Positron G1002-M User manual

G.hn to Gigabit Ethernet Bridge
Quick Installation Guide
G1002-M / G1002-M+ / G2002-M+

G1002-C Quick Installation Guide
Positron Access Solutions 2 Document 180-0220-001 R01
Publication Information
©2022 Positron Access Solutions
G1002-M / G1002-M+ / G2002-M+ Quick Installation Guide
Publication date: February 2022
Printed in Canada
Published By
Positron Access Solutions
5101 Buchan Street, Suite 220
Montreal, Quebec, Canada
H4P 2R9
Telephone US and Canada: 1-888-577-5254
International: [phone]
Product names, other than Positron's, mentioned herein may be trademarks and/or registered trademarks
their respective companies.
Disclaimer Notice
Although Positron Access Solutions has made every effort to ensure the accuracy of the information
contained herein, this document is subject to change.

G1002-C Quick Installation Guide
Positron Access Solutions 3 Document 180-0220-001 R01
CONTENTS
.........................................................................................................................................4
About the G1002-M / G1002-M+ / G2002-M+................................................................................4
Introduction........................................................................................................................4
G1002-M (Copper) Endpoint.............................................................................................6
G1002-M LED Definition..............................................................................................6
G1002-M+ (Copper) Endpoint...........................................................................................7
G1002-M+ LED Definition............................................................................................8
G2002-M+ (Copper) Endpoint...........................................................................................8
G2002-M+ LED Definition............................................................................................9
G1002-M / G1002-M+ / G2002-M+ Gigabit Ethernet Ports ..............................................9
Physical Mounting of the G1002-M / G1002-M+ / G2002-M+ ........................................10
.......................................................................................................................................11
Technical and Regulatory Specifications..................................................................................11
G1002-M Technical Specifications..................................................................................11
G1002-M+ Technical Specifications ...............................................................................12
Regulatory Compliance...................................................................................................13
G2002-M+ Technical Specifications ...............................................................................13
Regulatory Compliance...................................................................................................14
.......................................................................................................................................17
Warranty and Customer Service ................................................................................................17

G1002-C Quick Installation Guide
Positron Access Solutions 4 Document 180-0220-001 R01
______________________________________
About the G1002-M / G1002-M+ / G2002-M+
Introduction
The G1002-M, G1002-M+ and G2002-M+ G.hn to Ethernet Bridge devices
complete the G.hn link (1 or 2 copper pairs) with the G.hn Access Multiplexer
(GAM) and converts the G.hn interface to a standard Gigabit Ethernet (RJ-45)
interface. They are designed for indoor installation, usually inside the subscriber
premises and connect to a Residential Gateway (RG) or comparable devices.
While each of these devices perform a similar function, here is a summary of the
unique features of each model:
•G1002-M: this G.hn Endpoint is locally powered and offers two (2) Gigabit
Ethernet ports (RJ-45). The 1st Ethernet Port can be configured as a VLAN
Trunk port when there is a need to support a large number of VLANs. The
2nd Ethernet Port can be configured as a VLAN Access port when there is
a need to support no more than twelve (12) VLANs.
•G1002-M+: this G.hn Endpoint is locally powered and offers two (2) Gigabit
Ethernet ports (RJ-45). The 1st Ethernet Port can be used to power another
device over Ethernet, it can operate in POE mode (15.4W as per IEEE
802.3af) or in POE+ mode (30W as per IEEE 802.3at). This first port can
be configured as a VLAN Trunk port when there is a need to support a large
number of VLANs. The 2nd Ethernet Port does not support POE/POE+, it
can be configured as a VLAN Access port when there is a need to support
no more than twelve (12) VLANs.
•G2002-M+: this G.hn Endpoint is either locally powered or line powered
from the GAM (requires two (2) copper pairs (MIMO mode). It offers two (2)
Gigabit Ethernet ports (RJ-45). The 1st Ethernet Port can be used to power
another device over Ethernet, it can operate in POE mode (15.4W as per
IEEE 802.3af) when locally powered and when line powered from a GAM.
Support for POE+ mode (30W as per IEEE 802.3at) requires a local power
source. This first port can be configured as a VLAN Trunk port when there

G1002-C Quick Installation Guide
Positron Access Solutions 5 Document 180-0220-001 R01
is a need to support a large number of VLANs. The 2nd Ethernet Port does
not support POE/POE+, it can be configured as a VLAN Access port when
there is a need to support no more than twelve (12) VLANs.
About G.hn
The ITU-T G.9960 G.hn Wave-2 standard leverages the existing telephone wiring
(UTP, CAT-3 or CAT-5/5e) or RG-6/RG-59 coax cabling to deliver a Gigabit
Internet service to each subscriber without the cost, complexity and delays
associated with in-building fiber installation. G.hn is an Access technology for
Operators looking to simplify their access network and backend infrastructure with
an Ethernet-like technology that is highly scalable without some of the inherent
complexity of DSL-related technologies. With G.hn, Operators deliver advanced
services such as Gigabit High Speed Residential Internet and 4K IPTV without the
high capital and operational expenses associated with a fiber retrofit. Each G.hn
subscriber port supports up to 1.7 Gbps of dynamically allocated bandwidth for
near symmetrical Gigabit services over the existing telephone wire or coaxial
cable.
Note: Read Chapter entitled “Safety and Warnings”before proceeding.

