.
ACTLNK
ACTLNK
1G/2.5G
100
1000 LNK/ACT
10/100 LNK/ACT
bt PoE-in-Use
at PoE-in-Use
R.O.
Ring
PWR 2
PWR 1
SFP
9
10
PWR 1
V1
V1+
PWR 2
V2
V2+
3 421 7 865
WGS-5225-8UP2SV
Managed
Fiber
SFP
910
Alarm
Smart LCD
DC Input Range
48-54V
, 8A max.
PoE++
Dual power input is required
for maximum PoE loading.
Max. Fault Alarm Loading: 24V,1A
1000 LNK/ACT
10/100 LNK/ACT
bt PoE-in-Use
at PoE-in-Use
3 421
PoE++
1000 LNK/ACT
10/100 LNK/ACT
7 865
PoE+
V+
Ground
SFP
910
ACTLNK
ACTLNK
1000
100
120W
240W
360W
PWR
SFP
9
10
PoE Usage
DC Input Range
48-54V
, 8A max.
WGS-4215-8HP2S
Managed
Fiber
PoE++
at PoE-in-Use
230mm
124mm

6
3.2 Wall Hanging Installation
To hang the Wall-mount Managed Switch on the wall, simply follow the following
steps:
Step 1: Drill 2 holes (one hole on each side) with 8mm diameter on the wall; the
distance between the 2 holes is 230 mm and the line through them must
be horizontal.
1 2
Step 2: Place two anchors inside the hole by hammering them. Then screw the
two screws leaving a space of 2mm apart as shown in the circled diagram
below.
ACTLNK
ACTLNK
1G/2.5G
100
1000 LNK/ACT
10/100 LNK/ACT
bt PoE-in-Use
at PoE-in-Use
R.O.
Ring
PWR 2
PWR 1
SFP
9
10
PWR 1
V1
V1+
PWR 2
V2
V2+
3 421 7 865
WGS-5225-8UP2SV
Managed
Fiber
SFP
910
Alarm
Smart LCD
DC Input Range
48-54V
, 8A max.
PoE++
Dual power input is required
for maximum PoE loading.
Max. Fault Alarm Loading: 24V,1A
1000 LNK/ACT
10/100 LNK/ACT
bt PoE-in-Use
at PoE-in-Use
3 421
PoE++
1000 LNK/ACT
10/100 LNK/ACT
7 865
PoE+
V+
Ground
SFP
910
ACTLNK
ACTLNK
1000
100
120W
240W
360W
PWR
SFP
9
10
PoE Usage
DC Input Range
48-54V
, 8A max.
WGS-4215-8HP2S
Managed
Fiber
PoE++
at PoE-in-Use
2mm
4mm Screw

7
Step 3: Theswitch,showninthepicturebelow,cannowbehungonthewall.
ACTLNK
ACTLNK
1G/2.5G
100
1000 LNK/ACT
10/100 LNK/ACT
bt PoE-in-Use
at PoE-in-Use
R.O.
Ring
PWR 2
PWR 1
SFP
9
10
PWR 1
V1
V1+
PWR 2
V2
V2+
3 421 7 865
WGS-5225-8UP2SV
Managed
Fiber
SFP
910
Alarm
Smart LCD
DC Input Range
48-54V
, 8A max.
PoE++
Dual power input is required
for maximum PoE loading.
Max. Fault Alarm Loading: 24V,1A
1000 LNK/ACT
10/100 LNK/ACT
bt PoE-in-Use
at PoE-in-Use
3 421
PoE++
1000 LNK/ACT
10/100 LNK/ACT
7 865
PoE+
V+
Ground
SFP
910
ACTLNK
ACTLNK
1000
100
120W
240W
360W
PWR
SFP
9
10
PoE Usage
DC Input Range
48-54V
, 8A max.
WGS-4215-8HP2S
Managed
Fiber
PoE++
at PoE-in-Use
1Place against a wall
2Hang up
4mm Screw
Caution
Makesure theequipmentis securely wall-mountedas strongvibra-
tion could cause it to drop or break.

8
4. Wiring the Power Inputs
The Wall-mount Managed Switch features a strong and convenient power input
system incorporated into customer’s automation network to enhance system
uptime.
Model Power Input Range PWR
WGS-4215-8HP2S DC48-54V,8Amax
Note: Maximum power requirements also rely on the real site application.
1000 LNK/ACT
10/100 LNK/ACT
bt PoE-in-Use
at PoE-in-Use
3 421
PoE++
1000 LNK/ACT
10/100 LNK/ACT
7 865
PoE+
V+
Ground
SFP
9 10
ACTLNK
ACTLNK
1000
100
120W
240W
360W
PWR
SFP
9
10
PoE Usage
DC Input Range
48-54V
, 8A max.
WGS-4215-8HP2S
ManagedFiberPoE++
at PoE-in-Use
10/100/1000BASE-T 802.3at PoE
+
RJ45 Port
10/100/1000BASE-T 802.3bt PoE++ RJ45 Port
3-pin Spring Terminal Block
V+
Ground
DC Input Range
48-54V
, 8A max.
4.1 Terminal Block Connector Pinout
TheFrontPaneloftheWall-mountManagedSwitchconsistsofoneterminal block
connector within 3 contacts. Please follow the steps below to insert the power
wire.
V+
Ground
Insertpositive/negativeDCpowerwiresintoContactsV+andV-forPower.

