manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Pneumatic Division
  6. •
  7. Water Filtration System
  8. •
  9. Pneumatic Division IS-F35 Installation and maintenance instructions

Pneumatic Division IS-F35 Installation and maintenance instructions

Filter
w/Manual Drain
Introduction
Follow these instructions when installing, operating, or servicing
the product.
Application Limits
These products are intended for use in general purpose
compressed air systems only.
CAUTION
Polyurethane bowls, sight glass and sight domes on these
units may be attacked by certain chemicals. Never use
solvents like carbon tetrachloride, trichlorethylene, acetone,
or paint thinner to clean any parts. These elements can
cause crazing or failure of the plastic parts. The
polyurethane resin parts are compatible with most
hydrocarbon based synthetic lubricants but, before using,
check with the manufacturer of the lubricant or oil for
compatibility with polyurethane resin.
TO CLEAN POLYURETHANE BOWLS USE MILD SOAP
AND WATER ONLY!
WARNING
To avoid unpredictable system behavior that can cause personal injury
and property damage:
• Disconnect electrical supply (when necessary) before installation,
servicing, or conversion.
• Disconnect air supply and depressurize all air lines connected to
this product before installation, servicing, or conversion.
• Operate within the manufacturer’s specified pressure, temperature,
and other conditions listed in these instructions.
• Medium must be moisture-free if ambient temperature is below
freezing.
• Service according to procedures listed in these instructions.
• Installation, service, and conversion of these products must be
performed by knowledgeable personnel who understand how
pneumatic products are to be applied.
• After installation, servicing, or conversion, air and electrical
supplies (when necessary) should be connected and the product
tested for proper function and leakage. If audible leakage is present,
or the product does not operate properly, do not put into use.
• Warnings and specifications on the product should not be covered
by paint, etc. If masking is not possible, contact your local
representative for replacement labels.
WARNING
FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF
THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR
RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND
PROPERTY DAMAGE.
This document and other information from The Company, its
subsidiaries and authorized distributors provide product and/or system
options for further investigation by users having technical expertise. It
is important that you analyze all aspects of your application, including
consequences of any failure and review the information concerning
the product or systems in the current product catalog. Due to the
variety of operating conditions and applications for these products or
systems, the user, through its own analysis and testing, is solely
responsible for making the final selection of the products and systems
and assuring that all performance, safety and warning requirements
of the application are met.
The products described herein, including without limitation, product
features, specifications, designs, availability and pricing, are subject
to change by The Company and its subsidiaries at any time without
notice.
EXTRA COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FOR
INCLUSION IN EQUIPMENT / MAINTENANCE MANUALS THAT UTILIZE
THESE PRODUCTS. CONTACT YOUR LOCAL REPRESENTATIVE.
Maximum Recommended Pressure Drop:
kPa PSIG bar
Particulate Filter 70 10 0.7
With Polyurethane Bowl
kPa PSIG bar
Operating Pressure Maximum 1034 150 10.0
Operating Temperature Range 4.4°C to 48.9°C
(40°F to 120°F)
With Zinc Bowl
kPa PSIG bar
Operating Pressure Maximum 2068 300 21.0
Operating Temperature Range 4.4°C to 82.0°C
(40°F to 180°F)
With Zinc Bowl & Wrap Around Sight Gauge
kPa PSIG bar
Operating Pressure Maximum 1723 250 17.0
Operating Temperature Range 4.4°C to 65.60°C
(40°F to 150°F)
Piston Drain Installed
kPa PSIG bar
Operating Pressure Maximum 1207 175 12.0
Operating Temperature Range 4.4°C to 65.60°C
(40°F to 150°F)
ANSI Symbols
!
!
!
Pneumatic Division
Richland, Michigan 49083
269-629-5000
Installation & Service Instructions
IS-F35
F35 Particulate Filter
ISSUED: February, 2005
Doc. #ISF35, ECN #050142, Rev. 1
F35 Particulate Filter IS-F35
Installation
1. The filter should be installed with reasonable accessibility
for service whenever possible – repair service kits are
available. Keep pipe or tubing lengths to a minimum with
inside clean and free of dirt and chips. Pipe joint compound
should be used sparingly and applied only to the male
pipe – never into the female port. Do not use PTFE tape
to seal pipe joints – pieces have a tendency to break off
and lodge inside the unit, possibly causing malfunction.
Also, new pipe or hose should be installed between the
filter and equipment being protected.
2. The upstream pipe work must be clear of accumulated
dirt and liquids.
3. Select a filter location as close as possible to the
equipment being protected and upstream of any pressure
regulator.
4. Install filter so that air flows in the direction of arrow on
body.
5. Install filter vertically with bowl drain mechanism at the
bottom. Free moisture will thus drain into the sump “quiet
zone” at the bottom of the bowl.
Bowl Seal
Body
Filter
Element
Bowl (Hand Tighten)
Sight Gauge Retaine
r
Deflector
(Vane Plate)
Element
Retainer
O-Ring
Manual Drain
(Finger Tighten)
Operation and Service
1. To service the filter, it is not necessary to remove the unit
from the airline. Manual drain filters must be drained
regularly before the separated moisture and oil reaches
the bottom of the lower baffle.
2. The particulate Filter Element should be removed and
replaced when pressure differential across the filter is
10 PSIG.
3. Shut off air supply and depressurize the unit, before
servicing.
4. Carefully remove Bowl by turning counterclockwise.
5. Remove Filter Element Retainer and Deflector.
6. Wipe parts, clean with soapy water or denatured alcohol
but do not use denatured alcohol on plastic bowl or
sight gauge. If using compressed air to blow dry, be sure
to wear appropriate eye protection.
7. Install new Filter Element onto Retainer. Install Deflector
onto retainer and reinstall into Filter Body. Install Bowl
hand tight.
8. After servicing, apply system pressure and check for air
leaks. If leakage occurs, Do Not Operate — conduct
servicing again.
Kits Available
Product Bowl
Description Number Type
Bowl*
Polyurethane BKF35A A
Zinc BKF35D D
Zinc with Wrap
Around Sight Gauge BKF35W W
Element Kits
5 Micron EK504VY A, D, W
20 Micron EK504Y A, D, W
Repair Kit
Deflector,
Element Retainer RKF30 A, D, W
Piston Drain (Optional) PKF35 A, D, W
Bowl Seal GSK-504Z101 A, D, W
*Bowl kits include bowl seal.
Lightly grease with provided lubricant.
Inspect for nicks, scratches, and surface imperfections.
If present, reduced service life is probable and future
replacement should be planned.
Clean with lint-free cloth.
Piston Drain
Repair / Conversio
n
Kit

