Polygroup 124331173 User manual

TREE ASSEMBLY INSTRUCTIONS
1. Before you start to assemble your tree, choose an appropriate location near a wall outlet.
2. Assemble the tree stand and place on a level surface. (See Fig. A) Then insert the tree pole tightly into the stand.
3. Sort all branches according to color codes marked on the end of each branch. Below is a list of the color codes for your tree. (See Fig. B)
(Please note: the number of rows may vary with different tree sizes.)
Congratulations on purchasing your new tree from Polygroup®!
Carefully follow the instructions below on how to quickly and easily set up your new tree.
Ensure all packaging is removed before assembly and use.
Ensure final assembly is upright and stable.
Fig.B
C
D
B
E
F
G
TREE TOP
ROW
WITHOUT COLOR
COLOR CODED
RED
YELLOW
GREY
D
GREY
DARK BLUE
LIGHT BLUE
DARK PURPLE
H
GREEN
I
ORANGE
G
DARK PURPLE
H
GREEN
I
ORANGE
J
WHITE
K
BURGUNDY
L
PINK
Fig. A - Tree Stand Assembly 1.Unfold the legs and lay the stand in
a flat area.Then slide the locking disc
downward and snap into place.
2. When inserting the bottom section
of the tree into the assembled stand,
thread the eyebolt into the stand and
tighten until the pole is firmly secured.
Eye Bolt
C17 9FT UNLIT GRANGER PINE TREE
MODEL # : TZ90M3W48X00
SKU # : 124331173
Page 1 of 2
Carefully review all instructions. If you have a problem, call or email the
manufacturer. Tree Warranty is Valid through December 31, 2025.
Email: [email protected]
Phone: [phone]
WARNING:
a) Do not use near candles, heaters, or other similar sources of heat.
b) Do not use candles on tree.
c) Artificial trees are made from small fibers that may pose a choking hazard if detached from the branches.Use care around
children and pets.

SHAPING AND ADDING BRANCHES
1. Shape each branch by either placing the branch in a bracket which is at a comfortable level to work (Fig. 1), or holding the branch in your
hand with the hooked end pointing down. (Fig. 2) Begin with the branches at the bottom of the tree and work up towards the top.
2. When shaping each branch, work from the branch hook and move outwards to the end tip of the branch. Start by wrapping the back tip
around the end of the branch stem to cover the branch wire. (Fig. 3)
3. Working from the branch's hook moving outwards, fan each tip out using this pattern: one tip to the right of the branch's center wire, one tip
to the left of the branch's center wire, one tip parallel to the branch's center wire. (Fig. 4) Tips should be slightly offset from each other so that
they do not line up exactly one behind the other. All tips should be curved upwards when looked at from the side. (Fig. 5)
4. As each branch is shaped, place the color coded branch securely into the matching color coded bracket. (Fig. 6) As you finish each level of
branches, make sure the rows look evenly distributed to the levels above and below it. Adjust tips as needed to even appearance. (If your tree
includes branches with side wings, arrange these branches so that the wings are on every other branch if necessary.)
5. When all the branches are shaped and put into their color coded matching brackets, shape the top section. Do this by pulling down each row
of tips in an even, circular pattern. (Fig. 7)
6. Start from the bottom layer of the tree topper and work upwards to the top tip.
7. Carefully curve each tip upwards for a natural look.
8. Insert top securely into tree's center pole. (Fig. 8)
9. Step back and take an overall look at the tree. Shift tips as needed to fill in any gaps. Slightly upsweep all branch tips for a
uniform look. Your Christmas tree is now complete and ready to be decorated. (Fig. 9)
STORAGE TIPS
1. Remove all ornaments and decorations.
2. Start by removing the tree top and then removing each layer of branches going from top to bottom of the tree.
3. In case of difficulty separating the tree pole (trunk), apply a small amount of lubricant at the joint and rotate the upper pole in both
directions. Lift up the upper pole again.
4. Press tips neatly back to the center of branch wire.
5. Carefully place all tree sections and branches into shipping box and tape it shut.
6. When not in use, please store the tree in a cool, dry place away from sunlight.
Fig. 3
Fig. 6 Fig. 8
Fig. 4
Branch
Fig. 5
Side view
Fig. 2Fig. 1
Fig. 9Fig. 7
For any questions, assistance, or missing parts, Do Not Return To Place Of Purchase. Please contact us at [phone]
or visit our website at www.polygroupstore.com. One of our customer service representatives will be happy to assist you.
TREE ID# IS LOCATED ON END PANEL OF BOX.TREE ID# IS REQUIRED WHEN REQUESTING REPLACEMENT PARTS.
CUSTOMER SERVICE FOR CHRISTMAS TREES
Tree ID#:
Tree UPC#:
Store Purchased:
Specify Problem:
Customer Name:
Address:(No P.O. Boxes)
City & State:
Zip Code:
Day Phone:
Date Purchased:
Page 2 of 2