Portfolio 4193 User manual

Motion Sensing
Diecast Lantern
PF-4190 Series
Features
• Light comes on when motion is detected.
• Automatically turns light off.
• Dusk Accent lighting.
• Photocell keeps the light off during daylight
hours.
Requirements
• The Light Control requires 120 volts AC.
• If you want to use Manual Mode, the control
must be wired through a switch.
• Some codes require installation by a
qualified electrician.
© 2006 DESA Specialty Products™ 598-1167-03
OPERATION
* resets to Auto Mode at dawn.
Set the ON-TIME switch
on the bottom of the cover
plate to TEST. TEST 1 5 10 MIN
Set ON-TIME switch to 1,
5, or 10 minutes.
1 Second
OFF then...
Manual mode only works at
night because daylight re-
turns the sensor to AUTO.
Flip the light switch off for
one second then back on to
toggle between AUTO and
MANUAL MODE.
Manualmodeworksonlywith
the ON-TIME switch in the 1,
5, or 10 position.
... back on.
Mode Switching Summary
DualBrite®Dimmer Control
Light comes on half bright for selected time
after dusk (3 hr., 6 hr., until dawn). If motion
is sensed, the light turns on full bright for the
ON-TIME (1, 5, or 10 minutes) then returns
to dim mode.
This package includes:
• Lantern
• Easy to use universal mounting bracket
(X-Bar)
• Mounting hardware
• Wire nuts
ON-TIME Switch at 1,
5, or 10 minutes
Flip light switch
off for one second
then back on*
* If you get confused while switching modes,
turn the power off for one minute, then back
on.After the calibration time the control will
be in the AUTO mode.
MANUAL MODE
AUTO
TEST
Note: When first turned on wait about 1 1/2
minutes for the circuitry to calibrate.
TEST
AUTO
MANUAL MODE
TEST 1 5 10 MIN
Before installation, record the model
number from back of fixture below.
Attach receipt in case of possible war-
ranty issues.
Mode: On-Time Works: Day Night
Test 5 Seconds x x
Auto 1, 5, or 10 Min x
Manual To Dawn* x
Accent 3, 6 Hr, to Dawn x

2598-1167-03
INSTALLATION
Forbestperformance,mountthefixtureabout
6 feet (1.8 m) above the ground.
1. Remove
two nuts.
2. Remove
X-Bar.
Junction
Box
5. Attach X-Bar to
junction box
Due to the size and weight of the fixture, you
mayfindithelpfultohaveanassistantholdthe
fixture in place while connecting the wires.
WIRING
One Motion Light
BLACK
WHITE
Two Motion Lights
BLACK
BLACK
WHITE
Recommended Grounding Method
Use a green ground “pigtail” (not provided) and
twist one end together with the bare fixture wire
and the box ground wire. Secure with a wire
connector. Secure the other end of the “pigtail”
with the GND screw on the X-bar.
❒Twist the junction box wires and the
fixture wires together as shown below.
Secure with wire connectors. If you have
a metal junction box, you may not need
the green “pigtail”.If you are unsure about
the grounding method, consult your local
building code.
CAUTION: DO NOT connect the RED
wire unless you want to control other
lights from the motion sensor.
Black to black White to white
MAX
MIN
3. Tighten screws
finger tight.
SENSITIVITY
4. Set sensitivity on
fixture back to the
mid-position.
WARNING: Turn power off at circuit
breaker.

3
598-1167-03
Wiring to Motion Light &
Standard Fixture
BLACK
WHITE
BLACK
(Standard)
❒When wiring to additional standard
fixture only: Strip the motion sensor’s
red wire and connect to the standard
light’s black wire. Connect all white wires
together. Total fixture ratings must not
exceed 360 Watts (3.0 A.).
Note: All wiring between fixtures should
be run in accordance with the National
ElectricalCodethroughconduitoranother
acceptable means. Contact a qualified
electrician if there is any question as
to the suitability of the system.
❒This fixture is provided with a sensor rated
for 360 Watts. Since the fixture is only rated
100 Watts (180 Watts candelabra), 260
Watts (180 Watts candelabra) of additional
load may be controlled by this sensor.
❒When determining what a fixture is rated
for, do not simply look at the rating on the
lamp in the fixture. Look at the marking
which specifies the maximum lamp watt-
age for which the fixture is suitable.
❒Once you have selected the fixtures to be
connectedanddeterminedtheirmaximum
ratings,addthese ratingsup.Forinstance,
if you have 3 fixtures rated 100 Watts, 150
Watts,and75Wattsrespectively, youhave
a total load of 325 Watts.
RED
WHITE
BLACK
BLACK
Master Slave
Wiring to Control One Motion Sensing
Lantern (Slave) from Another (Master)
It is also possible to wire two motion sensing coach lights so that either unit will turn on
both lights at the same time (dual master system). It is recommended that only people with
plenty of electrical experience attempt this configuration. Please call our customer service
number (1-800-858-8501 - English Speaking Only) before attempting this wiring. If the dual
master wiring is not done correctly, it can destroy both motion sensing fixtures and
void your warranty.
RED
OPTIONAL WIRING

