Porter-Cable FR350A User manual
1 - ENG FR350A
ROUND HEAD
FRAMING NAILER
Cloueuse de charpente à
clous à tête ronde
Clavadora para
estructuras con
cabezal redondo
www.deltaportercable.com
INSTRUCTIVO DE OPERACIÓN, CENTROS
DE SERVICIO Y PÓLIZA DE GARANTÍA.
LÉASE ESTE INSTRUCTIVO
ANTES DE USAR EL PRODUCTO.
Française : Page 17
Español: Página 34
Instruction manual
Manuel d'instructions
Manual de'instrucciones
2 - ENG
IMPORTANT SAFETY INSTRUCTIONS
FOR PNEUMATIC TOOLS
save these instructions
When using any pneumatic tool, all safety precautions, as outlined below,
should be followed to avoid the risk of death or serious injury. Read and understand all
instructions before operating the tool.
DEFINITIONS - SAFETY GUIDELINES
The definitions below describe the level of severity for each signal word. Please read the
manual and pay attention to these symbols.
Indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Used without the safety alert symbol indicates potentially hazardous
situation which, if not avoided, may result in property damage.
glasses with side shields. These safety glasses must
conform to ANSI Z87.1 requirements (approved glasses
have “Z87” printed or stamped on them). It is the employer’s
responsibility to enforce the use of eye protection equipment
by the tool operator and other people in the work area.
(Fig. A)
to appropriate setting.
protection during use. Under some conditions and
to hearing loss. (Fig. A)
an air compressor can rust and damage the internal
(Fig. B)
[Not to exceed 120
psi (8.3 bar).] Do not connect the tool to a compressor
rated at over 175 psi. The tool operating pressure must
never exceed 175 psi even in the event of regulator failure.
(Fig. C)
(Fig. D)
70 psi
4.9 bar
Fig. C
Fig. B
Fig. A
Fig. D
3 - ENG
Never use combustible
gases or any other reactive gas as a power source for this
tool. Danger of explosion and/or serious personal injury
may result. (Fig. E)
compressor when the tool is disconnected. (Fig. F)
passing the tool to another operator. Do not carry
tool to another work area in which changing location
air supply. If the contact trip is adjusted when the tool
is connected to the air supply and nails are loaded,
accidental discharge may occur. (Fig. G)
•
connected to the air supply. Do not load fasteners with
trigger or safety depressed to prevent unintentional firing
of a fastener.
Do not tape or tie trigger or contact trip in the on
position. Do not remove spring from contact trip. Make
daily inspections for free movement of trigger and contact
trip. Uncontrolled discharge could result.
•
Leaking
air, damaged parts or missing parts should be repaired or
replaced before use. Refer to Repairs. (Fig. H)
Fig. I)
time. No horseplay! Work safe! Respect the tool as a
working implement. (Fig. J)
•
operating a power tool. Distractions can cause you to
lose control. When tool is not in use, it should be locked
in a safe place, out of the reach of children.
Fig. E
Fig. F
Fig. I
Fig. J
Fig. G
Fig. H
4 - ENG
Accidental discharge could result.
at all times. Loss of balance may cause personal injury.
(Fig. K)
Do not discharge
Do not use the body of the tool
or top cap as a hammer. Discharged fasteners may follow
unexpected path and cause injury. (Fig. L)
(Fig. M)
Maintenance and Repairs
tool.
Be
injuring you or a co-worker. Be aware that the nail
may follow the grain of the wood (shiner), causing it
to protrude unexpectedly from the side of the work
material. Drive the nail perpendicular to the grain to
reduce risk of injury. (Fig. N)
or with the tool at too steep an angle. Personal injury
nails may result. (Fig. O)
A protruding nail may cause injury.
compressor is set so that nails are set into the
material and not pushed completely through. (Fig. P)
area. Hold workpiece with clamps when necessary to
Be sure
the workpiece is properly secured before pressing the
nailer against the material.The contact trip may cause
the work material to shift unexpectedly. (Fig. Q)
Fig. K
Fig. L
Fig. M
Fig. N
Fig. O
5 - ENG
Driving a nail into
another nail may also cause a spark. (Fig. R)
cap when working in restricted areas. Sudden recoil
nailing into hard or dense material. (Fig. S)
maintain control while allowing
or triggering options.
