Porter Athletic Powr-Touch 5.0 Operating instructions



INST12800200
©2017PORTERATHLETIC,INC.ALLRIGHTSRESERVED. 11/6/2017
IsthePowr‐Touch
5.0assignedthe
correctIPaddress?
Proceedtothelastpageof
thefollowinginstrucons.
YES
Idon’t
know
NO
Proceedtopage3to
re‐assignthePowr‐
Touch5.0IPaddress.
P G
N. 12800 P‐T® 5.0 C S
YES
Doesyouroperangdevice
(tablet,PC)runonthesame
networkastheaddressassigned
toyourPowr‐Touch5.0andis
theassignedaddressavailableon
yournetwork?
Proceedtopage2to
determineyourdevice
network.AskITfor
availableaddresses.
Idon’t
knowNO
START
TheaddressassignedtoyourPowr‐
Touch5.0canbefoundinyour
submialdocuments,whichare
shippedinapocketinsidethePowr‐
Touch5.0panel.Lookforapagein
the“ElectricalDrawings”secontled
“PLCSETTINGS”.Under“EBOX—
COMMUNICATIONSSETUP”itwilllist
theassignedIPaddress.Thedefault
addressis10.0.0.2.


2
FindacomputerconnectedtothenetworkthatwilloperateyourPowr‐Touch5.0.Forexample,alaptopconnectedtothesame
wifisignalasthetabletthatwilloperatethePowr‐Touch5.0Gotoyourcomputer’snetworkconneconinformaon.
ForWindows7,clickthelowerle“Start”buon,then“ControlPanel”,then“NetworkandSharingCenter”
Clickontheblue“LocalAreaConnecon”forthenetworkthathas“Internet”access.Clickonthe“Details…”buontodetermine
yourIPv4Address.Makeanoteofthenumbersinthegreenboxesintheimageonthelowerrightofthispage.Whenyou’ve
recordedthenumbers,closethe“Details”windowbyclickingthe“Close”buon.
Checking your Operating Device IPAddress
3.Clickhere
1.Clickhere2.Clickhere
4.Clickhere
ThisisyourPC’s
IPAddress
Thiscomputer
isonthe
172.16.0.0
network.
Othercommon
networksare:
10.0.0.0and
192.168.0.0


3
Ifyouhaven’talreadycheckedyourIPaddressaccordingtothe
previousinstruconsbeginningonpage2,pleasedosonow.
Leavethe“LocalAreaConneconStatus”windowopen.Clickon
“Properes”.
 Re‐assign your computer’s IP address to be on the same
network as the default ebox IP address. The default network
is 10.0.0.0.
Fromthe“LocalAreaConneconProperes”window,highlight
“InternetProtocolVersion4(TCP/IPv4)”andclickthe“Properes”
buon.Selectthe“UsethefollowingIPaddress”radiobuonand
enterthefollowing:

IPaddress:10. 0.0.50
Subnetmask: 255.255.255.0
Defaultgateway:10.0.0.1

Asshownintheimagetothelowerright.

Youcanleavethe“DNSserver”addressesblank.
Re-assigning your PC IPAddress
5.Clickhere
6.Clickhere
Clickthe“OK”buon.Proceedtothefollowingpagetore‐assigntheeboxIPaddress.
8.Clickhere
7.Typethe
numbersas
shown.


4
 Reassign the IP address on your Powr‐Touch 5.0 ebox
UsinganEthernetcord,connecttheeboxtothesamecomputer
thatyoujustassignedanaddressonthe10.0.0.0network.
Plugintheeboxacadapter.Powerontheeboxwiththeswitch.
Re-assigning the ebox IPAddress
ComputerwithEthernetport,
internetaccess,theGoogle
Chromebrowser,andstacIP
onthe10.0.0.0network.
Powr‐Touch5.0ebox
Defaults:
IPaddress:10.0.0.2
Netmask:255.255.255.0
Gateway:10.0.0.1
Eboxpower
switch
Onceconnected,accesstheeboxunit’sadminpagebytyping
“10.0.0.2/admin”intotheaddressbarintheGoogleChrome
browser.ChromeisrequiredtousethePowr‐Touch5.0soware.
ACAdapterto
120Vpower
Ethernetto
Internet
(oponal)
Ethernetto
computer
9.Typehere:
10.0.0.2/admin
PressEntertobe
takentothe“Staon
ApacheServer”page
Default
addressesare
shown


