Porter-Cable DA250B User manual

FINISH NAILER
MODEL DA250B
IMPORTANT
Please make certain that the person who is
to use this equipment carefully reads and
understands these instructions before
starting operations.
The Model and Serial No. plate is located on the main
housing of the tool. Record these numbers in the
spaces below and retain for future reference.
Model No.
Type
Serial No.
Part No. 903898 - 04-01-04

PORTER*CABLE
Porter-Cable Corporation
4825 Highway 45 North
Jackson, TN 38305
GB ENGLISH
EC-DECLARATION OF
CONFORMITY
We declare under our sole responsibility that
this product is in conformity with the
regulations EN292-2: section 3 of 1992
EN292-1: section 5 of 1992
EN1050:1993
EN792 13:2000
EESPANOL
DECLARACION DE
CONFORMIDAD "CE"
Declaramosbajonuestrasolaresponsabilidadqueest e
producto estaen conformidadcon lasregulaciones
EN292-2: section 3 of 1992
EN292-1: section 5 of 1992
EN1050:1993
EN792 13:2000
F.FRANQAISE
DECLARATION DE CONFORMITI_ CE
Nous declarons sous notre propre responsabilite que
ce produit est conforme aux reglementations
EN292-2: section 3 of 1992
EN292-1: section 5 of 1992
EN1050:1993
EN792 13:2000
Rebert F. Burkholder
St. Vice Presidem otTechnology
PROFESSIONAL POWER TOOLS
Date of Manufacture:
Fecha de fabricaci6n:, Date de fabrication:
Serial No:
NOmero de serie:, Nombre d'ordre
2

This manual contains information that is important for you to know and under-
stand. This information relates to protecting YOUR SAFETY and PREVENTING
EQUIPMENT PROBLEMS. To help you recognize this information, we use the
symbols below. Please read the manual and pay attention to these sections.
indicates an imminently hazardous situation which, if not avoided,
will result in death or serious injury.
indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
indicates a potentially hazardous situation which, if not avoided,
may result in minor or moderate injury.
used without the safety alert symbol indicates potentially
hazardous situation which, if not avoided, may result in property
damage.
SAVE THESE INSTRUCTIONS!
Improper operation or maintenance of this product could
result in serious injury and property damage. Read and understand all
warnings and operating instructions before using this tool. When using
pneumatic tools, basic safety precautions should always be followed to
reduce the risk of personal injury. For additional information visit our
website www.porter-cable.com.
Additional Information regarding the safe and proper operation of air
nailer and fastener tools (i.e. a safety video) is available from the
International Staple, Nail and Tool Association (ISANTA)
(www.isanta.org). Additional Information regarding the safe and proper
operation of power tools (i.e. a safety video) is available from the Power
Tool Institute, 1300 Sumner Avenue, Cleveland, OH 44115-2851
(www.powertoolinstitute.com). Additional Information is also available
from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL
60143-3201, the American National Standards Institute ANSI 01.1Safety
Requirements for Woodworking Machines, and the U.S. Department of
Labor regulations.
READ AND FOLLOW ALL INSTRUCTIONS.
_There are certain applications for which this tool was
designed. Porter-Cable strongly recommends that this tool NOT be modified
and/or used for any application other than for which it was designed. If you
have any questions relative to its application DO NOT use the tool until you
have written Porter-Cable and we have advised you.
Technical Service Manager
Porter-Cable Corporation
4825 Highway 45 North
Jackson, TN 38305

