Porter-Cable PCE605 User manual

3.0 Amp Oscillating Multi-Tool
Instruction manual
Manuel d’instructions
Manual de’instrucciones
www.portercable.com
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y
PÓLIZA DE GARANTÍA.
ADVERTENCIA: LÉASE ESTE INSTRUCTIVO
ANTES DE USAR EL PRODUCTO.
CATALOG NUMBER
PCE605
PCE606
Outil oscillant polyvalent de 3,0 A
Multiherramienta oscilante de 3,0 Amperios
FITMENT
NIVERSAL
™
COMPATIBLE WITH:
CON| / AVEC
DEWALT®
Thank you for choosing PORTER-CABLE! To register your new product, go to:
www.portercable.com/ServiceAndSupport/ProductRegistration.aspx

2
SAFETY GUIDELINES - DEFINITIONS
It is important for you to read and understand this manual. The information it contains
relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols
below are used to help you recognize this information.
DANGER: Indicates an imminently hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided,
may result in minor or moderate injury.
NOTICE: Used without the safety alert symbol indicates potentially hazardous
situation which, if not avoided, may result in property damage.
GENERAL SAFETY RULES
WARNING: Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your mains-operated (corded) power
tool or battery-operated (cordless) power tool.
SAVE THESE INSTRUCTIONS
1) WORK AREA SAFETY
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,
ranges and refrigerators. There is an increased risk of electric shock if your body is
earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase the risk of electric shock.
e)
When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a ground fault circuit
interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective
equipment such as dust mask, nonskid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off position before
connecting to power source and/ or battery pack, picking up or carrying the
tool. Carrying power tools with your finger on the switch or energizing power tools
that have the switch on invites accidents.
d)
Remove any adjusting key or wrench before turning the power tool on. A wrench
or a key left attached to a rotating part of the power tool may result in personal injury.

3
e) Do not overreach. Keep proper footing and balance at all times. This enables
better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection facilities, ensure
these are connected and properly used. Use of dust collection can reduce dust-related hazards.
4) POWER TOOL USE AND CARE
a)
Do not force the power tool. Use the correct power tool for your application. The
correct power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power
tool that cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from the
power tool before making any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power
tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the power tool’s operation. If
damaged, have the power tool repaired before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits, etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended could
result in a hazardous situation.
5) SERVICE
a)
Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
SPECIFIC SAFETY RULES
• Hold power tool by insulated gripping surfaces, when performing an operation where the cutting
accessory may contact hidden wiring or its own cord. Cutting accessory contacting a “live” wire
may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
• Use clamps or another practical way to secure and support the work piece to a
stable platform. Holding the work by hand or against your body leaves it unstable and
may lead to loss of control.
• Disconnect power before using tool near live wires or where there may be hidden wiring.
Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live”
and could give the operator an electric shock.” Always check for hidden wiring, gas lines, or other
utilities before performing any material cutting or removal operations with the tool.
• Wait for the cutter to stop before setting the tool down. An exposed cutter may engage the
surface leading to possible loss of control and serious injury.
• Do not operate this tool for long periods of time. Vibration caused by the operating action of
this tool may cause permanent injury to fingers, hands, and arms. Use gloves to provide extra
cushion, take frequent rest periods, and limit daily time of use.
• Always hold the tool firmly with both hands for maximum control. Keep proper footing and
balance at all times. This enables better control of the power tool in unexpected situations.
• Do not restart the cutting operation in the work piece. Let the tool reach full speed and
carefully re-enter the cut.
• Do not “jam” the cut-off saw blade or apply excessive pressure. Do not attempt to make an
excessive depth of cut.
• Keep your hands away from cutting area. Do not reach under the material being cut.
• Do not use dull or damaged blades. Bent blade can break easily or cause kickback. Exercise
extreme caution when handling the accessories. The accessories are very sharp. Wear protective
gloves when changing cutting accessories. Accessories become hot after prolonged usage.
• Before scraping, check work piece for nails. If there are nails, either remove them or set
them well below intended finished surface. Striking a nail with accessory edge could cause
the tool to jump.