BUMP OR CONTACT ACTUATION TRIGGER
trip is allowed to accidentally re-contact the
(Fig. T)
TO AVOID DOUBLE FIRES:
• Do not engage the tool against the work surface
with a strong force.
• Allowthetooltorecoilfullyaftereachactuation.
• Usesequentialactiontrigger.
control.
SEQUENTIAL ACTION TRIGGER
against the workpiece.
DEPTH ADJUSTMENT:
• Disconnectairsupply.
• Avoidcontactwithtriggerduringadjustments.
work areas.
injury. (Fig. U)
sense when operating a power tool. Do not use tool
A moment of inattention while operating power tools may
result in serious personal injury.
Fig. Q
Fig. R
Fig. S
Fig. P
Fig. T
6 - ENG
Use of this product will expose you to chemicals
known to the State of California to cause cancer, birth defects
and other reproductive harm.
Allowing
dust to get into your mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.
Use of this tool can generate and/or disburse
dust, which may cause serious and permanent respiratory or other injury. Always use
NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct
particles away from face and body. Always operate tool in well-ventilated area and
provide for proper dust removal. Use dust collection system wherever possible.
ALWAYS USE SAFETY GLASSES. Everyday eyeglasses are NOT safety
glasses. Also use face or dust mask if operation is dusty. ALWAYS WEAR CERTIFIED
SAFETY EQUIPMENT:
• ANSIZ87.1eyeprotection(CAN/CSAZ94.3),
• ANSIS12.6(S3.19)hearingprotection,
• NIOSH/OSHArespiratoryprotection.
ImportantSafetyInstructions.
save these instructions
NAIL SPECIFICATIONS
Nails 0.113"–0.148" (2.87–3.76 mm)
diameter, plastic collated round head framing nails
Lengths 2"–3-1/2"(50–90mm)
Angle 22º
Air Inlet 1/4" NPT (6.4 mm)
Fig. U
7 - ENG
TOOL PARTS
A
F
G
C
B
E
A. Exhaust deflector
B. Selectable trigger
C. Air Inlet with quick
connect coupler
D. Magazine
E. Nail follower
F. Safety contact trip
with No-mar pad
G. Depth adjustment
wheel
H. Pusher release
I. Pusher
H
D
I
ASSEMBLY
TRIGGER
Keep fingers AWAY from trigger when not driving fasteners to avoid
accidental firing. Never carry tool with finger on trigger. In bump action mode (contact
actuation mode) tool will fire a fastener if safety is bumped while trigger is depressed.
The FR350A is equipped with a selectable trigger. This trigger allows the operator to select
either single sequential action trigger mode or bump action trigger mode. In accordance
with the ANSI Standard SNT-101-2002, the trigger is assembled in the single sequential
action trigger mode. To change the trigger mode, see Actuating Tool instructions in the
Operation section of the manual.
IMPORTANT: Atrigger, which will limit the tool to only, is
availablefree-of-chargebycalling1-800-321-9443intheUnitedStatesandCanada
or 001-731-660-9374 outside the United States and Canada, and providing tool
model number, type, serial number, etc. For identification purposes: the
actuation trigger is red.
AIR FITTING
Thetoolisequippedwitha1/4"(6.4mm)malequickconnectorcoupling.A3/8"(9.5mm)
male quick connector coupling is available from PORTER-CABLE and may be used when
a 1/4" (6.4 mm) supply line is not available.
8 - ENG
NOTE: A 3/8" (9.5 mm) supply line (and fittings) are required for maximum tool
performance. IMPORTANT: Always use couplings that relieve all pressure from the tool
when it is disconnected from the power supply. Always use hose connectors that shut
off air supply from compressor when the tool is disconnected.
1. Wrap the male end of the fitting with thread seal tape prior to assembly to eliminate
air leaks.
