Plumbline Progetto OLI316 User manual

INSTALLATION INSTRUCTIONS
OLI316 BASIN MIXER | OL003
OLI316 BIDET MIXER | OL018
OLI316 VESSEL BASIN MIXER | OL003H
OLI316 SHOWER MIXER | OL031
OLI316 DIVERTER MIXER | OL033
OLI316 BATH FILLER & H/SHOWER | OL077
OLI316 WALL MOUNT MIXER | OL005
!IMPORTANT!
Please read these instructions prior to installation
T04 568 9898 E[email protected]
www.plumbline.co.nz
Distributed by:

2
max 5
min 1
1 - 3
Water Pressure
1 - 3 bar
RECOMMENDATIONS FOR INSTALLATION
max 80
60
45 Water Temperature
45° - 65°C
Stop Taps
Angle valves are recommended
Pre-Flush
Always ush out the pipework
before connecting any tapware.
!ATTENTION
Failure to do so will void
the warranty.

3
CLEANING AND MAINTENANCE
Cleaning
Clean with warm soapy water and a smooth
cloth. Avoid abrasive sponges or detergents
as these will damage the nish.
Aerator Maintenance
Unscrew the aerator with 22mm spanner
Immerse for half a day in water-vinegar
solution (80-20%)
Wash, then reassemble

4
Screw the exible hoses into the water inlet
at the bottom of the mixer body, x them by
hand.
2
Screw the threaded rods into the holes at
the bottom of the mixer body and x them
by hand.
1
INSTALLATION INSTRUCTIONS
OLI316 BASIN MIXER | OL003
OLI316 BIDET MIXER | OL018

5
Slide the base and the o-ring over the mixer
assembly then insert the whole block into
the basin hole.
3
BASE
O-RING
While holding the mixer in place, slide in
the rubber gasket and the metal washer
of the xing kit.
Secondly screw the two nuts on the
threaded rods and x them using a wrench.
4
!ATTENTION
Two operators are required to avoid
damages.

6
INSTALLATION INSTRUCTIONS
OLI316 VESSEL BASIN MIXER | OL003H
Screw the exible hoses into the water inlet
at the bottom of the mixer body, x them by
hand.
2
Screw the threaded pipe into the hole at
the bottom of the mixer body and x it by
hand.
1

7
BASE
O-RING
Slide the base and the o-ring over the mixer
assembly then insert the whole block into
the basin hole.
3
While holding the mixer in place, slide in
the rubber gasket and the metal washer of
the xing kit.
Secondly screw the nut on the threaded
pipe and x it using a wrench.
4
!ATTENTION
Two operators are required to avoid
damages.

8
Pull out the protection cap.
1
Slide the plate over the body and to prevent
any rotation, x it to the wall using some glue.
2
LIMITI DEL RIVESTIMENTO
LIMITS FOR WALL LINING
LIMITES DU REVETEMENT
MIN
MAX
please note: the nished wall
lining surface must be within
the minimum/maximum position
marked on the protection cap
Hot
Water
Cold
Water
Mixed
Water
INSTALLATION INSTRUCTIONS
OLI316 SHOWER MIXER | OL031
xing holes
xing hole

9
Insert the handle on the cartridge, then
fasten the screw using the 2.5mm hex key.
3
Insert the chrome cap into the handle hole.
4
CAP

10
Pull out the protection cap.
1
Hot
Water
Cold
Water
Outlet 1 (e.g. Shower)
LIMITI DEL RIVESTIMENTO
LIMITS FOR WALL LINING
LIMITES DU REVETEMENT
MIN
MAX
Slide the plate over the body and to prevent
any rotation, x it to the wall using some glue.
2
Fixing holes
please note: the nished wall
lining surface must be within
the minimum/maximum position
marked on the protection cap
INSTALLATION INSTRUCTIONS
OLI316 DIVERTER MIXER | OL033
Outlet 2 (e.g. Bath)

11
Insert the handle on the cartridge, then
fasten the grub screw using the 2.5 hex key.
Then close the hole on the handle using the
provided cap
3
Starting from the diverter lever assembly,
unscrew the knob and the grub screw.
4
CAP
a
b
c
Insert the handle on the diverter (a) and
fasten the previously removed grub screw
using the hex key (b).
Finally screw the knob into the hole of the
diverter lever (c).
5

12
Once the nished oor lining is done, screw
the metal plate over the top of the recessed
body, x it to the oor using three screws
and plastic plugs.
2
1
Place the internal body into the recessed
area of the floor and fix it using two screws
and plastic plugs.
Then connect the two water supply pipes.
INSTALLATION INSTRUCTIONS
OLI316 BATH FILLER & H/SHOWER | OL077
WATER
SUPPLY
LINE
!ATTENTION
When recessing the body in the floor the
upper threaded part of the body must
protrude just above the finished floor level.
recessed
body
maximum
recessing
line
nished
oor
lining
!ATTENTION
While xing the metal plate to the oor, be
careful not to damage the water line running
under the pavement.
Note that the water inlets are parallel to the
water outles located into the mixer body.
Water
supply
line
Water
outlets

13
BASE
COVER
PLATE
Slide the assembly into the recessed body
(to align the assembly properly, use the
notch into the body).
Fix the whole mixer assembly by rotating the
base cover plate as shown in gure.
3
Connect the hand shower exible hose to
the diverter outlet placed under the spout
4

14
LIMITI DEL RIVESTIMENTO
LIMITS FOR WALL LINING
LIMITES DU REVETEMENT
MIN
MAX
please note: the nished wall
lining surface must be within
the minimum/maximum position
marked on the protection cap
Hot
Water
Cold
Water
Mixed Water
to the spout
xing holes
INSTALLATION INSTRUCTIONS
OLI316 WALL MOUNT MIXER | OL005
xing hole
Pull out the protection cap.
1
Slide the plate over the body and to prevent
any rotation, x it to the wall using some glue.
2

15
Insert the handle on the cartridge, then
fasten the screw using the 2.5mm hex key.
then insert the chrome cap into the handle
hole.
3
Slide the plate over the spout and wrap the
threaded end with PTFE seal tape or hemp.
4
Screw the spout into the mixed water outlet
into the wall.
5

16
Push the spout against the wall, and to
prevent any rotation, x it using some glue.
6