4
• Do not wet sand with this tool. Liquids entering the motor housing are an electrical shock hazard.
• Never work in area which is soaked with a liquid, such as a solvent or water, or dampened
such as newly applied wallpaper. There is an electrical shock hazard when working in such
conditions with a power tool and heating of the liquid caused by scraping action may cause
harmful vapors to be emitted from work piece.
• Do not use sandpaper intended for larger sanding pads. Larger sandpaper will extend
beyond the sanding pad causing snagging, tearing of the paper or kick-back. Extra paper
extending beyond the sanding pad can also cause serious lacerations.
WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses.
Also use face or dust mask. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:
•ANSI Z87.1 eye protection (CAN/CPA Z94.3),
•ANSI S12.6 (S3.19) hearing protection,
•NOSH/OSHA respiratory protection.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to the state of California to cause cancer, birth
defects or other reproductive harm. Some examples of these chemicals are:
•lead from lead-based paints,
 •crystalline silica from bricks and cement and other masonry products, and
•arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well ventilated area, and work with approved safety
equipment, such as those dust masks that are specially designed to filter out microscopic particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other
construction activities. Wear protective clothing and wash exposed areas with soap and
water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of
harmful chemicals.
WARNING: Use of this tool can generate and/or disperse dust, which may cause serious
and permanent respiratory or other injury. Always use NOSH/OSHA approved respiratory
protection appropriate for the dust exposure. Direct particles away from face and body.
WARNING: Always wear proper personal hearing protection that conforms to ANSI
S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product
may contribute to hearing loss.
PRECAUTIONS TO TAKE WHEN SANDING PAINT
1. Sanding of lead based paint is NOT RECOMMENDED due to the difficulty of controlling the
contaminated dust. The greatest danger of lead poisoning is to children and pregnant women.
2. Since it is difficult to identify whether or not a paint contains lead without a chemical
analysis, we recommend the following precautions when sanding any paint:
PERSONAL SAFETY
1. No children or pregnant women should enter the work area where the paint sanding is being
done until all clean up is completed.
2. A dust mask or respirator should be worn by all persons entering the work area. The filter
should be replaced daily or whenever the wearer has difficulty breathing. See your local
hardware store for the proper N.I.O.S.H. approved dust mask.
3. NO EATING, DRINKING or SMOKING should be done in the work area to prevent ingesting
contaminated paint particles. Workers should wash and clean up BEFORE eating, drinking
or smoking. Articles of food, drink, or smoking should not be left in the work area where dust
would settle on them.
ENVIRONMENTAL SAFETY
1. Paint should be removed in such a manner as to minimize the amount of dust generated.
2. Areas where paint removal is occurring should be sealed with plastic sheeting of 4 mils thickness.
3. Sanding should be done in a manner to reduce tracking of paint dust outside the work area.
CLEANING AND DISPOSAL
1. All surfaces in the work area should be vacuumed and thoroughly cleaned daily for the
duration of the sanding project. Vacuum filter bags should be changed frequently.
2. Plastic drop cloths should be gathered up and disposed of along with any dust chips or
other removal debris. They should be placed in sealed refuse receptacles and disposed of