2. To install a 1/4" (6.4 mm) fitting: screw it directly into the air inlet and tighten firmly.
NOTE: If an adapter is in the air inlet, remove it prior to inserting the fitting.
3. Toinstalla3/8"(9.5mm)fitting:screwthefittingintothe3/8"(9.5mm)adapterand
then into the air inlet of the tool and tighten firmly.
OPERATION
PREPARING THE TOOL
Read the section titled
Tools at the beginning of this manual. Always wear eye and ear protection when
operating this tool. Keep the nailer pointed away from yourself and others. For safe
operation, complete the following procedures and checks before each use of the nailer.
To reduce the risk of damage to the tool, only use PORTER-CABLE
pneumatic tool oil or a non-detergent S.A.E. 20 weight oil. Oil with additives or detergent
will damage tool parts.
1. Before you use the nailer, be sure that the compressor tanks have been properly
drained.
2. Lubricate tool:
a. Use PORTER-CABLE pneumatic tool oil or a non-detergent S.A.E. 20 weight oil.
DO NOT use detergent oil or additives as they will damage O-rings and rubber
parts.
b. Use a filter and regulator when possible.
c. Add 5 to 7 drops of oil in the air fitting a least twice a day.
3. Wear eye and ear protection.
4. Ensure magazine is empty of all fasteners.
5. Check for smooth and proper operation of contact trip. Do not use tool if assembly
is not functioning properly. NEVER tamper with the contact trip. NEVER use a tool
that has the contact trip restrained in the actuated position.
6. Check air supply: Ensure air pressure does not exceed recommended operating
limits;70to120psi,(4.9to8.3bar,5to8.5kg/cm2).
7. Keep tool pointed away from yourself and others.
8. Connect air hose.
9. Checkforaudibleleaksaroundvalvesandgaskets.Neveruseatoolthatleaksor
has damaged parts.
Keep the tool pointed away from yourself and others. Serious personal
injury may result.
9-ENG
Never load nails with the contact trip or trigger activated. Personal injury
may result.
DO NOT load fasteners strip into magazine backwards.
1. Read all before using tool.
2. Connect the tool to air supply.
NOTE: See icon (K) for fastener direction.
3. Insert fasteners (L) into T-slot (J) at the rear of the magazine (E) past the nail follower
(E). NOTE: Magazine will hold two full fastener strip.
D
Fig. 2
KJ
L
E
L
4. Depress pusher release (H) and pull pusher (I) back until the nail follower (E) falls
behind the fasteners.
HI
L
Fig. 4
NOTE: Do not allow the pusher to snap forward against the nail strip, allowing this to
happen could damage the nail collation.
NOTE: This tool has a dry fire lock out device which will not allow the tool to fire when
the fastener quantity in the magazine is reduced to four. When unloading and loading the
magazine always make sure these four nails have been removed from the magazine. If
the nails are not removed from the magazine and the tool is reloaded and fired the nails
will cause the tool to jam.
ACTUATING TOOL
To reduce the risk of injury, wear proper eye [ANSI Z87.1 (CAN/
CSAZ94.3)]andhearingprotection[ANSIS12.6(S3.19)]whenoperatingthistool.
The tool can be actuated using one of two modes: single sequential action trigger mode
and bump action trigger mode.
10 - ENG
A fastener will fire each time the trigger
O
is depressed as long as the contact trip remains
depressed which could result in accidental firing.
The sequential action trigger’s intended use is for
intermittent fastening where very careful and accurate
placement is desired. Push selectable trigger button (O)
from back of trigger and turn indicator to the position.
The tool is now ready to operate in the single sequential
action trigger mode
1. Depress the contact trip firmly against the work surface.
2. Depress the trigger.
A nail will fire each time the trigger is depressed as long as the contact
trip remains depressed.
Bump action trigger -
The bump action trigger’s intended use is for rapid fastening on flat, stationary
surfaces.