1. Read and understand tool labels and
manual. Failure to follow warnings could
result in DEATH or SERIOUS INJURY. Fig. 1.
Fig. 1
2. Operator and others in work area MUST
wear safety glasses with side shields.
These safety glasses must conform to ANSI
Z87.1 requirements (approved glasses have
"Z87" printed or stamped on them). Fig. 2.
3. Keep fingers AWAY from trigger when
not driving fasteners to avoid accidental
firing. Never carry tool with finger on
trigger. In "contact actuation mode", tool
will fire a fastener iftool is bumped.
4. Choice of triggering method is
important. Check manual for triggering
options. See "Using the Tool with Different
Triggering Options" section of this manual.
5. Never point tool at yourself or others
in work area. Serious injury or death may
occur if the tool is activated. Fig. 3
6. Never use oxygen or other bottled
gasses. Explosion will occur. Never use
combustible gases or any other reactive
gas as a power source for this tool:
explosion and serious personal injury will
result. Fig. 4.
7. Wear ear protection to safe-guard
against possible hearing loss. Ear
protection equipment must conform to ANSI
$3.19 requirements. Fig. 5.
Fig. 2
Fig. 3
Fig. 4
Fig. 5
8. Use clean, dry, regulated, com-
pressed air at 70 to 120 PSI, (4.8 to 8.3
BAR). Fig. 6. Fig. 6

9. Do not connect tool to pressure which
potentially exceeds 200 PSI (13.7 BAR).
10. All air line components (hoses,
connectors, filters, regulators, etc.) must
be rated for a maximum working pressure
of at least 150 PSI (10.3 BAR) or 150% of
the maximum system pressure, which ever
is greater.
11. Connect tool to air supply hose with a
coupling that automatically removes all
pressure from the tool when the coupling is
disconnected. Fig. 7.
12. Disconnect tool from air supply hose
before doing tool maintenance, clearing a
jammed fastener, leaving work area, moving
tool to another location, or handing the tool
to another person. Fig. 7.
13. Never use a tool that is leaking air, has
missing or damaged parts, or requires
repair. Make sure all screws and caps are
securely tightened. Fig. 8.
14. Never use tool if safety, trigger or
springs are inoperable, missing or
damaged. Do not alter or remove safety,
trigger, or springs. Make daily inspections
for free movement of trigger and safety
mechanism. Fig. 8.
15. Do not use tool without safety
warning label. If label is missing, damaged
or unreadable, contact your Porter-Cable
Service Center for a replacement. Fig. 9.
16. Only use parts, fasteners and
accessories approved by Porter-Cable.
17. Connect tool to air supply before
loading fasteners, to prevent a fastener
from being fired during connection. The tool
driving mechanism may cycle when tool is
connected to the air supply. Fig. 10.
18. Always assume the tool contains
fasteners. No horseplay. Respect the tool
as a working implement. Fig. 11.
19. Operator and bystanders should wear
hard hats to safeguard against possible
injuries. Fig. 12.
20. Do not load fasteners with trigger or
safety depressed, to prevent unintentional
firing of a fastener. Fig. 13
Fig. 12
Fig. 7
Fig. 8
Fig. 9 DANGER
Fig. 11
Fig. 10
Fig. 13

21. Remove finger from trigger when not
driving fasteners. Never carry tool with finger
on trigger. In "Contact Actuation Mode" tool
will fire a fastener if safety is bumped while
trigger is depressed. Fig. 14.
22. Do not overreach. Keep proper footing
and balance at all times when using or
handling the tool.
23. Fire fasteners into work surface only:
never into materials too hard to penetrate.
Fig. 15.
24. Grip tool firmly to maintain control
while allowing tool to recoil away from
work surface as fastener is driven. In
"Contact Actuation Mode" if safety element
is allowed to recontact work surface before
trigger is released an unwanted fastener will
be fired.
25. Do not drive fasteners on top of other
fasteners, or with the tool at too steep an
angle: the fasteners can ricochet causing
personal injury. Fig. 15.
26. Do not drive fasteners close to the
edge of the workpiece. The workpiece is
likely to split allowing the fastener to fly free
or ricochet causing personal injury. Fig. 16.
Fig. 14
A
?,
Fig. 15
Fig. 16
27. FOR TOOLS USED IN CONTACT
ACTUATION MODE, Do not use on
scaffoldings or ladders or for tasks in
which changing location involves the use of
scaffoldings, stairs, ladders, and the like. Do
not use for specific tasks such as closing
boxes or crates or fitting transportation
safety systems on vehicles and wagons.
Fig. 17.
Fi_
TECHNICAL SPECIFICATIONS
Noise level Typical Mean
A - Weighted sound impulse ... effective Acceleration .... 5.4 m/s 2
power level ...... 101 dBA
P - Emission sound pressure
pressure level ...... 93 dBA