4598-1167-03
COMPLETE THE INSTALLATION
❒Stuff the wires into the junction box.Make
sure none of the wires get pinched.
Slide the fixture onto the
mounting screws and
tighten nuts.
❒ Install one 100W max.light bulb, or three
60 W bulbs in candelabra style.
❒ Install the fixture top. Secure with
decorative screws.
❒Aftercompletingthetestsonpage5,caulk
fixture mounting surface with silicone
weather sealant.
Junction
Box
Model 4193 Glass Installation
❒ Model 4193 only: install the six pieces
of glass by sliding them down as shown.
The glass panels should rest upon the
corner guides on each side, and against
the rubber bumpers at the bottom.
Note: As with any glass, handle with care.
Corner
Guides
Rubber Bumpers

5
598-1167-03
TESTING
❒Turn on the circuit breaker and light
switch.
The detector is less sensitive to motion
directly towards it and more sensitive to
across motion.
Sensor
Motion
Least Sensitive Most Sensitive
❒Walk through the coverage area noting
where you are when the lights turn on.
❒If you need to change the sensitivity,
temporarily remove the fixture and make
the adjustment.Too much sensitivity may
increase false triggering.
❒Set the amount ofTIME you want the light
to stay on after motion is detected. (1, 5,
or 10 minutes).
❒Setthe amount of time after dusk youwant
the lights on accent level.
SPECIFICATIONS
Range . . . . . . . . . . Up to 30 ft. (9.1 m)
[varieswithsurrounding
temperature].
Sensing Angle . . . . Up to 180°
Electrical Load. . . . See rating on fixture for
maximum wattage.
Sensor Capacity . . Up to 360 Watt (3.0 A.)
Maximum
Power
Requirements . . . . 120 VAC, 60 Hz
Operating Modes. . TEST, AUTO, and
MANUAL MODE
Time Delay . . . . . . 1, 5, 10 minutes
DualBrite®timer . . 3, 6 hrs, Dusk-to-Dawn
DESA Specialty Products reservestherightto
discontinue products and to change specifica-
tions at any time without incurring any obliga-
tion to incorporate new features in products
previously sold.
Note: Sensorhasa11/2minute warm up pe-
riod before it will detect motion.When
first turned on, wait 1 1/2minutes.
TEST 1 5 10 MIN
ON-TIME
OFF 3 6 DUSK TO
HOUR DAWN
Avoid aiming the control at:
• Objects that change temperature rapidly,
such as heating vents and air condition-
ers. These heat sources could cause false
triggering.
• Areas where pets or traffic may trigger
the control.
• Nearby large, light-colored objects
reflecting light may trigger the shut-off
feature. Do not point other lights at the
sensor.
30 ft.
(9.1 m)
Maximum Range Maximum
Coverage Angle
180°
Motion
❒Switch the on-time to TEST position and
DualBrite®switch to the OFF position.
6 ft.
(1.8 m)