5
UpdatetheIPinformaontoworkwithyourlocalnetwork.AskyourITdepartmentforanavailableaddressifnecessary.Ifyou
arenotgivenaspecificaddress,trychangingjustthelastgroupofnumbersintheIPtoanumberbetween4and256.
Examples:
Ex1:TheoriginalcomputerIPaddresswas192.168.1.31
Thenyoumightenterintheeboxadminpage:
IPAddress: 192.168.1.32
Netmask:255.255.255.0 (thisshouldmatchthecomputer’soriginalsubnetmask)
Network: 192.168.1.0
Gateway:192.168.1.1(thisshouldmatchthecomputer’soriginaldefaultgateway)
Broadcast: 192.168.1.255
ControllerIP:192.168.1.33(iftherearemulplePLCs,usetheaddressofthefirstPLC)
Ex2:TheoriginalcomputerIPaddresswas172.16.9.15
Inthiscaseyoumightenterintotheeboxadminpage:
IPAddress:172.16.2.50
Netmask: 255.255.240.0 (thisshouldmatchthecomputer’soriginalsubnetmask)
Network:172.16.0.0(Foreachnumbergroup,ifthenetmaskis255,thisshouldbethesameastheIP,and
ifthenetmasknumberislessthan255,itshouldbe0,unlesstoldotherwisebyIT)
Gateway: 172.16.0.1 (thisshouldmatchthecomputer’soriginalgateway)
Broadcast:172.16.15.255 (Foreachnumbergroup,ifthenetmaskis255,thebroadcastnumbershouldmatch
theIPaddress.Ifthenetmaskislessthan255,thebroadcastshouldbethenetmask
subtractedfrom255)
ControllerIP:172.16.2.52(iftherearemulplePLCs,usetheaddressofthefirstPLC)
It is imperave that the network be set correctly! If the network is set incorrectly, the ebox will not connect, and a mouse,
keyboard, monitor, and phone call to support will be required.
Recordtheenteredaddressesonpage7ofthisguide.Clickthe“Submit”buon.

Changeyourcomputer’sIPaddressbacktoitsoriginalassignmentfollowingthesequenceofinstruconsonpage3again.
Re-assigning the ebox IPAddress
10.Enterthe
addressestobe
usedhere.
Addressesfor
Example2are
shown.
11.Clickhere.


6
 Update the IP address for the PLC (Programmable Logic Controller) unit in the Powr‐Touch 5.0 panel.
1.Powerthecontrolpanel.Pressthe[ESC]keytoenterthe
mainmenu.
2.Scrolldownunlthecursorispointedto“Advancedset.”
Press[OK]
3.Scrolldownunlthecursorispointedto“ENETCfg”.
Press[OK]
4.Scrolldownunlthecursorispointedto“IPAddress”.
Press[OK]
5.“ENETSetup:MasterPassword”willappear.Leavethe
passwordblankandpress[OK].
6.“ENETMode:sta”appears.Press[OK].
7.“IPaddress”appears.UsethearrowstochangetheIPto
matchthe“ControllerIP”intheeboxset‐up.Press[OK].
Re-assigning the PLC IPAddress
REMOTE
▶I/O Status
Monitoring
Mode Switch
REMOTE
User Display
▶Advanced Set
REMOTE
KeyIn Mode
DCOMM Cfg
▶ENET Cfg
REMOTE
ENET Cfg:
Status
▶IP Address
REMOTE
ENET Setup:
Master Password:
____________
REMOTE
ENET Mode: stati
Press [U/O] key
REMOTE
ENET Mode: static
IP address
172.016.002.052
ThedefaultPLCaddressesare:
IPaddress: 010.000.000.003
SubnetMask: 255.255.255.000
DefaultGateway: 010.000.000.001
MicroLogix1400PLCin
Powr‐Touch5.0panel
Ifyouhavemorethanonepanelandebox,theeboxfromthe
secondpanelwillhavethesedefaultaddresses:
IPaddress: 10.0.0.12
SubnetMask: 255.255.255.0
DefaultGateway: 0.0.0.0
AndthesecondPLCwillhavethesedefaultaddresses:
IPaddress: 010.000.000.013
SubnetMask: 255.255.255.000
DefaultGateway: 010.000.000.001
AddionalpanelswillconnuetoincrementtheIPaddressbyten.