Employer must enforce compliance with the safety warnings and all other
instructions contained in this manual.
Keep this manual available for use by all people assigned to use this tool.
For personal safety and proper operation of this tool, read and understand
tool labels and manual. Failure to follow warnings could result in DEATH or
SERIOUS INJURY. Read and follow all of these instructions carefully.
Porter-Cable Model DA250B is a heavy duty pneumatic finish nailer. It is
designed to install 15 ga. finish nails of various lengths from 11/4" to 21/2''
long. Use approved Porter-Cable fasteners only.
POWER SOURCE
This tool is designed to operate on clean, dry, compressed air at regulated
pressures between 70 and 120 PSI (Pounds per Square Inch)(4.8 to 8.3 BAR).
The preferred system would include a filter, a pressure regulator, and an
automatic oiler located as close to the tool as possible, within 15 ft/4.6 m is
ideal.
All compressed air contains moisture and other contaminates that are
detrimental to internal components of the tool. An air line filter will remove
most of these contaminates and significantly prolong the life of the tool. If an
in-line oiler is not available: place five or six drops of Porter-Cable Air Tool Oil
into the tool's air inlet at the beginning of each workday.
The tool is equipped with a 1/4" male "quick connector". A 3/8" male "quick
connector" is available from Porter-Cable and may be used in situations where
a 1/4"supply line is not available. The tool must always be connected to the air
supply with a coupling such that all pressure is removed from the tool when the
coupling is disconnected.
PREPARING THE TOOL
1. After reading and understanding this entire manual, connect tool to
air supply (Fig. 18).
2. Orient a strip of approved fasteners with points down (A) Fig. 19, align,and
insert into the magazine "T" slot points first.
Do not load fastener strip into magazine backwards.
I
Fig. 18
7
Fig. 19

3. Observe fastener icon (A) Fig. 19A. Insert fasteners (B) Fig. 19A with
points down (C) Fig. 19A. Slide fasteners forward to the front of the
magazine. The magazine will hold two full strips of fasteners.
IMPORTANT" Fasteners must point in the same direction as they will be
driven.
4. Feed the strip of fasteners into the magazine ("T" slot), until they are past
the spring (A) Fig. 20.
5. Pull the follower (B) Fig. 21, all the way to the rear of the magazine and
release. The follower will apply pressure to the strip of nails to feed it into the
driving mechanism.
6. Adjust directional exhaust deflector (A) Fig. 22, so that the exhaust air
blast will be directed away from the operator. The exhaust deflector provides
seven detented positions for directing the exhaust blast away from the
operator. Grasp the deflector and rotate it to the desired position for the
current application.
Fig. 19A
Fig. 21
Fig.23
8

