POSIFLEX PP-7600 User manual

1
Package Contents
PP-7600 POS Printer………………(x1)
80mm-wide Thermal Paper………..(x1)
(For operational testing)
58mm Paper Spacer Plate………….(x1)
24V/60W Power Adapter………….(x1)
Power Cord………………………...(x1)
USB Cable…………………………(x1)
RS232 Cable (Optional)…………...(x1)
Soft Wiping Cloth…………………(x1)
User Manual……………………….(x1)
Product Features
3" thermal printer with auto cutter
Printing speed up to 200 mm/sec
High-resolution printing up to 576 dots/line (W 8 dots/mm x H 8
dots/mm)
80 mm or 58 mm paper width support
Drop-and-load action for easy paper roll replacement
Control over 2 cash drawers through 1 D.K port
Optional kitchen bell function
Interface: USB (True USB & Virtual COM selectable) + serial, optional
LAN or WLAN (WiFi) interface module
High compatibility with Android, Linux, and Windows operating system,
allowing users to simply print a receipt via computer, tablet, or
smartphone
Easy wireless printing not only bringing along the mobility but also
increasing the productivity
Printing anytime and anywhere
Near end sensor
Optional LD-2000 light bar modular
PP-7600
POS Printer
User Manual
19302900020 Ver. A0
http://www.posiflex.com

2
Views of the PP-7600
Front View
Part Names
Description
Power Button
This button turns the printer on or off.
Power LED Indicator
This indicator turns on when the printer is on.
Error LED Indicator
This indicator works when the printer has
something wrong. For more details, refer to the
Status LED Indicators section given below.
Paper-out LED Indicator
This indicator turns on when the paper-out issue
occurs.
Feed Button
Press this button once to feed the paper roll for one
line. Hold down this button to continue feeding the
roll paper
Paper Cover
Open this cover when installing or replacing the
paper roll.
Cover Open Lever
Push this lever to open the paper roll cover.
Paper Exit
An opening where the paper is outputted
Paper-out LED Indicator
Wedge Groove
Power Button
Power LED Indicator
Error LED Indicator
Feed Button
Cover Open Lever
Paper Roll Exit
Paper Cover
Paper Near End Sensor
Paper Roller

3
Part Names
Description
Wedge Groove
A settled routine that makes the paper spacer plate
hard to escape
Paper Near End Sensor
(Provided for adjusting the detection position to suit
the diameter of the paper core used, and for
adjusting the detection position of remaining
amount of paper)
Rear View
Part Names
Description
Power Jack
for LD-2000
Connects the DC cable of LD-2000
Printer Power
Connector
Connects the DC cable for the power adapter of PP-
7600
Printer Power Connector
Cable Cover
Power Jack for LD-2000

4
Bottom View
Part Names
Description
Networking Module
Slot
A slot for optional LAN or Wi-Fi networking
module
I/O Ports
USB connector (Type-B)
Serial port connector (RS232)
Cash drawer connector (RJ10)
Fixing Screw Hole
for LD-2000
Formed for fixing the optional LD-2000 light bar
Wedge Groove
for LD-2000
Formed for fixing the optional LD-2000 light bar
I/O Ports of the PP-7600
Serial (RS232) Port
D.K (RJ10) Port
USB Port (Type-B)
Networking Module Slot
Fixing Screw Hole
for LD-2000
Wedge Groove
for LD-2000
Rubber Foot
I/O Ports

5
Loading a Paper Roll
Before loading a paper roll, make sure you use a specified paper type. Follow
the steps below to load a paper roll.
1. Press down the cover open lever to
release the paper cover.
2. The paper cover ejects. Then, open the
paper cover manually.
3. Drop the 80mm-wide thermal paper
inside the paper compartment of the
printer, as shown in the right figure.
4. Drag the paper roll to the portion where
the paper roller is installed.
Paper Roller

6
If you want to use a paper roll of 58mm
width, install the spacer plate in the
compartment of the printer, as shown in
the right figure, and then load the paper
roll of 58mm width into the partition at
the right side of the plate.
Next, set the paper width by using the PP-7600 software switch utility.
The software switch utility can be downloaded from the Posiflex’ global
website:
http://www.posiflex.com/en-global/Download/download. To get more
detailed information on the paper width jumper setting, contact directly
the Posiflex’ technical service team.
5. To avoid the paper cover not being
locked completely, push the central
portion of the paper cover to close.
Push

7
Connecting Power Adapter and I/O Cables
Follow the steps listed below to open the rear cover and connect cables.
1. Hold the concave portion of the cable cover
with thumb, as shown in the circled portion
of the figure.
2. Pull the cover in the direction indicated by
the arrow in the right figure.
3. Remove the cable cover.
4. Connect power adapter to the printer power
connector of the PP-7600.
Remove

8
5. Connect I/O cable(s) to the I/O port(s) of the
PP-7600.
6. Make the cable cover wedge to the printer.
Determine that the cable cover is well
wedged to the printer.
7. Cover the I/O ports of the printer.
8. Determine that the cable cover is completely
closed.
Connect
to I/O ports
Firmly Closed

9
Installing the LD-2000 Light Bar (Optional)
Follow the steps below to install the LD-2000 light bar on the PP-7600 printer.
Power off the printer when installing the LD-2000 light bar.
1. Determine that the micro USB connector of
the cable for LD-2000 to PP-7600 is
securely connected to the micro USB port on
the LD-2000 control board.
2. Plug the L-formed header of the LD-2000 power cable into the LD-2000
power jack of the PP-7600 printer.
3. Make the four joints formed on the LD-2000 wedge to the four wedge
grooves formed on the PP-7600.
4. Determine that the LD-2000 securely
connects to the PP-7600.

10
5. Fix the LD-2000 to the bottom side of PP-
7600 with a screw.
6. The installation of LD-2000 light bar is
completed.
After installing the LD-2000 light bar, you can set up the LD-2000 by using
the Posiflex LD2000 Tool. For more detailed information, refer to the Posiflex
LD2000 Tool. To download the LD2000 Tool and its manual, go to the
Posiflex’ global website: http://www.posiflex.com/en-
global/Download/download.
LD-2000
Light Bar