Plumbline progetto C1500 User manual

INSTALLATION INSTRUCTIONS
COMO FLOOR MOUNT BATH FILLER & HANDSHOWER
C1500
T 04 568 9898 E [email protected]
www.plumbline.co.nz
Distributed by:
IMPORTANT!
Please read these instructions prior to installation

RECOMMENDATIONS FOR INSTALLATION
Product performance cannot be guaranteed
if pressure is less than 1 bar. Above 5 bar a
pressure regulator must be installed. Failure to do
so voids the product warranty.
Water Pressure: 3 bar Water Temperature: 5°- 60°C
Always flush out the pipework before connecting
any tapware. Failure to do so voids the product
warranty.
Pre-Flush
ATTENTION: Failure to follow these recommendations may void the warranty.
It is recommended that a qualied, licensed tradesperson install this product.
Min 1
Max 5 3 Max 70°C 60°C
5°C

Clean with warm soapy water and a smooth
cloth. Avoid abrasive sponges or detergents as
these will damage the finish.
Cleaning
Remove the aerator with an aerator cartridge key.
Immerse for half a day in water-vinegar solution
(80-20%).
Wash, then reassemble.
Aerator Maintenance
CLEANING & MAINTENANCE
Before you start, turn off the water supply to the
mixer.
1. Remove the handle
2. Unscrew the dome (hand tightened)
3. Unscrew the locking nut
4. Remove the cartridge
Re-assemble in reverse order
Max tightening torque on locking nut: 10-12 Nm
Cartridge Replacement
1
2
3
4
For full details about our warranty visit
plumbline.co.nz/warranty-information
Warranty Information
Cartridge code: 35A

INSTALLATION INSTRUCTIONS
Prior to installation remove all parts from
the packaging and inspect for any transport
damage.
No. Name Qty
1 Mixer Body 1
2 Flange 1
3 Mounting Plate 1
4 Underfloor Mounting Box 1
5 Inlet Elbow 2
6 Handshower 1
7 Check Valve 1
8 Flow Regulator 1
9 Shower Hose 1
10 Instruction Manual 1
11 Fixing Kit 1

INSTALLATION INSTRUCTIONS
1Drill the holes for mounting the Underfloor
Mounting Box
The Underfloor Mounting Box must be recessed into the floor and levelled (using the spirit level provided)
as shown.
Mounting Box must be installed flush with, or just below, the finished floor level.
UNFINISHED FLOOR LEVEL
Underfloor Mounting Box
Finished
Floor Level
Spirit Level
IMPORTANT!
2Install the inlet elbows provided and screw
them into the Underfloor Mounting Box.
Set the Underfloor Mounting Box into the
recess in the floor and level using the spirit
level provided.
PTFE Tape Elbow

INSTALLATION INSTRUCTIONS
4Connect the hot & cold inlet pipes to the inlet
elbows.
5Complete the finished floor surface up to
the edge of the Underfloor Mounting Box,
ensuring that the the Underfloor Mounting
Box does not protude the finished floor level.
3Fix the Underfloor Mounting Box to the floor
with sleeve anchor bolts provided.
IMPORTANT!
Ensure it is fastened securely
Cold Water
Inlet
Hot Water
Inlet
UNFINISHED FLOOR LEVEL
FINISHED FLOOR LEVEL
6Remove the fixing plate, spirit level and blank
cover caps.

INSTALLATION INSTRUCTIONS
8Fit the fixing plate onto the mounting plate
(already attached to the Mixer Body in step 1).
9Align the copper pipes with the relevant hot
& cold connector holes on the Underfloor
Mounting Box. Fasten the fixing plate to the
Underfloor Mounting Box.
10 Fit the hose and handshower.
7Slide the flange over the bottom part of the
mixer body and attached the mounting plate
to the underside of the mixer body.

V 1.12.2022
DIVERTER OPERATION
Handshower On
Pull down on the outer sleeve and turn to lock.
Handshower Off
Turn sleeve and release, diverter will also return
to the original position when the mixer is closed.