Using the bump action trigger, two methods are
O
available: place actuation andPush
selectable trigger button (O) from back of trigger and
turn indicator to the position. The tool is now ready
to operate in the bump action trigger mode
To operate the tool using the PLACE ACTUATION
method:
1. Depress the contact trip against the work surface.
2. Depress the trigger.
To operate the tool using the BUMP ACTUATION method:
1. Depress the trigger.
2. Push the contact trip against the work surface. As long as the trigger is depressed,
the tool will fire a fastener every time the contact trip is depressed. This allows the
user to drive multiple fasteners in sequence.
To reduce risk of serious injury from accidental actuation when
attempting to adjust depth, ALWAYS:
• Disconnectairsupply.
• Avoid contact with trigger during
G
adjustments.
The depth that the fastener is driven can be
adjusted using the depth adjustment wheel (G).
The depth of drive is factory adjusted. Test
fire a fastener and check depth. If a change is
desired:
1. To drive the nail shallower, rotate the depth
setting wheel (G) to the right.
11 - ENG
2. To drive a nail deeper, rotate the depth setting wheel (G) to the left.
The adjustment knob has detents every 1/4 turn. Test fire another fastener and check
depth. Repeat as necessary to achieve desired results. The amount of air pressure
required will vary depending on the size of the fastener and the material being fastened.
Experiment with the air pressure setting to determine the lowest setting that will
consistently perform the job at hand.
Air pressure in excess of that required can cause premature wear and/
or damage to the tool.
Adjust directional exhaust deflector (A), so the exhaust air
A
blast will be directed away from the operator. The exhaust
deflector provides eight detented positions for directing
the exhaust blast away from the operator. Grasp the
deflector and rotate it to the desired position for the
current application.
Disconnect tool from air supply before removing or re-installing no-mar
pad.
The no-mar pad (F) is provided to reduce marring of the work surface. The no-mar pad
can be removed, and stored inside the bracket (M), to provide increased depth-of-drive
for toe-nailing applications.
F
M
Disconnect air line from tool and remove fasteners from magazine
before making adjustments or personal injury may result.
If a nail becomes jammed in the nosepiece, keep the tool pointed away from you and
follow these instructions to clear:
1. Disconnect the air supply from the tool.
2. Depress pusher release (H) and slide pusher (I) all the way to the front of the
magazine.
12 - ENG
3. Depress nail follower (E) and slide fasteners from magazine.
H
IE
4. If nail is jammed between the driver and nose casting force driver blade back to the
top using a 1/4" (6.4 mm) punch and hammer. When the nail is released it will fall
free or can be removed using pliers.
N
5. If nail still can not be removed, remove the magazine:
a. Remove screws (N).
b. Remove magazine.
c. Remove bent nail.
d. Reassemble in reverse order.
NOTE: Should nails continue to jam frequently in nosepiece, have tool serviced by an
authorized PORTER-CABLE service center.
When operating tools at temperatures below freezing:
1. Make sure compressor tanks have been properly drained prior to use.
2. Keep tool as warm as possible prior to use.
3. Make certain all fasteners have been removed from magazine.
4. Put 5 to 7 drops of PORTER-CABLE pneumatic tool oil in the air inlet.
5. Lower air pressure to 80 psi or less.
6. Reconnect air and load nails into magazine.
7. Actuate the tool 5 or 6 times into scrap lumber to lubricate O-rings.
8. Turn pressure up to operating level (not to exceed 120 psi) and use tool as normal.
9. Re-lubricateatleastoncedaily.
10. Always drain the compressor tanks at least once a day.
Tool should operate normally. However, keep tool out of direct sunlight as excessive
heat can deteriorate bumpers, O-rings and other rubber parts resulting in increased
maintenance.
13 - ENG
MAINTENANCE
DAILY MAINTENANCE CHART
ACTION
Lubricate tool with 5-7
drops of PORTER-CABLE
pneumatic tool oil
Prevents failure
of o-rings Insert drops into air fitting
on end cap of tool
Drain compressor tanks
and hoses daily Prevents accumulation
of moisture in
compressor and nailer
Open petcocks or
other drain valves on
compressor tanks. Allow
any accumulated water
to drain from hoses
Clean magazine, magazine
release and contact
trip mechanism.
