pottery barn kids OWEN TWIN OVER TIWN BUNK BED User manual

pottery barn kids
OWEN TWIN OVER TIWN BUNK BED
www.potterybarnkids.com
Date: 2015-Oct.-13
Rev: Page 1 of 10

! WARNING:.Failure to follow these warnings and assembly
instructions could result in serious injuryor death. To help prevent serious
or fatal injuries fromentrapment or falls:
•Read all instructionsbefore assembling bunk bed.
•Before each usage or assembly, inspect bunk bed for damaged hardware, loose joints,
missing partsorsharp edges. DO NOT use bunk bed if any partsare missing or broken.
•DO NOT use substituteparts. Contact potterybarn kids for replacement parts and
instructional literature ifneeded.
•Followthe information on the warnings appearing on the upper bunkend structureand
on the carton. DO NOT REMOVE WARNING LABEL FROM BED.
•Always use the recommended size mattress or mattresssupport, or both,tohelp prevent
the likelihood of entrapment or falls.
•Ensure thickness of mattress on upper bunk does not exceed7inches and the surface
of mattress mustbe at least5 inches (127 mm) below the upper edgeof guardrails.
•Only use the 9" thickness mattress on the lower bunk.
•
Ensureboth upper and lower bunk are assembled to the highestposition when using the
productas a bunk bed.
•Use only mattress which is74"-75" long and 37.5"-38.5" wide on upper and lower bunk.
•Do not allowchildren under 6 years ofage to usetheupper bunk.
•Periodically checkand ensure that the guardrail, ladder, and other components are in their
proper position, free from damage,and that allconnectorsaretight.
•Do not allowhorseplayon or under the bedand prohibit jumping on the bed.
•Prohibit more than one person on the upper bunk.
•Always use the ladder for entering and leaving the upper bunk.
•Use of anightlight may provide added safetyprecaution for a child using the upper bunk.
•Always use guardrailson both long sides ofthe upper bunk. If the bunkbed will beplaced
next to the wall, the guardrail that runs the full length of the bed shouldbe placed against
the wall to prevent entrapment between the bed and wall.
•The use of water or sleep flotation mattresses isprohibited.
•If refinishing, use a non-toxic finish specified for children's products.
STRANGULATION HAZARD -Never attach or hang items to any partof the bunk bed
thatare not designed for use with the bed; for example, butnot limited to,hooks,belts
and jump ropes.
•This bunkbed meets the requirementsof ASTMF1427-13
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
04-0000217
Date: 2015-Oct.-13
Rev: Page 2 of 10

Important Safety Instructions:
•Please read all instructions carefully before assembling.
•For your safety, assembly by three or more adults is strongly recommended.
•Keep instructions for future use.
•Use only vendor supplied hardware to assemble. Using unauthorized hardwarecould jeopardize the structural integrity
of the item.
•Do not remove warning labels from the bunk bed. Labels are permanent and not designedto be removed.
Pre-assembly:
•Remove all parts and hardware from the box and lay out on a clear carpeted or scratch-free worksurface, as this will
avoid damaging parts during assembly. The shipping box provides an ideal work surface.
•Do not dispose of any packaging or contents of the shipping carton until assembly is completed to avoid accidentally
discarding small parts or hardware.
•Use the parts and hardware lists below to identify andseparate each of the pieces included.
•The illustrations provided allow for easier assembly when used in conjunction with the assembly instructions.
•The use ofpower tools to aid in assembly is not recommended. Power tools can damage hardware and split wood.
•Note: Do not fully tighten all bolts until all parts are in place. Failure to follow these instructions may cause the bolts to
misalign during assembly.
Parts Included:
(A) Headboard (1x)
(B) Footboard (1x)
(C) Side rail (2x)
(D) Long guard rail (1x)
(E) Short guard rail (1x)
(F) Slat roll (2x)
(G) Ladder (1x)
Hardware Included:
(H) Barrelnut M8
16x
(I) Long Allen bolt
M8x90 mm – 8x
(J) Short Allen bolt
M8x70 mm – 3x
(K) Allen key with ball
tip
1x
(L) Flat head wood screw
4x30 mm – 56x
(M) Flathead wood
screw
4x15 mm – 4x
Tools Required (not included):
Philips Head Screwdriver
D
C
B
F
A
G
E
Date: 2015-Oct.-13
Rev: Page 3 of 10

AssemblyInstruction Steps:
1. Attach (C) to (A) asshown below.
Note: Do not fully tighten the bolts to make the next steps easier.
H 2x
I 2x
A
C
2x
2x
H
I
K
Date: 2015-Oct.-13
Rev: Page 4 of 10

2. Attach (D) to (A) as shown below.
Note: Do not fully tighten the bolts to make the next steps easier.
H 2x
I 2x
J 1x
D
1x
2x
2x
A
H
J
I
K
K
Date: 2015-Oct.-13
Rev: Page 5 of 10

3. Attach (B) to (C) and (D) as shown below.
Note: Do not fully tighten the bolts to make the next steps easier.
4.
H 4x
I 4x
J 1x
D
B
C
1x
K
I
H
4x
J
Date: 2015-Oct.-13
Rev: Page 6 of 10

5. Carefully attach (C &E) to (A&B) by spreading (A& B) as shown below.
4x
E
C
A
B
Spreading
Date: 2015-Oct.-13
Rev: Page 7 of 10

6. Secure (C) and (E) as shown below.
7. Check the alignments and fully tighten all bolts at this time. Do not over tighten.
H 8x
I 8x
J 1x
H
8x
1x
K
J
I
K
Date: 2015-Oct.-13
Rev: Page 8 of 10

8. Attach (G) onto (E) and (C). Secure the ladder with (M) using a Phillips head screwdriver
(Not included). Make sure to use pre-drilled holes as guidance.
M 4x
4x
G
E
C
M
Date: 2015-Oct.-13
Rev: Page 9 of 10

9. Lay the slat roll (F) onto the support rails on the inner side of (C), (D) and (E). Secure each
slat by wood screw (L) at two ends using a Phillips head screwdriver (Not included).
10.Assembly is completed
Care Instructions:
•Dust oftenusing a clean, soft, dry and lint-free cloth.
•Blot spills immediately and wipe with a clean, damp, cloth.
•We do not recommend theuse of chemical cleansers,abrasives or furniturepolish on our lacquered finish.
•Hardware may loosenover time. Periodically checkto make sure allconnectionsare tight. Re-tighten if
necessary.
Thank you for your purchase
Stores | catalog | www.potterybarnki ds .com
USA 1.800.290.8181
L 56x
56x
F
L
Date: 2015-Oct.-13
Rev: Page 10of 10