5
through regular trash pick-up procedures. During clean up, children and pregnant women
should be kept away from the immediate work area.
3. All toys, washable furniture and utensils used by children should be washed thoroughly
before being used again.
SYMBOLS
• The label on your tool may include the following symbols. The symbols and their
definitions are as follows:
V..................volts A...................amperes
Hz................hertz W..................watts
min ..............minutes ................alternating current
or DC...direct current no.................no load speed
................Class I Construction ..................earthing terminal
(grounded) ................safety alert symbol
................Class II Construction opm...............oscillations per minute
(double insulated)
............ Read instruction manual before use ..................Use proper respiratory protection
................Use proper eye protection ..................Use proper hearing protection
•
When using an extension
cord, be sure to use one
heavy enough to carry the
current your product will
draw. An undersized cord will
cause a drop in line voltage
resulting in loss of power
and overheating. The table
shows the correct size to use
depending on cord length and
nameplate ampere rating. If
in doubt, use the next heavier
gauge. The smaller the gauge
number, the heavier the cord.
INTENDED USE
Detail Sanding
Sanding in extremely tight areas otherwise difficult to reach and require hand sanding. Select a
high oscillating frequency. Sand with continuous motion and light pressure. Applying excessive
pressure does not increase material removal; but will prematurely wear sanding sheets.
Flush Cutting
Remove excess wood from door jamb, window sill and/or toe kick. Removing excess
copper or PVC pipe.
Removal Work
Carpets & backing, old tile adhesives, caulking on masonry, wood and other surfaces.
Removal of Excess Materials
Tile grout, plaster, mortar splatters, concrete on tiles, sills.
Preparation of Surfaces
New floors and tiles.
Minimum Gauge for Cord Sets
Volts Total Length of Cord in Feet
120V 0-25 26-50 51-100 101-150
(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)
240V 0-50 51-100 101-200 201-300
(0-15,2m) (15,2-30,4m) (30,4-60,9m) (60,9-91,4m)
Ampere Rating
More Not more American Wire Gauge
Than Than
0 - 6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended
SAVE THESE INSTRUCTIONS

ASSEMBLY
WARNING: Disconnect the plug from the power source before making any
assembly, adjustments or changing accessories. Such preventive safety measures
reduce the risk of starting the tool accidentally.
WARNING: Risk of lacerations or burns. Do not touch the sharp edges of
accessories at any time. Do not touch work piece or blade immediately after operating
the tool. They can become very hot. Handle carefully. Always allow accessories and
work piece to cool before handling.
CAUTION: This multi-tool is compatible only with DeWalt®Universal FitmentTM
accessories and is not compatible with other Porter-Cable accessories.
INSTALLING/REMOVING
ACCESSORIES
The tool features an exclusive Tool Free System
for faster accessory changes and adjustments
without the need for wrenches or hex keys like
other oscillating tool systems.
•GraspthetoolandsqueezetheTool-Free
System’s accessory clamping lever as shown in
figure 2.
•Cleananyresidualdebrisfromthetoolshaftand
the accessory holder.
6
2
COMPONENTS
A.) On/Off switch
B.) Variable speed dial
C.) 10 foot cord
D.) Tool-Free accessory clamp
E.) Depth/Cut guide
*
F.)
Depth/Cut adjustment knob*
1
A
B
F
D
E
C
* Included with PCE605K only.

7
•Slidetheaccessorybetweentheshaftandtheaccessoryholdermakingsurethe
accessory engages all of the pins on the holder and is flush with the shaft (figure 3).
•Releasetheaccessoryclamplever.
•Someaccessories,suchasscrapersandbladescanbemountedatanangleif
required as shown in figure 4.
INSTALLING/REMOVING DEPTH/CUT BLOCK
The depth/cut guide allows you to precisely cut
material at a specified depth and more accurately
track a marked cut line.
•Attachthedepth/cutblockbyinsertingthetabson
the guide into the slots on the main body as shown in
figure 5.
•Securetheblocktothemainbodywiththesupplied
screw and tighten with the supplied hex wrench as
shown in figure 6.
INSTALLING/REMOVING
SANDING SHEETS
A diamond shaped platen uses a hook and loop
adhesion system to attach the sanding sheets. The
platen allows you to use it on large flat surfaces and
tight spots or corners.
•Attachthesandingplatenasdescribedunder
“Installing/Removing Accessories”.
•Aligntheedgesonthesandingsheet,withtheedge
of the sanding platen and press the sanding sheet
onto the platen as shown in figure 7.
•Firmlypressthebasewiththesandingsheet
attached against a flat surface and briefly switch the tool on. This provides for good
adhesion between the platen and the sanding sheet and also helps to prevent
premature wear.
•Whenthetipofthesandingsheetbecomesworn,detachthesheetfromtheplaten,
rotate and reapply.
34
5
6
7