9
4.2 Wiring Completed in Three Steps
Step 1: Presstheat-bladescrewdriverdiagonallyintothereleasehole.
Step 2: Leave the at-blade screwdriver pressed into the release hole and insert
the wire into the terminal hole. Insert the wire until the stripped portion
is no longer visible to prevent shorting.
1
2
ACTLNK
ACTLNK
1G/2.5G
100
1000 LNK/ACT
10/100 LNK/ACT
btPoE-in-Use
atPoE-in-Use
R.O.
Ring
PWR 2
PWR 1
SFP
9
10
PWR 1
V1
V1+
PWR 2
V2
V2+
3 421 7 865
WGS-5225-8UP2SV
Managed
Fiber
SFP
910
Alarm
Smart LCD
DC Input Range
48-54V
, 8A max.
PoE++
Dual power input is required
for maximum PoE loading.
Max. FaultAlarm Loading: 24V, 1A
1000 LNK/ACT
10/100 LNK/ACT
btPoE-in-Use
atPoE-in-Use
3 421
PoE++
1000 LNK/ACT
10/100 LNK/ACT
7 865
PoE+
V+
Ground
SFP
910
ACTLNK
ACTLNK
1000
100
120W
240W
360W
PWR
SFP
9
10
PoE Usage
DC Input Range
48-54V
, 8A max.
WGS-4215-8HP2S
Managed
Fiber
PoE++
atPoE-in-Use
V+
Ground
DC Input Range
48-54V
, 8A max.
Wire
Flat-blade screwdriver
Step 3: Removetheat-bladescrewdriverfromthereleasehole.
 After you connect the wires, pull gently on the wire to make sure that it
willnotcomeoandthewireissecurelyfastenedtotheterminalblock.
3
ACTLNK
ACTLNK
1G/2.5G
100
1000 LNK/ACT
10/100 LNK/ACT
btPoE-in-Use
atPoE-in-Use
R.O.
Ring
PWR 2
PWR 1
SFP
9
10
PWR 1
V1
V1+
PWR 2
V2
V2+
3 421 7 865
WGS-5225-8UP2SV
Managed
Fiber
SFP
910
Alarm
Smart LCD
DC Input Range
48-54V
, 8A max.
PoE++
Dual power input is required
for maximum PoE loading.
Max. FaultAlarm Loading: 24V, 1A
1000 LNK/ACT
10/100 LNK/ACT
btPoE-in-Use
atPoE-in-Use
3 421
PoE++
1000 LNK/ACT
10/100 LNK/ACT
7 865
PoE+
V+
Ground
SFP
910
ACTLNK
ACTLNK
1000
100
120W
240W
360W
PWR
SFP
9
10
PoE Usage
DC Input Range
48-54V
, 8A max.
WGS-4215-8HP2S
Managed
Fiber
PoE++
atPoE-in-Use
V+
Ground
DC Input Range
48-54V
, 8A max.
Wire
Flat-blade screwdriver
Note
1.Thewiregaugeshouldbeintherangefrom12to16AWG.
2. The device must be grounded.

10
5. Web Login
5.1 Starting Web Management
The following shows how to start up the Web Management of the Wall-mount
Managed Switch. Note the Wall-mount Managed Switch is congured through an
Ethernet connection. Please make sure the manager PC must be set to the same
IP subnet address.
For example, the default IP address of the Wall-mount Managed Switch is
192.168.0.100, then the manager PC should be set to 192.168.0.x (where x
is a number between 1 and 254, except 100) and the default subnet mask is
255.255.255.0. PC / Workstation
with Web Browser
192.168.0.x
Managed Switch
RJ45/UTP Cable
IP Address: 192.168.0.100
Figure 5-1: IP Management Diagram
Logging in to the Wall-mount Managed Switch
1.Use Internet Explorer 8.0 or above Web browser and enter IP address
https://192.168.0.100 to access the Web interface.
2.When the following dialog box appears, please enter “admin” in both the
defaultusernameandpasswordelds.TheloginscreeninFigure5-2appears.
DefaultIPAddress:192.168.0.100
DefaultUsername:admin
DefaultPassword:admin
Figure 5-2: Web Login Screen