6598-1167-03
SYMPTOM
Light comes
on for no
apparent
reason.
Light stays
on continu-
ously.
Light flashes
on and off.
POSSIBLE CAUSE
1. Light Control may be sens-
ing small animals or au-
tomobile traffic (Reduce
sensitivity).
1. Thesensor ispointedtoward
aheatsourcelike anairvent,
dryervent,orbrightly-painted
heat-reflective surface.
(Reduce sensitivity.)
1. Light Control is in the Test
mode and warming up.
(Flashing is normal under
these conditions).
POSSIBLE CAUSE
1. Light switch is turned off.
2. Bulb is loose or burned out.
3. Fuse is blown or circuit
breaker is turned off.
4. Daylight turn-off is in effect
(recheck after dark).
5. Incorrectcircuitwiring,ifthis
is a new installation.
1. Light Control may be in-
stalled in a relatively dark
location.
2. Light Control is inTest. (Set
control switch to an ON-
TIME position.)
SYMPTOM
Light will not
come on.
Light comes
on in daylight.
TROUBLESHOOTING GUIDE
THREE YEAR LIMITED WARRANTY
This is a “Limited Warranty” which gives you specific legal rights.You may also have other rights which vary
from state to state or province to province.
For a period of three years from the date of purchase, any malfunction caused by factory defective parts or
workmanship will be corrected at no charge to you.
NotCovered-Repairservice,adjustmentandcalibrationduetomisuse,abuseornegligence,lightbulbs,batteries,
and other expendable items are not covered by this warranty. Unauthorized service or modification of the product
or of any furnished component will void this warranty in its entirety.This warranty does not include reimbursement
for inconvenience, installation, setup time, loss of use, unauthorized service, or return shipping charges.
This warranty covers only DESA Specialty Products assembled products and is not extended to other equip-
ment and components that a customer uses in conjunction with our products.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, IN-
CLUDING ANY WARRANTY, REPRESENTATION OR CONDITION OF MERCHANT ABILITY OR THAT THE
PRODUCTS ARE FIT FOR ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OF ALL
SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUSTOMER AND THERE SHALL
BE NO LIABILITY ON THE PART OF DESA SPECIALTY Products FOR ANY SPECIAL, INDIRECT, INCI-
DENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITEDTO ANY LOSS OF BUSINESS
OR PROFITS, WHETHER OR NOT FORESEEABLE. Some states or provinces do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
Proof of purchase is required for warranty claims.
TECHNICAL SERVICE
Please call 1-800-858-8501 (English speaking only) for assistance before
returning product to store.
If you experience a problem, follow this guide. You may also want to visit our Web site at:
www.desatech.com. If the problem persists, call* for assistance at 1-800-858-8501 (English
speaking only),7:30 AM to 4:30 PM CST (M-F).You may also write* to:
DESA Specialty Products
P.O. Box 90004, Bowling Green, KY 42102-9004
ATTN: Technical Service Specialty Products
* If contacting Technical Service, please have the following information available: Model Number, Date of Purchase,
and Place of Purchase.
No Service Parts Available for this Product

7
598-1167-03
Farol de fundición
con detector de
movimiento
LUZ DE ADORNO
Para una iluminación ornamental de baja
intensidad,pongaelinterruptordeDualBrite®
en la posición de 3, 6, ó del Dusk-to-Dawn
(atardecer-al-amanecer).Cuandosedetecte
movimiento, las luces se pondrán en alta
intensidad.
FUNCIONAMIENTO
*Se pone en Automático al amanecer.
Serie PF-4190
Características
• La luz se prende cuando se detecta mov-
imiento.
• Apaga la luz automáticamente.
• Iluminación ornamental de baja intensidad.
• La fotocélula mantiene la luz apagada
durante las horas del día.
Requisitos
• El Control de Luz requiere 120 VCA.
• Para usar el Sobrecontrol Manual, conecte
el control con un interruptor.
• Algunos códigos requieren instalación
por un electricista calificado.
Este paquete contiene:
• Farol
• Soporte universal de fácil uso (X-Bar)
• Ferretería de montaje
• Conectores de alambre
© 2006 DESA Specialty Products™ 598-1167-03 S
PRUEBA
ON-TIME
Pongaelinterruptordetiempo(ON-
TIME),al fondo deldetector, en la
posición de prueba (TEST). TEST 1 5 10
1 segundo
APAGADO
luego...
El modo manual funciona sólo
por la noche porque la luz del
día pone al detector en modo
AUTOMATICO.
Apague el interruptor por un
segundo y vuélvalo a prender.
El modo manual funciona sólo
cuandoelinterruptordetiempo
(ON-TIME) está en la posición
de 1, 5 ó 10 minutos.
ON-TIME
TEST 1 5 10
Pongaelinterruptordetiempo
(ON-TIME) en la posición de
1, 5 ó 10 minutos.
MODO MANUAL
...préndalo.
Mueva el interruptor de
tiempo (ON-TIME) a 1, 5 ó
10 minutos
Apague el interruptor
por un segundo y
préndalo de nuevo*
PRUEBA
AUTOM.
MODO
MANUAL
* Si se confunde mientras cambia de fases,
apaguelaelectricidadporunminutoypréndala
de nuevo. Después del tiempo de calibración
el control estará en fase AUTO(MATICA).
Resumen de las modalidades del
interruptor
AUTOMATICO
Nota: Cuando lo prenda por primera vez es-
pere 1 1/2minutos para que el circuito
se claibre.
Modalidad: A tiempo: Trabaja: Día Noche
Prueba 5 seg. x x
Autom. 1, 5 ó 10 min. x
Manual Hasta el
amanecer*
x
Adorno 3, 6 hrs, hasta
el amanecer
x