[o] _ _ :_;t/l_[_ I]_[._o..]ijd[o]_[.."]
USING THE TOOL WITH DIFFERENT TRIGGERING OPTIONS
Complete all steps of PREPARING THE TOOL before using the tool.
This tool is shipped from the factory with a "single sequential actuation"
trigger which will limit the tool to firing method number 1 only.
A "contact actuation" trigger is available. The "contact actuation" trigger
allows the tool to be fired in either of two methods described below;
1. [SINGLE SEQUENTIAL ACTUATION TRIGGER]: To fire, grip tool firmly
to maintain control, position nose of tool onto work surface, push the tool
firmly against work surface to depress safety (S) Fig. 23, and squeeze
trigger to fire a fastener. Allow tool to recoil away from work surface as
fastener is driven. This "single sequential actuation" method provides the
most accurate fastener placement. -OR-
2. [CONTACT ACTUATION TRIGGER]: To fire, grip tool firmly to maintain
control, squeeze and hold trigger, push the tool firmly against work surface.
Allow tool to recoil away from work surface as fastener is driven. If safety
element is allowed to recontact work surface before trigger is released an
unwanted fastener will be fired. The tool will fire a fastener each time the
safety is depressed. This method is known as "contact actuation" and
allows very fast repetitive fastener placement.
IMPORTANT: A "contact actuation" trigger is available free-of-charge by
calling 1-800-321-9443 in the United States and Canada or 001-731-660-
9374 outside the United States and Canada, and providing tool model and
serial number. For identification purposes: the contact actuation trigger is
black and the single sequential actuation trigger is red.
_Disconnect tool from air supply before performing
maintenance, clearing a jammed fastener, leaving work
area, moving tool to another location, or handing the tool
to another person.
_Clean and inspect tool daily. Carefully check for proper
operation of trigger and safety mechanism. Do Not use the tool unless
both the trigger and the safety mechanism are functional, or if the tool is
leaking air or needs any other repair.
The depth to which a fastener is driven is controlled by the depth adjustment
knob (A) Fig. 24. The depth of drive is factory adjusted to a nominal setting.
Test fire a fastener and check depth. If a change is desired, rotate the
adjustment knob (A) Fig. 24. The adjustment knob has detents every 1/4turn.
Rotate the knob (A) Fig. 24 clockwise to increase the depth of drive, rotate
the knob counterclockwise to decrease the
depth of drive. Test fire another fastener and
check depth. Repeat as necessary to
achieve desired results. The amount of air
pressure required will vary depending on the
size of the fastener and the material being
fastened. Experiment with the air pressure
setting to determine the lowest setting that
will consistently perform the job at hand. Air
pressure in excess of that required can
cause premature wear and/or damage to the
tool.

Fig. 25 Fig. 26
A rubber nose cushion (A) Fig. 25, is provided to reduce marring of the work
surface. The rubber cushion can be removed to provide increased depth-of-
drive for toe-nailing applications. When not in use, a storage location is
provided for the the rubber cushion on the magazine (A) Fig. 26.
Disconnect tool from air supply before removing or
re-installing rubber cushion.
CLEARING A JAMMED FASTENER
_Disconnect tool from air supply.
1. Remove any remaining fasteners from the nailer.
A. Place finger in recess (A) Fig. 27, and push lever to release follower
mechanism.
B. Slide the follower to the end of the magazine (refer back to Fig. 21).
C. Depress the lever (A) Fig. 28, to release follower mechanism, and slide
all remaining fasteners out of the magazine.
NOTE: Make sure tip (B) Fig. 28 clears nail strip.
:ig. 28
2. Open the quick release latch and hinge the fastener guide plate open (B)
Fig. 29.
3. Remove the jammed fastener (see Fig. 30).
4. Close the fastener guide plate and secure with the quick release latch.
10

Fig, 29 Fig. 30
CLEAN AND INSPECT DAILY
_Disconnect tool from air supply before cleaning and
inspection. Correct all problems before placing the tool back in use.
Wipe tool clean and inspect for wear or damage. Use non-flammable
cleaning solutions to wipe exterior of tool only if necessary. DO NOT SOAK
tool with cleaning solutions. Such solutions can damage internal parts.
Inspect trigger and safety mechanism to assure system is complete and
functional: no loose or missing parts, no binding or sticking parts.
Keep all screws tight. Loose screws can cause personal injury or damage
tool.
If tool is used without an in-line oiler: place 5 or 6 drops of Porter-Cable Air
Tool Oil into the air inlet of the tool at the beginning of each workday.
SERVICE AND REPAIRS
All quality tools will eventually require servicing or replacement of parts due
to wear from normal use. These operations should ONLY be performed by
either an AUTHORIZED PORTER-CABLE SERVICE STATION or a PORTER-
CABLE.DELTA FACTORY SERVICE CENTER. All repairs made by these
agencies are fully guaranteed against defective material and workmanship.
We cannot guarantee repairs made or attempted by anyone other than these
agencies.
Should you have any questions about your tool, feel free to write us at any
time. In any communications, please give all information shown on the
nameplate of your tool (model number, type, serial number, etc.).
11