OPERATION
SWITCH
CAUTION: Because the tool has a separate
speed dial for setting the speed (10,000 - 22,000
OPM), the tool will start at the speed where the
variable speed dial is set. Be sure switch is fully OFF
before plugging in the power cord.
•Pluginpowercord.
•ToturnthetoolON,holditasshowninfigure 8 and
push the slide switch forward.
•
To turn the tool OFF, push the slide switch backward.
VARIABLE SPEED DIAL
To operate the tool, select the speed setting you wish
with the speed dial, shown in figure 9, and slide the
ON/OFF switch forward. The speed setting can be
adjusted either with the tool on or off.
CAUTION: Because the tool has a separate
speed dial for setting the speed (10,000 - 22,000
OPM), the tool will start at the speed where the
variable speed dial is set. Be sure switch is fully OFF
before plugging in the power cord.
The numbered positions,1 through 6 inscribed on the variable speed dial, do not
indicate any precise speed but are good reference points. The higher the number, the
higher the tool speed.
The approximate speed at each setting is:
SPEED SETTING 1 2 3 4 5 6
APPROXIMATE SPEED 10,000 12,000 14,000 16,000 18,000 22,000
(Actual OPM’s on your tool may vary.)
Be sure to select the proper speed for your oscillating tool operation. If in doubt about
the proper speed for your operation, test the performance at low speed settings and
gradually increase until a comfortable speed is found.
PLUNGE CUTTING
WARNING: Hold saw firmly with both hands for all cutting operations.
WARNING: Inspect work area for hidden electrical wiring, gas pipes or
water pipes before making blind or plunge cuts. Failure to do so may result in
electrical shock, fire, explosion, or property damage.
WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety
glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR
CERTIFIED SAFETY EQUIPMENT.
WARNING: CUT HAZARD. Before cutting any type of material, be sure it is
firmly anchored or clamped to prevent slipping.
WARNING: CUT HAZARD. Let the tool work at its own pace. Do not overload,
blade breakage may occur.
TO MAKE A CUT:
•Clearlymarkthedesiredcuttingarea.
•Switchthetoolonbeforeapplyingpressureandslowlyfeedthebladeintothework
piece at the marked location as shown
in figure 13 .
WARNING: CUT HAZARD. Ensure the blade is not in contact with cutting
surface before starting saw.
•Advancethebladealongthecuttinglineuntilcutiscompleted.Don’tforcethetool;
let the blade cut at its own speed.
•Switchthetooloff.
NOTE:
Always use the appropriate type of saw blade for the work piece material and type of cut.
Cut only with sharp blades; they cut cleaner, faster and put less strain on the motor while cutting.
8
8
9

9
DEPTH GUIDE
This feature allows you to precisely cut material at a specified depth.
•
To use the depth
guide, insert the
guide as shown in
figure 10 into the
front slot on the
guide block.
•Adjustthelengthof
the guide by pulling
out or pushing
inward to achieve
the desired cut depth as shown
in figure 11 .
•Securetheguideinplacebyturningthedepth/cut
adjustment knob clockwise. To
release the guide turn the
depth/cut adjustment knob counterclockwise.
CUT GUIDE
This feature allows
you to more
accurately track a
marked cut line.
•
To use the cut
guide, insert the
guide as shown in
figure 12 into the
slots on the left and right sides of the guide block.
•Adjustthelengthoftheguidebypullingoutorpushinginwardtoachievethedesired
length as shown
in figure 13 .
•Securetheguideinplacebyturningthedepth/cut
adjustment knob clockwise. To
release the guide turn the
depth/cut adjustment knob counterclockwise.
SANDING
WARNING: Fire hazard. When working on metal surfaces, do not use a vacuum
cleaner because sparks are generated. Wear safety glasses and a dust mask. Due to the danger
of fire, do not use your sander to sand magnesium surfaces. Do not use for wet sanding.
NOTE: Do not rest fingers on platen during use. Move it in long sweeping strokes across the
surface, letting it do the work. Light pressure is all that is required for sanding. Excessive pressure
will slow the tool and produce inferior results. Check your work often, product is capable of
removing material rapidly. Excessive force will reduce the working efficiency and cause motor
overload. Replacing the sanding sheet regularly will maintain optimum working efficiency.
NOTE: Always ensure the work piece is firmly held or clamped to prevent movement. Any
movement of the material may affect the quality of the sanding finish.
HELPFUL HINTS
•Alwaysensuretheworkpieceisfirmlyheldorclampedtopreventmovement.Any
movement of the material may affect the quality of the cutting or sanding finish.
•Donotstartsandingwithouthavingthesandpaperattachedtosandingplaten.
•Usecoarsegritpapertosandroughsurfaces,mediumgritforsmoothsurfacesand
fine grit for the finishing surfaces. If necessary, first make a test run on scrap material.
•Excessiveforcewillreducetheworkingefficiencyandcausemotoroverload.
Replacing the accessory regularly will maintain optimum working efficiency.
•Donotallowthesandpapertowearaway,itwilldamagethesandingpad.
•Ifthetooloverheats,especiallywhenusedatlowspeed,setthespeedtomaximum
and run it with no load for 2-3 minutes to cool the motor. Avoid prolonged usage at very
low speeds. Always keep the blade sharp.
MAINTENANCE
CAUTION: Never use solvents or other harsh chemicals for cleaning the non-
metallic parts of the tool. Use only mild soap and damp cloth to clean the tool. Never let
any liquid get inside the tool; never immerse any part of the tool into a liquid.
13
1110
12