8598-1167-03
CABLEADOINSTALACION
Para un mejor funcionamiento, instale el
aparato a casi 1.8 m del suelo.
5. Monte el soporte
X-Bar a la caja de
empalme.
4. Fije de nuevo el
alcance de sensibilidad a
la posición del medio.
2. Quite la banda
"X" de montaje.
3. Ajuste los tornil-
los tan sólo con los
dedos. MAX
MIN
SENSITIVITY
la caja
de em-
palme
Debido al tamaño y peso del aparato, será
prudente quesuasistente sotengael aparato
mientras se conectan los cables.
Negro a negro Blanco a blanco
Método recomendado de conexión a tierra
Use un "cable flexible" verde de a tierra (no pro-
visto) y tuerza un extremo con el cable desnudo
del aparato y con el cable de a tierra de la caja.
Asegúrelos con un conector de cables. Asegure
el otro extremo del "cable flexible" con el tornillo
de a tierra de la placa de montaje.
❒ Tuerza los cables de la caja de empalme
conloscablesdelaparato, comose mues-
tra abajo. Asegúrelos con conectores de
cables. Si tiene una caja de empalme de
metal, no necesita el "cable flexible". Si
no está seguro del método de conexión
a tierra, consulte con el código local de
construcción.
CUIDADO: NO conecte el cable ROJO
excepto que desee controlar otras luces
desde el detector de movimiento.
Luz de dos movimientos
BLANCO
NEGRO NEGRO
NEGRO
BLANCO
Luz de un movimiento
1. Quite las
dos tuercas.
ADVERTENCIA:Desconectelaenergía
en el disyuntor.

9
598-1167-03
Conexión a la luz de movimento y al aparato
estándar
BLANCO
NEGRO NEGRO
(Estándar)
❒Encasodeconectaralaparatoestándar
solamente:Peleelalambrerojodeldetec-
tor de movimiento y conéctelo al alambre
negro de la luz estándar. Conecte todos
los alambres blancos. La capacidad total
no debe exceder los 360 Vatios (3.0 A).
Nota: Todo el cableado entre los aparatos
debe estar hecho de acuerdo al Código
Eléctrico Nacional por medio de un con-
ducto o cualquier otro medio aceptable.
Comuníqueseconunelectricistacalifi-
cado si tiene cualquier pregunta refer-
ente a la adaptabilidad del sistema.
❒Este aparato viene con un detector con una
potenciade360Vatios.Puestoqueelaparato
tiene sólo una potencia de 100 Vatios (180
Vatios candelabro), la carga adicional de
260 Vatios (180 Vatios candelabro) puede
ser controlada por el detector.
❒Cuando desee determinar la clasificación
de un aparato no vea tan sólo la potencia
de la lámpara. Mire la indicación que es-
pecifique el voltaje máximo de la lámpara
que el aparato puede aceptar.
❒Una vez que ha escogido los aparatos
que se conectarán y ha determinado sus
máximaspotencias,súmelas.Porejemplo,
si tiene 3 aparatos de 100 , 150 y 75Vatios
respectivamente, usted tendrá un total de
325 Vatios.
ROJO
Maestra Esclava
NEGRO ROJO
NEGRO
BLANCO
Conexión para controlar una luz de mov-
imiento (esclava) desde otra (maestra)
También es posible conectar dos luces de movimiento de forma que cualquiera de las dos
unidades pueda encender simultáneamente ambas luces (sistema de doble maestro). Se
recomienda que sólo personas con amplios conocimientos de electricidad conecten este
tipo de configuración. Por favor comuníquese con nuestro departamento de asistencia al
cliente (1-800-858-8501 - sólo para hablar en inglés) antes hacer este tipo de conexión. La
conexión inadecuada del cableado de doble maestro podría dañar ambas luces de
movimiento y anular la garantía. Lo sentimos, pero no podemos contestar preguntas en
español por teléfono.
CONEXION ALTERNA

10 598-1167-03
COMPLETE LA INSTALACION
❒Meta los cables en la caja de empalme.
Asegúrese que los cables que no estén
pinchados.
❒ Instale una bombilla de 100Vatios Máx.,
ó 3de 60 Vatios en estilo candelabro.
❒ Instale la parte de arriba. Asegúrela con
tornillos decorativos.
❒Después de completar la prueba de la
página 11, calafatee el aparato y la
superficie de montaje con un sellador
de silicona contra la intemperie.
Deslice al apartato sobre
los tornillos de montaje y
ajuste las tuercas. la caja de
empalme
Instalación del vidrio del Modelo
4193
❒ Modelo 4193 solamente: Instale las seis
piezasdevidriodeslizándolashaciaabajotal
comoseindica.Lospanelesdevidriodeben
descansar en las gu’as de las equinas en
cadalado,ypordetrásdelosamortiguadores
de goma de la parte inferior.
Nota: A igual que con cualquier clase de
vidrio, trátelo con cuidado.
Gu’as de las
esquinas
Amortiguadores de goma