Other Pneumatic Division Water Filtration System manuals

Pneumatic Division F105 Installation and maintenance instructions

Pneumatic Division

Pneumatic Division F105 Installation and maintenance instructions

Pneumatic Division 2FR300D Installation and maintenance instructions

Pneumatic Division

Pneumatic Division 2FR300D Installation and maintenance instructions

Pneumatic Division 2C100F Installation and maintenance instructions

Pneumatic Division

Pneumatic Division 2C100F Installation and maintenance instructions

Pneumatic Division IS-F75 Installation and maintenance instructions

Pneumatic Division

Pneumatic Division IS-F75 Installation and maintenance instructions

Popular Water Filtration System manuals by other brands

GE GX1S50F Owner's manual and installation instructions

GE

GE GX1S50F Owner's manual and installation instructions

Eureka Forbes Under Sink RO user manual

Eureka Forbes

Eureka Forbes Under Sink RO user manual

Bestway 58515 owner's manual

Bestway

Bestway 58515 owner's manual

OMEGA AIR BF 0240 Installation and operating manual

OMEGA AIR

OMEGA AIR BF 0240 Installation and operating manual

LifeSource ScaleSolver SS-5544E Installation, operation and maintenance manual

LifeSource

LifeSource ScaleSolver SS-5544E Installation, operation and maintenance manual

JRC NSVS1115 manual

JRC

JRC NSVS1115 manual

Insignia NS-MWF-1 Quick setup guide

Insignia

Insignia NS-MWF-1 Quick setup guide

Aquasana OptimH2O AQ-RO-3 owner's manual

Aquasana

Aquasana OptimH2O AQ-RO-3 owner's manual

Hydac FluidAqua Mobil FAM 15 Maintenance instructions

Hydac

Hydac FluidAqua Mobil FAM 15 Maintenance instructions

Evolution Aqua Tempest instruction manual

Evolution Aqua

Evolution Aqua Tempest instruction manual

Paragon PW2000F Installation & operation manual

Paragon

Paragon PW2000F Installation & operation manual

Pfeiffer Vacuum OME 16 M/ATEX operating instructions

Pfeiffer Vacuum

Pfeiffer Vacuum OME 16 M/ATEX operating instructions

Follett 01233659 instructions

Follett

Follett 01233659 instructions

Insignia NS-SSHQ531 Quick setup guide

Insignia

Insignia NS-SSHQ531 Quick setup guide

Exhausto VEX350 manual

Exhausto

Exhausto VEX350 manual

Oase Profi Clear Premium Compact L US operating instructions

Oase

Oase Profi Clear Premium Compact L US operating instructions

Hydac OLSW Operating and maintenance instructions

Hydac

Hydac OLSW Operating and maintenance instructions

EHC HT10 Assembly instruction

EHC

EHC HT10 Assembly instruction

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.