Planet WSD-800 User manual

Managed Ethernet Switches
WSD-800 / WGSD-910 / WGSD-1022C
WSW-2401A / WGSW-2840 / WGSW-5240
Quick Installation Guide

Table of Contents
1. Package Content.......................................................................................... 3
2. Terminal Setup ............................................................................................ 4
3. Logon to the Console ................................................................................... 5
4. Congure IP address.................................................................................... 7
5. Start Web Management................................................................................ 8

3
1. Package Content
Thank you for purchasing the Planet Layer 2 Managed Switch. In the following
section, the term “Switch” means the Layer 2 Managed Switch.
The PLANET Layer 2 Managed Switch comes with one of the following models.
● WSD-800: 8-Port 10/100Mbps Managed Ethernet Switch
● WGSD-910: 8-Port 10/100Mbps + 1 Gigabit TP/SFP Combo Managed Switch
● WGSD-1022C: 8-Port 10/100Mbps + 2 Gigabit TP/SFP combo Managed Switch
● WSW-2401A: 24-Port 10/100Mbps + 1 Fiber Slot Managed Switch
● WGSW-2840: 24-Port 10/100Mbps + 4G TP/SFP combo Managed Switch
● WGSW-5240: 48-Port 10/100Mbps + 4G TP/SFP Combo Managed Switch
Upon open the box of the Switch and carefully unpack it. The box should contain
the following items:
> The Switch x 1
> This Quick Installation Guide x 1
> User’s manual CD x 1
> Power Cord x 1
> RS-232 Cable x 1
> Rubber feet x 4
> Rack mount accessory x 1
If any item is found missing or damaged, please contact your local reseller
for replacement.

4
2. Terminal Setup
To congure the system, connect a serial cable to a COM port on a PC or notebook
computer and to serial (console) port of the Switch. The console port of the Switch
is DCE already, so that you can connect the console port directly through PC
without the need of Null Modem.
A terminal program is required to make the software connection to the Switch.
Windows’ Hyper Terminal program may be a good choice. It can be accessed
from the Start menu. Click START, then Programs, Accessories and then Hyper
Terminal.
MS-DOS based terminal program such as PC-PLUS, PROCOMM, can also make the
connection with the Switch. The COM port should be congured as:
□ Baud : 9600
□ Parity : None
□ Data bits : 8
□ Stop bits : 1
□ Flow Control : None

5
3. Logon to the Console
Once the hardware connection and the terminal program are ready, power on the
Switch. The terminal program will display the testing procedures of the Switch and
show in Figure 3-1.
Figure 3-1 Testing Procedure Screen of the Switch
After boot up is complete, the “switch>” prompt shows up. Enter “enable” for
further conguration. A prompt then shows up for password, please enter “admin”
to enter. As show in Figure 3-2.
Figure 3-2 Login in with Password

6
The prompt then change to the “switch\enable>”, please enter “?” to list the
commands it offers. As show in Figure 3-3.
Figure 3-3 List commands
Note
1. For security reason, please change and memorize the new pass-
word after this first setup.
2. Only accept password in lowercase letter under console inter-
face.

7
4. Congure IP address
The default IP address of the Switch is “192.168.0.100”. If you want to change
the IP address, for example, change the IP address to “192.168.99.234” with
subnet mask. “255.255.255.0”, please enter the
command:
set system ip 192.168.99.234 255.255.255.0
As show in Figure 4-1.
Figure 4-1 Set IP address
Now the IP address has changed to 192.168.99.234. The changed IP address will
remain the original after reboot unless you save the conguration. To do this, enter
“copy cong ash” to save the conguration. As show in Figure 4-2.
Figure 4-2 Save conguration

8
5. Start Web Management
The Switch can be fully managed by console. It also provides a convenient Web
management interface for remote management. This chapter guides the quick
access to the Web Management Interface of the Switch.
Since Web Management Interface can be accessed by Ethernet connection, the
administrator workstation must be in the same IP segment as the Switch.
For example, if you do not change the default IP address of the Switch, say
192.168.0.100, you must set the IP address of your administrator workstation to
be 192.168.0.x (where x is a number between 1 and 254, except 100) with subnet
mask is 255.255.255.0.
Then use the Internet browser (Internet Explorer 5.0 or above), and go to
http://192.168.0.100. Enter the default username “admin” default password
“admin” for login, and the main screen as gure 5-1 appears.
Default IP Address: 192.168.0.100
Default Username and Password: admin
Note
The following screen based on WGSW-2840, for other Layer 2
Management Switch that mentioned in chapter 1, the display will
be the same to WGSW-2840.
Figure 5-1 Web Main Screen of the Switch
You can either manage the Switch through the Web interface or through the
console. Please also refer to the user’s manual in the CD-ROM for more information
about the Switch and the management.