Permits smooth
operation of magazine,
reduces wear and
prevents jams.
Blow clean with
compressor air. The
use of oils, lubricants
periodically or solvents is
not recommended as they
tend to attract debris.
Before each use, check
to insure all screws,
nuts and fasteners are
tight and undamaged.
Prevents jams, leaks
and premature failure
of tool parts.
Tighten loose screws
or other fasteners using
the appropriate hex
wrench or screwdriver.
CLEANING
Never use solvents or other harsh chemicals for cleaning the non-
metallic parts of the tool. These chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
REPAIRS
For assistance with your tool, visit our website at www.deltaportercable.com for a list of
service centers, or call the PORTER-CABLE Customer Care Center at (888) 848-5175.
SERVICE
REPLACEMENT PARTS
Use only identical replacement parts. For a parts list or to order parts, visit our service
website at www.deltaportercableservicenet.com. You can also order parts from your
nearest PORTER-CABLE Factory Service Center or PORTER-CABLE Authorized
Warranty Service Center. Or, you can call our Customer Care Center at (888) 848-5175.
SERVICE AND REPAIRS
All quality tools will eventually require servicing and/or replacement of parts. For information
about PORTER-CABLE, its factory service centers or authorized warranty service centers,
visit our website at www.deltaportercable.com or call our Customer Care Center at (888) 848-
5175. All repairs made by our service centers are fully guaranteed against defective material
and workmanship. We cannot guarantee repairs made or attempted by others.
14 - ENG
You can also write to us for information at PORTER-CABLE, 4825 Highway 45 North, Jackson,
Tennessee 38305 - Attention: Product Service. Be sure to include all of the information shown
on the nameplate of your tool (model number, type, serial number, etc.).
ACCESSORIES
Since accessories, other than those offered by PORTER-CABLE, have not
been tested with this product, use of such accessories with this tool could be hazardous. To
reduce the risk of injury, only PORTER-CABLE recommended accessories should be used
with this product.
A complete line of accessories is available from your PORTER-CABLE Factory Service Center
or a PORTER-CABLE Authorized Warranty Service Center. Please visit our Web Site www.
deltaportercable.com for a catalog or for the name of your nearest supplier.
PORTER-CABLE will repair, without charge, any defects due to faulty materials or
workmanship for three years from the date of purchase. This warranty does not cover
part failure due to normal wear or tool abuse. For further detail of warranty coverage
and warranty repair information, visit www.deltaportercable.com or call (888) 848-5175.
This warranty does not apply to accessories or damage caused where repairs have been
made or attempted by others. This warranty gives you specific legal rights and you may
have other rights which vary in certain states or provinces.
In addition to the warranty, PORTER-CABLE tools are covered by our:
PORTER-CABLE will maintain the tool and replace worn parts
caused by normal use, for free, any time during the first year after purchase.
If you are not completely satisfied with the per-
formance of your PORTER-CABLE Power Tool, Laser, or Nailer for any reason, you can
returnitwithin90daysfromthedateofpurchasewitha receiptforafullrefund–no
questions asked.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For
products sold in Latin America, see country specific warranty information contained in the
packaging, call the local company or see website for warranty information.
To register your tool for warranty service visit our website at www.deltaportercable.com.
If your warning labels become illegible or are missing, call (888) 848-5175 for a free
replacement.
15 - ENG
TROUBLESHOOTING GUIDE
MANY COMMON PROBLEMS CAN BE SOLVED EASILY BY UTILIZING THE CHART
BELOW. FOR MORE SERIOUS OR PERSISTENT PROBLEMS, CONTACT A PORTER-
CABLE SERVICE CENTER OR CALL 1 888 848-5175.
SYMPTOM PROBLEMS SOLUTIONS
Air leak near top of
tool or in trigger area Loose screws. Tighten screws.
Worn or damaged
o-rings or seals. Install Overhaul Kit.
Tool does nothing or
operates sluggishly Inadequate air supply. Verify adequate air supply.
Inadequate lubrication. Put 5 or 7 drops of
oil into air inlet.
