Point Mobile PM84 User manual

v1.0, Nov 2023
Copyright © 2023 Point Mobile Co., Ltd. All rights reserved.
Point Mobile Co., Ltd. is the designer and manufacturer of mobile handheld devices.
The Point Mobile logo is a registered trademark and symbol of Point Mobile Co., Ltd.
Features and specifications are subject to change without prior notice.
PM84
Quick Start Guide

2
Device Parts
1. Receiver
2. LED indicator
3. Scan button (Left)
4. Volume buttons
5. Microphone
6. I/O connector for cradle
7. USB connector
8. Speaker
9. Touch screen
10. Front camera
10
1
8
3
7
6
2
4
5
9

3
Device Parts
11. Hand strap holes
12. Rear I/O connector
13. Battery release buttons
14. Scanner
15. Power button
16. Rear camera & Flashlight
17. Scan button (Right)
18. Battery
12
16
15
14
11
13
17
18

4
Product Standard Accessories Battery Replacement
1. Insert the battery from the bottom side (opposite side of the
battery release buttons).
2. Push the battery down until it clicks.
Confirm that the battery release buttons are completely outward,
and the bottom side is fully engaged.
Battery pack
Insert Battery
Remove Battery
LCD protection filmHand strap
USB type C cable
AC Plug
5V 2A power adapter
1. Hold the battery release buttons and press in.
2. While pressing the battery release buttons in, pull the battery up.
open
close
open
close

5
Supported Cards & Card Slot Cover
PM84 provides
•1 microSD card slot
•1 nano SIM card slot –LTE SKU only
Remove the battery, and open the card slot cover to find card slots.
You can use the handle on the bottom side of the cover to open.
Card slot layout
(LTE SKU)
< Notice >
Do not throw away the cover. It affects device sealing performance against
water, dust, etc.
1. Gently slide the card holder left, and swing upwards to open the
holder.
2. Put the proper card with the contacts facing down, close the
holder, and gently slide it right to lock.
Install SD / SIM Card
1 2
4
SD
SIM

6
Turning on /off
Press and hold the power button on the top side of the PM84 until
SMART BEYOND RUGGED logo displays on the screen.
Turn on
When the display is on, press and hold the power button until the
power menu is shown.
Then, tap Power off.
Turn off
Charging the Device
1. Assemble the AC plug, power adapter and USB cable.
2. Connect the cable to the USB connector of PM84.
3. Provide power by plugging the power adapter to the wall socket.
PM84 can also be charged with charging cradle (sold separately).
< Caution >
1. Always use an original power supply from Point Mobile. Other
chargers and cables may damage the PM84.
The device warranty does not cover any damage caused by the usage
of non-original power supplies.
2. Make sure the charger and cable is not wet.
3. Charge in temperatures from 0 ℃ to 45℃.

7
LED Indicator
2
1
No
Indicator
Status
Indication
1
Power
LED
Solid
green
Device
is fully charged
Solid
red
Charging
the device
/
Battery is low
Blinking
red
Charging temperature is out of
normal range
/ Battery is very low
Alternately blinking
red
&green
Cannot
recognize the battery
2
Notification
LED
Blinking
blue
Notification
existing
Red
flash
Barcode
reading failed
Blue
flash
Barcode
reading success
Scan a Barcode
Center the cross-hair aimer or red dot aimer over the barcode. You
can tilt the aimer slightly for a comfortable angle to scan.
Scanner is disabled by default, so enable the scanner from
ScanSettings first.
Check if the scanner icon is placed on the Status bar. Then,
press a scan button on the device to scan a barcode.