Disconnect tool from air supply before performing any Service
Procedure.
SYMPTOM PROBLEMS SOLUTIONS
1. Air leak near top of Loose screws. Tighten screws.
tool or intrigger area. Worn or damaged Install Overhaul Kit.
o-rings or seals.
2. Tool does nothing or Inadequate air supply. Verify adequate air supply.
operates sluggishly. Inadequate lubrication. Put 5 or 6 drops of oil into air inlet.
Worn or damaged Install Overhaul Kit.
o-rings or seals.
3. Air leak near bottom Loose screws. Tighten screws.
of tool. Worn or damaged Install Overhaul Kit.
o-rings or bumper.
4. Tool jams frequently. Incorrect fasteners. Verify approved fasteners of
correct size.
Replace w/undamaged fasteners.
Tighten screws.
5. Other.
Damaged fasteners.
Magazine or nose
screws loose.
Magazine is dirty.
Driver is worn or damaged. Clean magazine.
Install "DRIVER" Maintenance Kit.
Contact a Porter-Cable
Service Facility.
A complete line of accessories is available from your Porter-Cable • Delta
Supplier, Porter-Cable • Delta Factory Service Centers, and Porter-Cable
Authorized Service Stations. Please visit our Web Site www.porter-cable.com
for a catalog or for the name of your nearest supplier.
_Since accessories, other than those offered by Porter-
Cable • Delta, have not been tested with this product, use of such
accessories could be hazardous. For safest operation, only Porter-Cable
• Delta recommended accessories should be used with this product.
PORTER-CABLE LIMITED
ONE YEAR WARRANTY
Porter-Cable warrants its nailing and stapling tools for a period of one year from the date of original
purchase. We will repair or replace at our option, any part or parts of the product and accessories
covered under this warranty which, after examination, proves to be defective in workmanship or
material during the warranty period. For repair or replacement return the complete tool or accessory,
transportation prepaid, to your nearest Porter-Cable Service Center or Authorized Service Station.
Proof of purchase may be required. This warranty does not apply to O-rings and Driver Blades or to
repair or replacement required due to misuse, abuse, normal wear and tear or repairs attempted or
made by other than our Service Centers or Authorized Service Stations.
ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE
OF PURCHASE.
To obtain information on warranty performance please write to: PORTER-CABLE CORPORATION,
4825 Highway 45 North, Jackson, Tennessee 38305; Attention: Product Service. THE FOREGOING
OBLIGATION IS PORTER-CABLE'S SOLE LIABILITY UNDER THIS OR ANY IMPLIED WARRANTY
AND UNDER NO CIRCUMSTANCES SHALL PORTER-CABLE BE LIABLE FOR ANY INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied
warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
This warranty gives you specific legal rights and you may also have other legal rights which vary
from state to state.
12