Worn or damaged
o-rings or seals. Install Overhaul Kit.
Air leak near
bottom of tool Loose screws. Tighten screws.
Worn or damaged
o-rings or bumper. Install Overhaul Kit.
Tool jams frequently Incorrect fasteners. Verify approved fasteners
of correct size.
Damaged fasteners. Replace with undamaged
fasteners.
Magazine or nose screws loose Tighten screws.
Magazine is dirty. Clean magazine.
Driver tip is worn or
damaged. Install Driver Maintenance Kit.
Other Contact a PORTER-
CABLE Authorized
Warranty Service Center
TOOL SPECIFICATIONS
Height (inch/meter) 13.8/0.35
(inch/meter) 4.6/0.15
Length (inch/meter) 21.2/0.54
(lbs/kg) 7.7/3.5
Recommended Operating Pressure 70-120 psi (4.8 to 8.3 bar)
9.76SCF
Loading capacity 63–64 nails
16 - ENG
Portable
Handcarry
5.5 HP Gas
2 HP Elec.
8 HP Gas
Industrial
NUMBER OF TOOLS CONNECTED TO COMPRESSOR
2
4
NR
NR
NR NR
NR NR
NR NR
NR
Not Recommended
17 - FR
CONSIGNES DE SÉCURITÉ IMPORTANTES A
POUR LES OUTILS PNEUMATIQUES
conservez ces directives
lorsqu’on utilise un outil pneumatique quelconque, respecter
toutes les mesures de sécurité, décrites ci-après, pour éviter un risque de décès ou de
blessures graves. Lire et assimiler toutes les directives avant d’utiliser l’outil.
MESURES DE SÉCURITÉ - DÉFINITIONS
Les définitions ci-dessous décrivent le niveau de gravité pour chaque symbole.
Veuillez lire le mode d’emploi et porter une attention particulière à ces symboles.
Indique une situation dangereuse imminente qui, si elle n’est pas
évitée,
causera
Indique une situation potentiellement dangereuse qui, si elle
n’est pas évitée,
pourrait
se solder par un
.
Indique une situation potentiellement dangereuse qui, si elle n’est
pas évitée
pourrait
se solder par
.
Utilisé sans le symbole d’alerte à la sécurité, indique une situation
potentiellement dangereuse qui, si elle n'est pas évitée
pourrait
se solder
par des
dommages à la propriété.
Ces lunettes de sécurité
doivent être conformes à la norme ANSI Z87.1 (les lunettes
approuvées portent l’inscription imprimée ou estampillée
« Z87 »). L’employeur a la responsabilité d’imposer le port
d’un équipement de protection oculaire par l’opérateur de
l’outil et toute personne se trouvant dans la zone immédiate
de travail. (fig. A)
(fig. A)
(fig. B)
Ne pas
raccorder l’outil à un compresseur d’une puissance nominale supérieure à 12,6 bars
(175 psi). La pression de fonctionnement de l’outil ne doit jamais excéder 12,6 bars
(175 psi) même dans l’éventualité d’une défaillance du régulateur. (fig. C)
Fig. A
Fig. B
70 psi
4.9 bar
Fig. C
18 - FR
(fig. D)
Ne jamais utiliser
de gaz combustibles ou tout autre type de gaz réactif
comme source d’énergie pour cet outil. Leur utilisation
représente un danger d’explosion et peut se solder par
des blessures corporelles graves. (fig. E)
(fig. F)
opérateur.
Un
déclenchement intempestif pourrait se produire lors du
réglage du déclencheur si l’outil est raccordé à la source
d’alimentation en air en présence de clous dans le
chargeur. (fig. G)
•
Ne
pas enfoncer la détente ou le mécanisme de sécurité lors
du chargement des attaches pour prévenir un clouage par
inadvertance.
maintenir en position de marche. Ne pas retirer le ressort du déclencheur. Inspecter
quotidiennement le bon fonctionnement de la détente et du déclencheur. Une
décharge non contrôlée pourrait survenir.
