Plumbline ECO STYLE ES1560 User manual

ES1560 ES2266 ES2083
WARRANTY:
WARNINGS
-The plumbing installation should be fitted with adequate water filters and pressure regulation devices in order to avoid misfunctioning in case of pressure shocks
-Advised pressure is between 3 and 5 bars
-Flush pipelines thoroughly before installing mixers
-Clean the mixers with soap mixed with water; products must be dried with a soft cloth in order to prevent limescale deposits
-Limescale deposits or other impurities in filters of flow guides must be removed monthly by using appropriate products or by immersing in water/vinegar solution (80/20)
-For each mixer installation, please follow instructions in corresponding page
97 mm
153 mm
116 mm
153 mm
100 mm
110 mm
140 mm
60 mm
100 mm
MAINTENANCE
- Unscrew dowel (2) using thespannersupplied (3).
- Unscrew cap (5)
- Unscrew theblocking nut (6) usingaspanner.
-. Replace cartridge (7).
- To remount theblocking nut (6) use a 0,8 Kgm max. dynamometricspanner to fasten.
- To remount the whole handle, follow the procedure reversed.
1
3
2
4
5
6
7
ARTICLES SPARE PARTS CODES
F81
ES1560
ARTICLES SPARE PARTS CODES
ES1560
ES2083
ES2266
K26
K25
-Unscrew the aerator with 22 mm spanner
-Immerse for half a day in the water-vinegar solution (80-20%)
-Wash, then reassemble
AERATOR MAINTENANCE
CARTRIDGE REPLACEMENT
T 04 568 9898 E [email protected] www.plumbline.co.nz
Distributed by:
INSTALLATION INSTRUCTIONS
ECO STYLE BASIN MIXER | ES1560
ECO STYLE SHOWER MIXER | ES2083
ECO STYLE DIVERTER MIXER | ES2266

NOTE
1
2
3
4
6
5
INSTALLATION
BASIN/BIDET MIXERS
ES1560
-Screw and tighten feed threaded tie rod (2)
-Insert gasket (3), then place the mixer on the basin/bidet/pillar/sink deck
-Insert gasket (4) and clamp (5)
-Tighten nut (6) using a 9 mm spanner
-Connect pipes (1) to water supply
-Install pop-up waste
-Remove handle.
-Remove cover plate (1).
-Unscrew diverter (2) .
-We recommend to replace the entire diverter unit and not separate
components
-Installing the concealed part of the mixer.
-Remove protecting cover and insert flange
-Install handle following the 'handle installation' instructions in the previous
page.
1
2
INSTALLATION
SHOWER/DIVERTER MIXERS
ES2083 / ES2266
ES2266 DIVERTER REPLACEMENT
Cold
Hot

NOTE
1
2
3
4
6
5
INSTALLATION
BASIN/BIDET MIXERS
ES1560
-Screw and tighten feed threaded tie rod (2)
-Insert gasket (3), then place the mixer on the basin/bidet/pillar/sink deck
-Insert gasket (4) and clamp (5)
-Tighten nut (6) using a 9 mm spanner
-Connect pipes (1) to water supply
-Install pop-up waste
-Remove handle.
-Remove cover plate (1).
-Unscrew diverter (2) .
-We recommend to replace the entire diverter unit and not separate
components
-Installing the concealed part of the mixer.
-Remove protecting cover and insert flange
-Install handle following the 'handle installation' instructions in the previous
page.
1
2
INSTALLATION
SHOWER/DIVERTER MIXERS
ES2083 / ES2266
ES2266 DIVERTER REPLACEMENT
Cold
Hot

ES1560 ES2266 ES2083
WARRANTY:
WARNINGS
-The plumbing installation should be fitted with adequate water filters and pressure regulation devices in order to avoid misfunctioning in case of pressure shocks
-Advised pressure is between 3 and 5 bars
-Flush pipelines thoroughly before installing mixers
-Clean the mixers with soap mixed with water; products must be dried with a soft cloth in order to prevent limescale deposits
-Limescale deposits or other impurities in filters of flow guides must be removed monthly by using appropriate products or by immersing in water/vinegar solution (80/20)
-For each mixer installation, please follow instructions in corresponding page
97 mm
153 mm
116 mm
153 mm
100 mm
110 mm
140 mm
60 mm
100 mm
MAINTENANCE
- Unscrew dowel (2) using thespannersupplied (3).
- Unscrew cap (5)
- Unscrew theblocking nut (6) usingaspanner.
-. Replace cartridge (7).
- To remount theblocking nut (6) use a 0,8 Kgm max. dynamometricspanner to fasten.
- To remount the whole handle, follow the procedure reversed.
1
3
2
4
5
6
7
ARTICLES SPARE PARTS CODES
F81
ES1560
ARTICLES SPARE PARTS CODES
ES1560
ES2083
ES2266
K26
K25
-Unscrew the aerator with 22 mm spanner
-Immerse for half a day in the water-vinegar solution (80-20%)
-Wash, then reassemble
AERATOR MAINTENANCE
CARTRIDGE REPLACEMENT