Polygroup TG80P2762D00 User manual

TREE ASSEMBLY INSTRUCTIONS
SNOITCURTSNIYLBMESSA MADE IN CHINA
MODEL #: TG80P2762D00
Congratulations on purchasing your new tree from Polygroup®! Carefully follow the instructions below on how to
quickly and easily set up your new tree.
Fig. 1
Tree Stand Assembly
Click
Pull apart the legs of the stand so that they are
snapped into an x-shape, place the tree stand on a
level surface.
To close the stand, press the metal button and fold
the legs together.
Assemble
Yellow Labels
Together
Assemble
Red Labels
Together
Assemble
Purple Labels
Together
Assemble
Blue Labels
Together
Assemble
Pink Labels
Together
Assemble
Orange Labels
Together
*Electrical Rating For The Tree
(For Indoor And Outdoor Use)
0.7A 120V 60Hz
STEP 2
Insert middle section 2/5 into bottom section 1/6.
STEP 3
Snap together top sections 3 and sections 4 to
form arch top.
STEP 4
Insert pre-shaped arch top (sections 3 and
sections 4) into middle section 2/5.
STEP 5
Connect the light strings as shown in Fig. 1.
NOTE:
1. For outdoor ground use. Push the stakes into
ground as shown (Fig 1).
2. If you want to use timer, please plug the
power plug into the timer (Fig 1).
STEP 1
Insert bottom section 1/6 into tree stand.
Pre-installed
V-Shape Spring
Pin (w/1 extra)
Timer
1pc
Metal stand
2 pcs
Section 4
1 pc
Section 3
1 pc
Section 2/5
2 pcs
Section 1/6
2 pcs
Parts
Ground Stake
4 pcs
Section 4 Section 3
Section 5
Section 6
Section 2
Section 1
STEP 4
STEP 2
STEP 4
STEP 2
STEP 1 STEP 1
STEP 3
Insert
Green Label
Plug Into Wall
Outlet

SNOITCURTSNIYLBMESSA MADE IN CHINA
STORAGE INSTRUCTIONS:
1. Remove the light strings from the power supply and disconnect the two end-to-end connectors in each side
of the archway tree.
2. Disassemble the tree from the top to the bottom. Start with the tree top and gently lift straight up to remove
from section below and fold all tips toward the pole.
3. In case of difficulty separating the tree pole (trunk), apply a small amount of lubricant at the joint and
rotate the upper pole in both directions. Lift up the upper pole again.
4. Continue by gently lifting straight up each section(s) from the section below and fold all tips toward the pole
until the bottom section is removed from the tree stand.
5. Carefully place all tree sections into shipping box and tape it shut.
6. When not in use, please store your tree in a cool, dry place away from sunlight. Exposing your tree to
excessive heat or humidity may damage your tree.
CUSTOMER SERVICE FOR CHRISTMAS TREES
For any questions, assistance, or missing parts, Do Not Return To Place Of Purchase. Please contact
us at 1-888-919-0070 or visit our website at www.polygroup.com. One of our customer service
representatives will be happy to assist you.
TREE ID# IS LOCATED ON END PANEL OF BOX.TREE ID# IS REQUIRED WHEN REQUESTING REPLACEMENT PARTS.
Customer Name:
Address:(No P.O. Boxes)
City & State:
Zip Code:
Day Phone:
Date Purchased:
Tree ID#:
Tree UPC#:
Store Purchased:
Specify Problem:
TROUBLE SHOOTING TIPS
For Pre-lit Trees, If The Tree Does Not Illuminate
1. Please check to make sure that all plugs are properly connected and power cord is plugged into the wall outlet.
Refer to assembly guide for instructions. (If the tree comes with a foot pedal, try stepping on the on/off button).
2. Please check for blown fuses at the light string plugs and power cord plug. Replace as needed.
Note: Please make sure to use appropriate replacement fuses as indicated on the light string plug and power cord
plug.
3. Please check for loose, broken or missing light bulbs and replace as needed.
OPERATING INSTRUCTIONS
HOW TO USE THE LIGHT CONTROLLER:
Press the selector button on the “Light Controller”
(1) CLEAR AND MULTICOLOR ALTERNATING; (2) CLEAR LIGHTS;
(3 MULTI LIGHTS and (4) TURN OFF BOTH LIGHTS.
Light
Controller
Selector
Button