Planet SGSW-24040 User manual

24-Port 10/100/1000Mbps with
4 Shared SFP Managed Gigabit Switch
WGSW-24040 / SGSW-24040
Quick Installation Guide

Table of Contents
1. Package Content......................................................................................... 3
2. Requirements ............................................................................................. 4
3. Terminal Setup ........................................................................................... 5
4. Logon to the Console.................................................................................. 6
5. CongureIPaddress................................................................................... 7
ShowthecurrentIPaddress ....................................................................... 7
CongureIPaddress................................................................................... 8
6. Start Web Management............................................................................... 9
LogintheManagedSwitch........................................................................... 9
WhileIPAddressbechangedorforgottenadminpassword–.......................11
Customer Support .........................................................................................12

3
1. Package Content
Thank you for purchasing PLANET Layer 2 Managed Switch, WGSW-24040 /
WGSW-24040R / SGSW-24040 / SGSW-24040R. Terms of “Managed Switch”
means the Switches mentioned titled in the cover page of this Quick installation
guide,i.e.WGSW-24040/SGSW-24040.
Open the box of the Managed Switch and carefully unpack it. The box should
containthefollowingitems:
TheWGSW/SGSWManagedSwitchx1
User’s manual CD x 1
Quickinstallationguidex1
RS232 cable x 1
Rubberfeetx4
Tworack-mountingbracketswithattachmentscrewsx1
PowerCordx1
CB-STX50-50cmstackcablex1(SGSW-24040/24040Rolny)
If any item is found missing or damaged, please contact your local reseller for
replacement.
ó
ó
ó
ó
ó
ó
ó
ó

4
2. Requirements
Workstations of subscribers running Windows 98/ME, NT4.0, 2000/XP, MAC OS9
orlater,Linux,UNIXorotherplatformcompatiblewithTCP/IPprotocols.
WorkstationinstalledwithEthernetNIC(NetworkCard)
Serial Port connect(Terminal)
AbovePCwithCOMPort(DB-9)
Ethernet Port connect
>Networkcables-Usestandardnetwork(UTP)cableswithRJ45connectors.
>AbovePCinstalledwithWEBBrowserandJAVAruntimeenvironmentPlug-in
Note
It is recommended to use Internet Explore 6.0 or above to access
WGSW/SGSWManagedSwitch.
ó
ó
ó
ó
ó

5
3. Terminal Setup
To congure the system, connect a serial cable to a COM port on a PC or
notebook computer and to serial (console) port of the WGSW / SGSW Managed
Switch. The console port of the Managed Switch is DCE already, so that you can
connecttheconsoleportdirectlythroughPCwithouttheneedofNullModem.
A terminal program is required to make the software connection to the WGSW /
SGSW Managed Switch. Windows’ Hyper Terminal program may be a good choice.
TheHyperTerminalcanbeaccessedfromtheStartmenu.
1. Click START,thenPrograms,AccessoriesandthenHyper Terminal.
2.When the following screen appears, make sure that the COM port should be
conguredas:
Baud:115200
Parity:None
Databits:8
Stopbits:1
FlowControl:None
ó
ó
ó
ó
ó

6
4. Logon to the Console
Once the terminal has connected to the device, power on the WGSW / SGSW
ManagedSwitch,theterminalwilldisplaythatitisrunningtestingprocedures.
Then,thefollowingmessageaskstheloginpassword.Thefactorydefaultpassword
asfollowingandtheloginscreeninFigure4-1appears.
Password: admin
Figure 4-1 WGSW / SGSW Managed Switch Console Login screen
Note
1.Forsecurityreason,pleasechangeandmemorizethenewpass-
wordafterthisfirstsetup.
2. Only accept command in lowercase letter under console inter-
face.

7
5. Congure IP address
The WGSW / SGSW Managed Switch is shipped with default IP address as
following.
IPAddress:192.168.0.100
SubnetMask:255.255.255.0
TocheckthecurrentIPaddressormodifyanewIPaddressfortheSwitch,please
usetheproceduresasfollow:
Show the current IP address
1. On “Switch/>”prompt,enter“show ip”.
2.Thescreendisplays thecurrentIP address,SubnetMaskandGateway.Asshow
inFigure5-1.
Figure 5-1 Show IP information screen

8
Congure IP address
3. On “Switch/>” prompt, enter the following command and press <Enter>. As
showinFigure5-2.
Switch/>ipsetup192.168.1.100 255.255.255.0 192.168.1.1
ThepreviouscommandwouldapplythefollowsettingsfortheSwitch.
IP: 192.168.1.100
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.1
Figure 5-2 Set IP address screen
4.RepeatStep1tocheckiftheIPaddressischanged.
If the IP is successfully congured, the Managed Switch will apply the new IP
address setting immediately. You can access the Web interface of WGSW / SGSW
ManagedSwitchthroughthenewIPaddress.
Note
Ifyoudonotfamiliarwithconsolecommandortherelatedparam-
eter,enter“help”anytimeinconsoletogetthehelpdescription.

9
6. Start Web Management
The following shows how to start up the Web Management of the WGSW /
SGSW Managed Switch. Note the Managed Switch is congured through an
Ethernet connection, please make sure the manager PC must be set on the same
IP subnet address.
For example, the default IP address of the WGSW / SGSW Managed Switch is
192.168.0.100, then the manager PC should be set at 192.168.0.x (where x
is a number between 1 and 254, except 100), and the default subnet mask is
255.255.255.0.
Figure 6-1 IP Management diagram
Login the Managed Switch
1.Use Internet Explorer 6.0 or above Web browser, enter IP address
http://192.168.0.100 (the factory-default IP address or that you have just
changedinconsole)toaccesstheWebinterface.

10
2.When the following dialog box appears, please enter the default password
“admin” (or the password you have changed via console). The login screen in
Figure6-2appears.
DefaultPassword:admin
Figure 6-2 Login screen
3.Afterenteringthepassword,themainscreenappearsasFigure6-3.
Note
The following screen based on WGSW-24040 for SGSW-24040 the
displaywillbethesameforWGSW-24040.
Figure 6-3 Web Main Screen of WGSW / SGSW Managed Switch