10
REPLACEMENT PARTS
Use only identical replacement parts. For a parts list or to order parts, visit our service website
at www.portercable.com. You can also order parts from your nearest PORTER-CABLE Factory
Service Center or PORTER-CABLE Authorized Warranty Service Center. Or, you can call our
Customer Care Center at [phone].
SERVICE AND REPAIRS
All quality tools will eventually require servicing and/or replacement of parts. For information about
PORTER-CABLE, its factory service centers or authorized warranty service centers, visit our
website at www.portercable.com or call our Customer Care Center at [phone]. All repairs
made by our service centers are fully guaranteed against defective material and workmanship. We
cannot guarantee repairs made or attempted by others.
You can also write to us for information at PORTER-CABLE, 4825 Highway 45 North, Jackson,
Tennessee 38305, [phone] - Attention: Product Service. Be sure to include all of the
information shown on the nameplate of your tool (model number, type, serial number, etc.).
A complete line of accessories is available from your PORTER-CABLE Factory Service
Center or a PORTER-CABLE Authorized Warranty Service Center. Please visit our
Web Site www.portercable.com for a catalog or for the name of your nearest supplier.
ACCESSORIES
WARNING: Since accessories, other than those offered with DeWalt®Universal
FitmentTM, have not been tested for this product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only PORTER-CABLE recommended
accessories should be used with this product.
A complete line of accessories is available from your PORTER-CABLE Factory Service
Center or a PORTER-CABLE Authorized Warranty Service Center. Please visit our
Web Site www.portercable.com for a catalog or for the name of your nearest supplier.
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
•Reorientorrelocatethereceivingantenna.
•Increasetheseparationbetweentheequipmentandreceiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment. This Class B
digital apparatus complies with Canadian ICES-003.
TROUBLESHOOTING
Problem Possible Cause Possible Solution
• Unitwillnotstart. •Cordnotpluggedin. •Plugtoolintoaworkingoutlet.
  •Circuitfuseisblown. •Replacecircuitfuse.(Ifthe
product repeatedly causes the
circuit fuse to blow, discontinue
use immediately and have it
serviced at a Porter Cable
service center or authorized
servicer.)
 •Circuitbreakeristripped. •Resetcircuitbreaker.(Ifthe
product repeatedly causes the
circuit breaker to trip,
discontinue use immediately
and have it serviced at a Porter
Cable service center or
authorized servicer.)
 •Cordorswitchisdamaged. •Havecordorswitchreplaced
at a Porter Cable Service
Center or Authorized Servicer
For assistance with your product, visit our website at www.portercable.com for a list of
service centers, or call the PorterCable Customer Care Center at [phone].