7
8.“SubnetMask”appears.Usethearrowstochange.
Press[OK].
13.Press[ESC]unlthedisplaychangestoshow“I/O
Status”.
Re-assigning the PLC IPAddress
REMOTE
ENET Cfg:
Status
▶IP Address
REMOTE
ENET Mode: static
Subnet Mask
255.255.255.000
REMOTE
ENET Mode: static
Gateway address
172.016.000.001
REMOTE
ENET Mode: static
Pri DNS
000.000.000.000
REMOTE
ENET Mode: static
Sec DNS
000.000.000.000
REMOTE
▶I/O Status
Monitoring
Mode Switch
11.“SecDNS”appears.Thisisnotused.Leaveasallzeros.
Press[OK].
12.“ENETCfg:”willappear.
9.“Gatewayaddress”appears.Usethearrowstochange.
Press[OK].
10.“PriDNS”appears.Thisisnotused.Leaveasallzeros.
Press[OK].
Pleaserecordyoursystemaddresseshereforyourfuturereference.
Ebox:
IPAddress: ___.___.___.___
Netmask:___.___.___.___
Network: ___.___.___.___
Gateway:___.___.___.___
Broadcast: ___.___.___.___
ControllerIP:___.___.___.___
VPNConnectionIP:___.___.___.___

PLC:
IPAddress: ___.___.___.___
SubnetMask:___.___.___.___
Gatewayaddress:___.___.___.___



Ifyouhavemorethanonepanel,youcanrecordtheaddionalIP
addresseshereforyourreference.
Ebox 2:
IPAddress: ___.___.___.___
PLC 2:
IPAddress: ___.___.___.___
Ebox 3:
IPAddress: ___.___.___.___
PLC 3:
IPAddress: ___.___.___.___
Ebox 4:
IPAddress: ___.___.___.___
PLC 4:
IPAddress: ___.___.___.___
14.Press[OK].


8
Ifyouneedaddionalassistance,youmayinstallthefreedownloadTeamViewer12forremotehelp.
hps://www.teamviewer.us/?utm_source=bing&utm_medium=cpc&utm_campaign=us_s_brand&pid=bing.us.desk.brand.tv_12_ex

PleasecontactPorteratPowertouch5@porterathlec.comwithanyquesons.
601 Mercury Drive, Champaign, IL U.S.A. 61822
www.porterathletic.com
[phone]
SAVE THESE INSTRUCTIONS FOR FUTURE USE
EntertheIPaddressassignedtotheebox(forexample:172.16.2.50)intotheaddressbarofGoogleChromeonaninternet‐
capabledeviceconnectedtothesamenetworkasthePowr‐Touch5.0eboxandPLC.

 Connect the ebox to the Powr‐Touch 5.0 panel.
Iftheeboxisnotalreadyconnectedtothepanel,connecttheEthernetcableinthepaneltoport“2”oftheeboxandconnectthe
ACadaptertoapowersource.Theeboxdoesnotrequiremounngandmaybesetanywhereinsidethepanelbox.Poweronthe
eboxusingthepowerswitch.Therewillbesolidandblinkinglightswhenitison.
Installing the ebox
Eboxpower
switch
If the PLC IP address has changed from the default, you will need to update it in the app. Aer entering the default passcode
(1234), select [ENTER] then [AGREE]. Select the [SETTINGS] buon, then “Change IP Address”. Enter the address of the PLC
associated with the ebox. Select [SAVE].
ProceedtothePowr‐Touch5.0Owner’sManualforaddionaldetailsonmodifyingsengsandadjusngequipment.
Ifyournetworkchanges(e.g.:yougetanewinternetserviceprovider),youmayneedtofollowthisguideagaintochangeyour
eboxandPLCaddressesinthefuture.