PNC Pit Bull Safety Cover User manual

Pit Bull Safety Cover Installation
Manual
(Channel Version)
Pit Bull © 1994, 2001, 2009, 2017,2021

For help with installation or operation of this product, contact a PNC representative at 832-515-8583
2
Pit Bull Safety Cover
Congratulations on your purchase of the Pit Bull Safety Cover. Your cover is
designed and constructed to “reduce” or minimize injuries sustained in the course of
normal use when installed correctly is not only reliable but convenient to those who
use it. Your Pit Bull is removable and very easy to clean. The polyester fiber does not
absorb water, grease or oil. Pit Bull is knot free and meets or exceeds OSHA and
ANSI safety standards.
If you have any questions or comments, feel free to contact one of our
representatives at 832-515-8385.
WARNING
An improper installed Pit Bull can become unstable and/or malfunction causing
serious injury. READ THESE INSTRUCTIONS CAREFULLY! FAILURE TO FOLLOW
THESE INSTRUCTIONS CAN DAMAGE THE PRODUCT OR CAUSE THE PRODUCT TO
NOT PERFROM CORRECTLY.
Before you begin:
1.Please read this manual in its entirety before you begin the installation process.
2. Follow all instructions thoroughly.
3. EXTREMELY IMPORTANT! Prepare the work area, be sure that all flammable
products have been removed from the service bay and that any paint, grease or
debris has been removed from the area before any welding begins.
4.Use only a certified welding technician that is knowledgeable in safety compliance
and is aware of the area and all safety precautions that need to be engaged.
5. Please follow all General Welding Practices.
Scan QR Code for video installation instructions

For help with installation or operation of this product, contact a PNC representative at 832-515-8583
3
Materials
Materials Provided:
Pit Bull Safety Cover
No –Step Label
Magnetic pins & backings
Detent pins
Sliding channel and rods
Adaptors (10” Bolt/6”Hook)
(4) 1.5” Stainless bolts
(24) Flange Head Nuts
(24) Flange Head Bolts
Other Materials Needed:
All necessary PPE
Pry bar
Drill
Propane torch
Tape measure
Grease or sprayed graphite
Saw
Bolt cutters
Long screwdriver
Crescent wrench

For help with installation or operation of this product, contact a PNC representative at 832-515-8583
4
Step 1: Remove existing pit cover and existing pit cover and existing pit cover tracks
if necessary.
(Optional with Diamond Plate Application)
Step 2: FOR USE WITH LOCKING MECHANISM ONLY! Consider proper location for
locking mechanism.
Measure the inside clearance of the tire guides. The tire guides must be parallel with
+/_ ¼”. Use the narrowest width throughout pit. See example below
If clearance difference is greater than +/_ ¼”, shim between tire guides and sliding
channel to maintain clearance tolerance. Weld shims to tire guides and sliding
channel.

For help with installation or operation of this product, contact a PNC representative at 832-515-8583
5
Step 3:
Welds to be 1” long and 12” on center on both top and bottom, of railing with welds
in an alternate position. CAUTION! Do not WELD the face of the channel.
After welding, Use a Hardened Pry Bar to spread the face of the channel open
slightly. CAUTION! Do not use heavy force to open.
If you need to extend the length of the sliding channels, flare both sections coming
together. Weld the top to secure in place.

For help with installation or operation of this product, contact a PNC representative at 832-515-8583
6
Weld the top to secure in place.
Step 4: Welding is not recommended*
Cut Active/Passive rods (A/P Rods) to correct length. (4”short of the width of the
track to track measurement).
Insert the adaptors onto the ends of the A/P rods.

For help with installation or operation of this product, contact a PNC representative at 832-515-8583
7
Slide the A/P rods into the tracks using the adaptor (10”bolt/6” hook)
Step 5: Adjust the tension of your safety cover using the drill and bolt adjuster on
each T-Bolt.
Drilling them down to the correct depth and cutting off excess length as needed
using bolt cutters.

For help with installation or operation of this product, contact a PNC representative at 832-515-8583
8
Then slide the bolts and cover into the track.
Drill (2) ¼ inch holes through the center channel on all corners at 1 inch and 2 inch
mark from each end.
Insert long bolts into the 1 inch to put a stop to the passive end. Then insert detent
pins into the 2-inch holes on all corners.

For help with installation or operation of this product, contact a PNC representative at 832-515-8583
9
Using a propane torch heat the head of a screwdriver (or soldering iron) until red
hot and poke holes through the crisscross fabric on the bottom 2 rows of your pit
bull safety cover.
Fold the fabric ends over the rod creating a pocket and secure it with the screw and
nut use washer to narrow holes if necessary

For help with installation or operation of this product, contact a PNC representative at 832-515-8583
10
Use a blowtorch to burn off an excess fabric and seal the edges. Then tighten bolts to
secure in place.
Remove detent pen and slide cover between the 1” and 2” drilled holes and re-insert
the detent pin from the bottom and secure. Latch each lanyard to the closest t- Bolt.
Repeat on the other side.

