Plumbline Progetto C1500 User manual

INSTALLATION INSTRUCTIONS
COMO FLOOR MOUNT BATH FILLER & HANDSHOWER
C1500
T 04 568 9898 E [email protected]
www.plumbline.co.nz
Distributed by:
IMPORTANT!
Please read these instructions prior to installation

RECOMMENDATIONS FOR INSTALLATION
Product performance cannot be guaranteed
if pressure is less than 1 bar. Above 4 bar a
pressure regulator must be installed. Failure to do
so voids the product warranty.
Water Pressure: 3 bar Water Temperature: 45°-65°C
Angle valves and/or lters are recommended to
prevent impurities and debris entering the mixer.
Stop Taps/Filters
Always ush out the pipework before connecting
any tapware. Failure to do so voids the product
warranty.
Pre-Flush
ATTENTION: Failure to follow these recommendations may void the warranty.
It is recommended that a qualied, licensed tradesperson install this product.
Min 1
Max 4 3 Max 70°C 60°C
45°C

Clean with warm soapy water and a smooth
cloth. Avoid abrasive sponges or detergents as
these will damage the finish.
Cleaning
Remove the aerator with an aerator cartridge key.
Immerse for half a day in water-vinegar solution
(80-20%).
Wash, then reassemble.
Aerator Maintenance
CLEANING & MAINTENANCE
Before you start, turn off the water supply to the
mixer.
1. Remove the handle
2. Unscrew the dome (hand tightened)
3. Unscrew the locking nut
4. Remove the cartridge
Re-assemble in reverse order
Max tightening torque on locking nut: 10-12 Nm
Cartridge Replacement
1
2
3
4
For full details about our warranty visit
plumbline.co.nz/warranty-information
Warranty Information

INSTALLATION INSTRUCTIONS
Prior to installation remove all parts from
the packaging and inspect for any transport
damage.
No. Name Qty
1 Mixer Body 1
2 Flange 1
3 Mounting Plate 1
4 Underoor Mounting Box 1
5 Inlet Elbow 2
6 Handshower 1
7 Check Valve 1
8 Flow Regulator 1
9 Shower Hose 1
10 Instruction Manual 1
11 Fixing Kit 1

INSTALLATION INSTRUCTIONS
1Slide the ange over the bottom part of the
mixer body and attached the mounting plate
to the underside of the mixer body.
2Drill the holes for mounting the Underoor
Mounting Box
The Underoor Mounting Box must be recessed into the oor and levelled (using the spirit level provided)
as shown.
Underoor Mounting Box
Finished
Floor Level
5mm
UNFINISHED FLOOR LEVEL

INSTALLATION INSTRUCTIONS
5Connect the hot & cold inlet pipes to the inlet
elbows.
Pressure test the whole unit before
sealing the oor to ensure there are no leaks.
6Complete the nished oor surface, ensuring
the oor surface is nished up to the edge of
the Underoor Mounting Box.
3Wrap PTFE tape on the inlet elbows provided
and screw them into the Underoor Mounting
Box.
Set the Underoor Mounting Box into the
recess in the oor and level using the spirit
level provided.
4Fix the Underoor Mounting Box to the oor
with toggle bolts provided.
PTFE Tape Elbow
Cold Water
Inlet
Hot Water
Inlet
UNFINISHED FLOOR LEVEL
FINISHED FLOOR LEVEL

INSTALLATION INSTRUCTIONS
8Fit the xing plate onto the mounting plate
(already attached to the Mixer Body in step 1).
9Align the copper pipes with the relevant hot
& cold connector holes on the Underoor
Mounting Box. Fasten the xing plate to the
Underoor Mounting Box.
10 A check valve is pre-installed in the
handshower. Connect ow regulator to the
handshower if necessary.
7Remove the xing plate, spirit level and blank
cover caps.

V 16.11.2020
DIVERTER OPERATION
Handshower On Handshower Off