PORTER-CABLE • DELTA SERVICE CENTERS
(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)
(CENTRE DE SERVICE PORTER-CABLE =DELTA)
Parts and Repair Service for Porter-Cable •Delta Power Tools are Available at These Locations
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable •Delta)
(Locations oe vous trouverez les pi_ces de rechange n_cessaires ainsi qu'un service d'entretien)
ARIZONA GEORGIA MINNESOTA Cleveland 44125
Tempe 85282 (Phoenix) Forest Park 30297 (Atlanta) Minneapolis 55429 8001 Sweet Valley Drive
2400 West Southern Avenue 5442 Frontage Road, 5522 Lakeland Avenue North Unit #19
Suite 105 Suite 112 Phone: [phone] Phone: [phone]
Phone: [phone] Phone: [phone] Fax: [phone] Fax: [phone]
Fax: [phone] Fax: [phone] MISSOURI OREGON
CALIFORNIA ILLINOIS North Kansas City 64116 Portland 97230
Ontario 91761 (Los Angeles) Addison 60101 (Chicago) 1141 Swift Avenue 4916 NE 122 nd Ave,
3949A East Guasti Road 400 South Rohlwing Rd, Phone: [phone] Phone: [phone]
Phone: [phone] Phone: [phone] Fax: [phone] Fax: [phone]
Fax: [phone] Fax: [phone] St, Louis 63119 PENNSYLVANIA
San Diego 92111 Woodridge 60517 (Chicago) 7574 Watson Road Willow Grove 19090 (Philadelphia)
7638 Clairemnot Blvd. 2033 West 75th Street Phone: [phone] North York Road
Phone: [phone] Phone: [phone] Fax: [phone] Phone: [phone]
Fax: [phone] Fax: [phone] Fax: [phone]
NEW YORK
San Leandro 94577 (Oakland) MARYLAND Flushing 11365-1595 (N.Y.C.) TEXAS
3039 Teagarden Street EIkridge 21075 (Baltimore) 175-25 Horace Harding Exp.% Carrollton 75006 (Dallas)
Phone: [phone]-102 Washington Blvd, Phone: [phone] Interstate 35 N, Suite 112
Fax: [phone] Phone: [phone] Fax: [phone] Phone: [phone]
Fax: [phone] Fax: [phone]
COLORADO NORTH CAROLINA
Arvada 80003 (Denver) MASSACHUSETTS Charlotte 28270 Houston 77043
8175 Sheridan Blvd., Unit S Franklin 02038 (Boston) 9129 Monroe Road, Suite 115 4321 Sam Houston Parkway, West
Phone: [phone] Franklin Industrial Park Phone: [phone] Suite 180
Fax: [phone]E Constitution Blvd, Fax: [phone] Phone: [phone]
Phone: [phone] Fax: [phone]
FLORIDA Fax: [phone] OHIO
Davie 33314 (Miami) Columbus 43214 WASHINGTON
4343 South State Rd, 7 (441) MICHIGAN 4560 Indianola Avenue Auburn 98001(Seattle)
Unit #107 Madison Heights 48071 (Detroit) Phone: [phone] West Valley HWY, North
Phone: [phone] Stephenson Highway Fax: [phone] Building D, Suite 111
Fax: [phone] Phone: [phone] Phone: [phone]
Fax: [phone] Fax: [phone]
Tampa33609
4538W, Kennedy Boulevard
Phone:[phone]
Fax:[phone]
Authorized Service Stations are located in many large cities. Telephone [phone] or 731-541-6042 for assistance locating one. Parts and
accessories for Porter-Cable * Delta products should be obtained by contacting any Porter-Cable * Delta Distributor, Authorized Service
Center, or Porter-Cable * Delta Factory Service Center. if you do not have access to any of these, call 888-848-5175 and you will be directed to
the nearest Porter-Cable * Delta Factory Service Center. Las Estaciones de Servicio Autorizadas est&n ubicadas en muchas grandes ciudades.
Uame a1800-487-8665 5 al 731-541-6042 para obtener asistencia a fin de Iocalizar una. Las piezas y los accesorios para los productos Porter-