G1002-C Quick Installation Guide
Positron Access Solutions 6 Document 180-0220-001 R01
G1002-M (Copper) Endpoint
The G1002-M (coper) G.hn Bridge to Gigabit Ethernet comes with two (2) Gigabit
Ethernet port to connect the Residential Gateway (RG).
Figure 1: G1002-M Gigabit Ethernet Port and Status LEDs
Figure 2: G1002-M port definition
G1002-M LED Definition
LED position
Description
G.hn (green)
ON indicates G.hn link up
OFF indicates G.hn link down
BLINKING indicates G.hn link speed less than 40 Mbps
PWR (green)
Indicates power on or off
STA (yellow)
Green indicates units is working
Yellow indicates unit is booting or being reset
Table 1: G1002-M LED Definition
G.hn Port (RJ-45)
12Vdc Jack
2 x Gigabit Ethernet (RJ-45)
G1002-M Status LEDs/

G1002-C Quick Installation Guide
Positron Access Solutions 7 Document 180-0220-001 R01
Figure 3: G1002-M LED definition
G1002-M+ (Copper) Endpoint
The G1002-M+ (copper) G.hn Bridge to Gigabit Ethernet comes with two (2)
Gigabit Ethernet port to connect the Residential Gateway (RG). The Gigabit
Ethernet Port labelled as GE1 supports POE / POE+ to power an external device.
Figure 4: G1002-M+ Gigabit Ethernet Port and Status LEDs
Figure 5: G1002-M+ port definition
G1002-M Status LED
G.hn Status LED
Power LED
G.hn Port (RJ-45)
48Vdc Jack
2 x Gigabit Ethernet (RJ-45)
G1002-M+ Status
LEDs/
GE1 POE status LED

G1002-C Quick Installation Guide
Positron Access Solutions 8 Document 180-0220-001 R01
G1002-M+ LED Definition
LED position
Description
G.hn (green)
ON indicates G.hn link up
OFF indicates G.hn link down
BLINKING indicates G.hn link speed less than 40 Mbps
PWR (green)
Indicates power on or off
STA (yellow)
Green indicates units is working
Yellow indicates unit is booting or being reset
POE
Green indicates port GE1 is providing POE to an
attached device
Table 2: G1002-M+ LED Definition
Figure 6: G1002-M+ LED definition
G2002-M+ (Copper) Endpoint
The G2002-M+ (coper) G.hn Bridge to Gigabit Ethernet comes with two (2) Gigabit
Ethernet port to connect the Residential Gateway (RG). The Gigabit Ethernet Port
labelled as GE1 supports POE / POE+ to power an external device.
Figure 7: G2002-M+ Gigabit Ethernet Port and Status LEDs
G1002.M+ Status LED
G.hn Status LED
Power LED
G.hn Port (RJ-45)
2 x Gigabit Ethernet (RJ-45)
G2002-M+ Status LED
GE1 POE status LED
GE1 POE status LED

G1002-C Quick Installation Guide
Positron Access Solutions 9 Document 180-0220-001 R01
Figure 8: G2002-M+ port definition
G2002-M+ LED Definition
The G2002-M+ status LEDs are defined in the following table:
LED position
Description
G.hn (green)
ON indicates G.hn link up
OFF indicates G.hn link down
BLINKING indicates G.hn link speed less than 40 Mbps
PWR (green)
Indicates power on or off
STA (yellow)
Green indicates units is working
Yellow indicates unit is booting or being reset
POE
Green indicates port GE1 is providing POE to an
attached device
Table 3: G2002-M+ LED Definition
Figure 9: G2002-M+ LED definition
G1002-M / G1002-M+ / G2002-M+ Gigabit Ethernet Ports
The G1002-M, G1002-M+ and G2002-M+ incorporate two (2) RJ-45 Gigabit
Ethernet ports. Please note that port GE1 can be configured in VLAN Trunk mode
(via the GAM) if required for your application.
The GE1 port of the G1002-M+ and G2002-M+ supports Power Over Ethernet to
power an external device. When locally powered, the G1002-M+ and G2002-M+
48Vdc Jack
Status LED
G.hn Status LED
Power LED
GE1 POE status LED

G1002-C Quick Installation Guide
Positron Access Solutions 10 Document 180-0220-001 R01
can provide up to 30W of power as per the IEEE 802.3at standard. When the
G2002-M+ is line powered from the GAM, the GE1 port is limited to a maximum
power of 15.4W as per the IEEE 802.3af standard.
Physical Mounting of the G1002-M / G1002-M+ / G2002-M+
The G1002-M / G1002-M+ and G2002-M+ share the same base enclosure and
have the same mounting options. You can optionally install (mount) the enclosure
on a wall or flat surface as follows:
1. Select a proper mounting location where you can securely install mounting
screws (not supplied).
2. Use the enclosure as a guide to determine where you need to install the two
(2) mounting screws.
3. Install the lower screw into the wall but do no tighten completely. Use a wall
plug if inserting the screws into a dry wall. Leave enough room to insert the
enclosure (see step 4).
4. Insert the enclosure slot (as per the figure 5 below) and slightly tighten the lower
screw to hold the device in place while you install the top screw.
5. Tighten both screws to secure in place but do not apply too much torque to
avoid damaging the screws or the wall mounting.
Figure 10:
Use two (2) screws #10 (5mm) to install the
enclosure on a flat surface. If mounting on a dry
wall, use adequate wall plugs (not supplied)