For help with installation or operation of this product, contact a PNC representative at 832-515-8583
11
Spray grease or dry graphite into the track to ensure the bolts run smoothly
Finally place the no step sign 2’-3’ from the foot of both ends using magnetic pins
and backings to secure the cover. WARNING! You cannot remove the label once it has
been secured.
Your Pit Bull Safety Cover Channel system installation is now complete. If you have any
questions about processes or materials, please call a representative today.

For help with installation or operation of this product, contact a PNC representative at 832-515-8583
12
Care and Maintenance
It is not necessary to remove your Pit Bull to clean if you generally wash your pit
area from top to bottom. However, in order to get the maximum life from your Pit
Bull Safety Cover, we recommend you follow the care and maintenance instructions
below.
Professional Netting Concepts LLC. suggests you use a bleach free soap, such as
DAWN Dishwashing Liquid or Woolite Laundry Detergent and hot water. Both these
products are a mild detergent that will not harm your cover. With a medium stiff
brush, apply soap and water over the Pit Bull and scrub. Rinse thoroughly.
Cornstarch or baby talc can be used to remove stubborn grease stains. Brush off
loose dirt, cover the stain with cornstarch or baby talc, and leave on the grease spot
over night. Then brush off the cornstarch or baby talc off. Most, if not all of the stain
should disappear. However, if it is necessary repeat the process again.
For a DEEP CLEAN you can remove your Pit Bull Safety Cover from the channel and
take it to your nearest car wash. Use the foaming brush or high power washer to
clean you Pit Bull Safety Cover. You may use the same process to clean your No-
Step labels.
WARNING!!!
NEVER USE strong cleaners, petroleum based products or bleaches (this includes
Oxi-clean) Avoid using and harsh chemical or industrial strength cleaners. DO NOT
use any cleaning agent that is a solvent based or solvent containing cleanser. These
are typically called degreasers. The use of degreasers over time will fade or lesson
the strength of the webbing material. DO NOT use any kind of hydrocarbon solvent,
it was found to weaken the webbing considerably.
The information contained in this manual is the exclusive property of Professional Netting Concepts, L.L.C. and
protected by copyright and other proprietary rights. Nothing contained in this manual may be reproduced,
distributed or edited in any manner without the prior written authorization of Professional Netting
Concepts, L.L.C. No reproduction is permitted without specific written authorization. You may not
distribute, modify, transmit, reuse, report, or use the contents ofthis information for public or commercial
purposes, including text, images, prices or other information without Professional Netting Concepts, L.L.C.
written permission.

For help with installation or operation of this product, contact a PNC representative at 832-515-8583
13
One- Year Limited Warranty
PARTS –New parts in exchange for the defective parts for one (1) year after original purchase (excluding
shipping and handling charges). This warranty only covers failures due to defects in material or hardware
which occur during normal use. It does not cover failures due to damage in shipment, or failures which are
caused byproducts not supplied by Professional Netting Concepts, L.L.C. or failures which result from an
accident, vehicular traffic, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty
installation (by others not directly employedbyProfessionalNettingConcepts,L.L.C.,andanymodification.
Warrantydoesnotcoverdamagecause by fire, floods, hurricanes, cyclones, tornadoes, earthquakes or any
other extraordinary or unusual event. In no event shall Professional Netting Concepts, L.L.C. be liable for
any consequential damages or for damages to the building or its contents or injury to its occupants.
INSTALLATION –Professional Netting Concepts, L.L.C. will only repair manufacture installations and/or
replace yourcoverfreeofchargeintheU.S.A.intheeventofadefectinworkmanshipormaterial. Installation
warranties are only given on manufacture installations. Manufacture Installations include a one (1) year
warranty from the date of installation. Anyperson, not directly employed by Professional Netting Concepts,
L.L.C. performing installations of Pit Bull Safety Covers will not be covered by the warranty.
This warranty is extended only to the original purchaser. A proof of purchase will be required before
warranty performance is rendered.
The warranty shall be void if Professional Netting Concepts, L.L.C. fails to receive full payment. This
warranty gives you specific legal rights and you may also have rights which vary from state to state.
If a problem with your Pit Bull Safety Cover develops during the warranty period, please contact a
representative with Professional Netting Concepts,L.L.C.

For help with installation or operation of this product, contact a PNC representative at 832-515-8583
14