• Ne pas utiliser un outil si une partie
Les fuites d’air ainsi
que les pièces endommagées ou manquantes devraient être réparées ou remplacées
avant utilisation. Se reporter à la rubrique Réparations. (fig. H)
Fig. H
Fig. D
Fig. E
Fig. F
Fig. G
19-FR
(fig. I)
attaches.
Travailler en toute sécurité!
Traiter l’outil comme un instrument essentiel de travail.
(fig. J)
Verrouiller
l’outil dans un endroit sûr, hors de la portée des enfants
lorsqu’il n’est pas utilisé.
détente.
La non-utilisation du bouton pourrait se solder par une
décharge intempestive.
en tout temps. Une perte d’équilibre risque d’entraîner
une blessure corporelle. (fig. K)
Ne pas décharger les attaches
Ne pas utiliser
le corps de l’outil ou son couvercle supérieur comme
marteau. Les attaches éjectées peuvent suivre une
trajectoire inattendue et provoquer des blessures. (fig. L)
(fig. M)
Entretien et Réparations
Il est possible que le
clou suive le fil du bois et sorte inopinément sur le côté de la pièce. Enfoncer le clou
perpendiculairement au fil du bois pour réduire le risque de blessures. (fig. N)
(fig. O)
Fig. K
Fig. L
Fig. M
Fig. I
Fig. J
20 - FR
Un clou en saillie peut causer
poussés entièrement dans celui-ci. (fig. P)
mains et le corps de dangers potentiels. S’assurer
que la pièce est bien fixe avant d’appuyer la cloueuse
contre celle-ci. La force du déclencheur peut entraîner
le déplacement inopiné de la pièce. (fig. Q)
Une étincelle pourrait
également être produite si un clou est enfoncé sur un
autre clou. (fig. R)
(fig. S)
déclenchera.
options de déclenchement.
MODE DE DÉTENTE ACTIONNÉE PAR COUP OU PAR
CONTACT
On peut enfoncer
involontairement des clous si le déclencheur touche
de nouveau la pièce inopinément. (fig. T)
POUR ÉVITER LES DOUBLES
DÉCLENCHEMENTS :
• Nepaspresserl’outilcontrelapièceavectropde
force.
Fig. N
Fig. O
Fig. Q
Fig. R
Fig. S
Fig. P
Table of contents
Languages:
Other Porter-Cable Nail Gun manuals
Porter-Cable
Porter-Cable DA250B User manual
Porter-Cable
Porter-Cable FN250A User manual
Porter-Cable
Porter-Cable FCP350 User manual
Porter-Cable
Porter-Cable 894884-003 User manual
Porter-Cable
Porter-Cable CFN250 User manual
Porter-Cable
Porter-Cable PN650 User manual
Porter-Cable
Porter-Cable COIL350 User manual
Porter-Cable
Porter-Cable FM350A User manual
Porter-Cable
Porter-Cable PIN138-CA User manual
Porter-Cable
Porter-Cable DA250C User manual
Porter-Cable
Porter-Cable PCC790B User manual
Porter-Cable
Porter-Cable BN200B User manual
Porter-Cable
Porter-Cable PIN138 User manual
Porter-Cable
Porter-Cable FR350 User manual
Porter-Cable
Porter-Cable RN175B User manual
Porter-Cable
Porter-Cable PIN138 User manual
Porter-Cable
Porter-Cable FC350B User manual
Porter-Cable
Porter-Cable BN200C User manual
Porter-Cable
Porter-Cable PCC790 User manual
Porter-Cable
Porter-Cable FC350 User manual
Popular Nail Gun manuals by other brands
Metabo HPT
Metabo HPT NR 3675DD Instruction and safety manual
EXTOL PREMIUM
EXTOL PREMIUM 8894580 Translation of the original user manual
DeWalt
DeWalt XR Li-Ion DCN680D2 Original instructions
Performance Tool
Performance Tool M643 owner's manual
Hitachi
Hitachi VH650 - Fencing Nailer, Full Head instruction manual
Parkside
Parkside PET 25 B1 Operation and safety notes
