Polar Electro 2020 User manual

INSTRUCTIONS FOR
POLAR PANEL MODEL
2022
WWW.POLARVAGNEN.COM

GET STARTED WITH POLAR CONNECT
There are dierent control systems depending on
which year model they apply to.
For the 2013-2018 model year, the system is called
Remote.
2019 - 2022 Polar Connect.
This instruction applies to Polar connect 2020-2022
and is included in each caravan.
Start by downloading the app ¨Polar Connect¨ from
the Appstore or Google Play Store.
Open the app to start the installation.
Click on ”get started with polar connect”.
The app opens the camera.
Go to settings in the Polar Panel - click on Polar con-
nect to get the caravans QR code.
Enter the customer’s email address. Aer this, the
customer receives a verication email to the registered
e-mail address.
Aer you have scanned the QR code, you have 30 mi-
nutes to complete the registration of the subscription.
If it takes longer than 30 minutes, the system locks
down and you must contact Oskar to unlock it.

Check the circle Jag godkänner användar-
villkoren (I approve user conditions) and then click on
fortsätt (continue).
Fill in your E-mail address and click on Skapa konto (crea-
te account)

Login to your E-mail and click on Veriera adress och
välj abonnemang. (Verify address and select subscrip-
tion)
Choose subscription (it’s free for the rst 24 months)
and then press fortsätt. (continue)
Fill in rst name and lastname and then click godkänn
(approve)

Start the aldepanel and hit the MENU- but-
ton.
Scroll down until a box named EXT shows.
Choose the desired temperatur and eect and
the gas o. Press the gear at the bottom right
corner.
Click on EXT.
EXTERN START OF ALDE HEATER RAISE AND LOWER THE TEMPERATURE

Scroll to the right or le until it says EXT and
then hit the return arrow.
Open Polar connect and make sure that heas-
ter is on and then set the desired temperature
down below.
Note! It’s not possible to change the tempera-
ture over the value you put in the aldepanel.
For example, if the Alde display is set on 24
degrees, you cannot go over 24 degrees in the
application.
Turn o the Aldepanel and this text should
show, and aer a few seconds the display will
become dark.

CHANGE LANGUAGE
Start with changing the language on the panel un-
der the settings icon -> select language.
There is no save button. Aer you have selected
your language, click on the house icon in the lower
le corner of the panel to get back to the start-page
again.
SOF T WARE UPDATE
Every caravan has a built-in simcard. When a new soware is available for download, the display detects it
and automatically downloads it along with the les the caravan needs.

CHANGE LIGHT SETTINGS
Click on the indoor lights -> Here are
several dierent ways to set the lighting. You can
change it just as you want it.
Drag the bars under each heading to adjust the
lighting.
SAVE SCENARIO
It´s possible to save up to 4 dierent
scenarios. Click on the letter where you want to
save your scenario in -> adjust the bars - > click
save changes.
To light and extinguish hazard and trunk lighting.
Click on outdoor lights in the start menu.
Click on the icons to turn the lights on and o.

CLIMATE
Click on the heating & comfort icon to start alde-
stove, refrigerator and underoor heating.
Here is also where you start the heating boiler,
cooling-cabinet electronics, electric underoor
heating and underoor heat pump.
WATER LEVELS
Click on the water icon to display the caravans
water level stacks.
CARRIAGE LEVELING
To see how the caravan is tilted, click the
leveleling icon. Here can you see how the caravan
stands horizontally and vertically.
The adjustments are made using the support legs.

VOLTMETER (UPDATE 1.16.0)
Calibrable voltmeter in the panel.
The voltmeter can be seen in the lower corner.
This is calibrable.
To calibrate the voltmeter, you must rst measure
the voltage across the battery terminals.
Then click on Settings -> System.
Here can you calibrate the voltage dierence
between the value you got from the battery and the
value in the panel.