Cable * Delta deben obtenerse poni6ndose en contacto con cualquier distribuidor Porter-Cable * Delta, Centro de Servicio Autorizado o Centro
de Servicio de F&brica Porter-Cable * Delta. Si no tiene acceso a ninguna de estas opciones, llame a1888-848-5175 y le dirigiran al Centro de
Servicio de F&brica Porter-Cable * Delta m&scercano. Des centres de service agr66s sont situ6s dans beaucoup de grandes villes. Appelez au
800-487-8665 ou au 731-541-6042 pour obtenir de I'aide pour en rep6rer un. Pour obtenir des pi6ces et accessoires pour les produits Porter-
Cable * Delta,s'adresser &tout distributeur Porter-Cable * Delta,centre de service agr66 ou centre de service d'usine Porter-Cable * Delta. Si
vous n'avez acc_s &aucun de ces centres, appeler le 888-848-5175 et on vous dirigera vers le centre de service d'usine Porter-Cable * Delta le
plus proche. CANADIAN PORTER-CABLE * DELTA SERVICE CENTERS
ALBERTA MANITOBA QUI_BEC
Bay 6, 2520-23rd St. NE 1699 Dublin Avenue 1515 Ave.
Calgary, Alberta Winnipeg, Manitoba St-Jean Baptiste, Suite 160
T2E 8L2 R3H 0H2 Qu6bec, P.Q.
Phone: [phone] Phone: [phone] G2E5E2
Fax: [phone] Fax: [phone] Phone: [phone]
BRITISH COLUMBIA ONTARIO Fax: [phone]
8520 Baxter Place 505 Southgate Drive 1447, Begin
Burnaby, B.C Guelph, Ontario St-Laurent, (Mtl), P.Q.
V5A 4T8 N1H 6M7 H4R lV8
Phone: [phone] Phone: [phone] Phone: [phone]
Fax:/604 / 420-3522 Fax: [phone] Fax:/514 / 336-3505
The following are trademarks of PORTER-CABLE * DELTA (Las siguientes son marcas registradas de PORTER-CABLE * DELTA S.A.) (Les
marques suivantes sont des marques de fabriquant de la PORTER-CABLE * DELTA): Auto-Set ®,BAMMER®,B.O.S.S. _, Builder's Saw®,
Contractor's Saw®,Contractor's Saw II_M,Delta®,DELTACRAFT_,DELTAGRAM_, Delta Series 2000TM, DURATRONIC _M,Emc 2TM,FLEX®,Flying
Chips _M,FRAME SAW®, Grip Vac _M,Homecraft ®,INNOVATION THAT WORKS ®,Jet-Lock ®, JETSTREAM ®,'kickstand e, LASERLOCe,MICRO-
SET®,Micro-Set ®,MIDI LATHE®,MORTEN _M,NETWORK M,OMNIJIG ®,POCKET CUTTER e, PORTA-BAND e, PORTA-PLANE ®,PORTER-
CABLEe&(design), PORTER-CABLEePROFESSIONAL POWER TOOLS, PORTER-CABLE REDEFINING PERFORMANCE M, Posi-Matic ®, Q-
3e&(design), QUICKSAND®&(design), QUICKSET _M,QUICKSET II®,QUICKSET PLUS M,RIPTtDEM&(design), SAFE GUARD IIe, SAFE-LOC ®,
Sanding Cente¢_, SANDTRAPe&(design), SAW BOSS®,Sawbuck _M,Sidekicke, SPEED-BLOCe,SPEEDMATICe, SPEEDTRONIC®,STAIR EASEe,
The American Woodshop®&(design), The Lumber Company®&(design), THE PROFESSIONAL EDGEe,THE PROFESSIONAL SELECTs,THIN-
LINE_M,TIGERe,TIGER CUB e,TIGER SAW®,TORQBUSTER e, TORQ-BUSTER e,TRU-MATCH TM, TWIN-LITE e, UNIGUARD ®, Unifence ®,
UNIFEEDERTM ,Unihead®, Uniplane _,Uniripe,Unisaw_, Univisee,Versa-Feeder_,VERSA-PLANE®,WHISPER SERIES®,
WOODWORKER'S CHOICETM,
Trademarks noted with TMand ® are registered in the United States Patent and Trademark Office and may also be registered in other countries
LesMarces Registrades con el signo de M y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y tambi6n pueden
estar registradas en otros paises Marques d6pos6es, indiqu6es par la lettre _Met ®, sont d6pos6es au Bureau des brevets d'invention et
marques d6pos6es aux Etats-Unis et pourraient _tre d6pos6es aux autres pays. Printed in U.S.A. PC-0104-151