pottery barn kids BLYTHE CARRIAGE BED TWIN User manual

Date: 2016-Jun.-03
Rev: Page 1 of 15
pottery barn kids
BLYTHE CARRIAGE BED
TWIN / FULL
www.potterybarnk i ds.com

Date: 2016-Jun.-03
Rev: Page 2 of 15
Important Safety Instructions:
•Please read all instructions carefully before assembling.
•For your safety, assembly by two or more adults is strongly recommended.
•Keep instructions for future use.
•Use only vendor supplied hardware to assemble. Using unauthorized hardware could
jeopardize the structural integrity of the item.
Pre-assembly:
•Remove all parts and hardware from the box and lay out on a clear carpeted or scratch-free
work surface, as this will avoid damaging parts during assembly. The shipping box provides
an ideal work surface.
•Do not dispose of any packaging or contents of the shipping carton until assembly is
completed to avoid accidentally discarding small parts or hardware.
•Use the parts and hardware lists below to identify and separate each of the pieces included.
•The illustrations provided allow for easier assembly when used in conjunction with the
assembly instructions.
•The use of power tools to aid in assembly is not recommended. Power tools can damage
hardware and split wood.
Parts Included:
(A) Headboard - 1pc
(B) Footboard - 1pc
(C) Side rail - 2pcs
(D) Top rail - 2pcs
(E1) Left side panel - 2pcs
(E2) Right side panel - 2pcs
(F) Slat roll - 1set
(G) Bun foot - 4pcs
(H) Finial - 4pcs
(I) Side curtain - 4pcs
(J) Front Curtain -2pcs
(K) Curtain Tie -6 pcs
Noted: (I)(J)(K) sold separately.

Date: 2016-Jun.-03
Rev: Page 3 of 15
HARDWARE INCLUDED:
(L)Allen Key with ball
tip – 1x
(M) LongAllen bolt
5/16”x63mm – 8x
(N) Medium Allen bolt
1/4”x63mm – 12x
(O) Short Allen bolt
1/4”x15mm – 24x
(P) Spring Washer
5/16” – 8x
(Q) Flat Washer
5/16” – 8x
(R) Spring Washer
1/4” – 36x
(S) Flat Washer
1/4” – 36x
(T) Corner Bracket
–12x
(U) Half-moon washer
5/16” – 8x
(V) Half-moon washer
1/4” – 12x
(W) Philips head Screw
#8x30mm - 28x
(X) Machine Screw
5/32”x12mm - 6x
TOOLS REQUIRED (Not included):
Philips Head Screwdriver

Date: 2016-Jun.-03
Rev: Page 4 of 15
ASSEMBLY INSTRUCTION STEPS:
1. Remove the metal rods from (D) and (B) as shown below. Put the rods and machine screws
aside for later use.

Date: 2016-Jun.-03
Rev: Page 5 of 15
2. Place (A) and (B) down on a soft, scratch-free surface such as a rug or carpet.
3. Thread (G) and (H) onto (A) and (B) in clockwise direction until tight, as seen in the
illustration below.
4. Attach (T) to (A) and (B). Make sure to assemble (T) in the correct direction as seen in the
illustration below.
O 12x
R 12x
S 12x
T 12x

Date: 2016-Jun.-03
Rev: Page 6 of 15
5. Attach (C) to (A) and (B) as shown below. Do not fully tighten the bolts at this time.
*Tip: See Image A for ease of assembly.
6. Attach E2 to (A &C) by aligning the pre-fixed wooden dowels on (E2) with the pre-drilled
holes on (C). Secure (E2) as shown below. Do not fully tighten the bolts at this time.
*Tip: See Image A (Page 6) for ease of assembly.
M 8x
P 8x
Q 8x
U 8x
N 1x
R 1x
S 1x
V 1x
Image A

Date: 2016-Jun.-03
Rev: Page 7 of 15
7. Loosely tighten (E2) to (A), as seen in the illustration below.
8. Attach (E1) and (E2) to (A&C) by aligning the pre-fixed wooden dowels on (E1) and (E2) with
the pre-drilled holes on (C).
9. Secure (E1) and (E2) as shown below. Do not fully tighten the bolts at this time.
O 2x
R 2x
S 2x
O 6x
R 6x
S 6x

Date: 2016-Jun.-03
Rev: Page 8 of 15
10. Secure the bottom part on (E1) & (E2) as shown below.
*Tip: See Image A (Page 6) for ease of assembly.
11. Carefully attach (D) in between (A) and (B) by spreading (A) and (B) as shown below.
12. Secure (D) to (A) and (B). Do not over tighten the bolts.
*Tip: See Image A (Page 6) for ease of assembly.
N 3x
R 3x
S 3x
V 3x
N 4x
R 4x
S 4x
V 4x

Date: 2016-Jun.-03
Rev: Page 9 of 15
13. Secure (D) to (A) and (B), as shown below. Do not over tighten the bolts.
14. Check the alignment and fully tighten all bolts at this time. Do not over tighten.
15. Lay (F) in between side rail as shown below.
16. Secure each slat by fastening (W) through the hole at the end of each slat and into the side
rail. Tighten the screws with a Phillips Head Screwdriver (Not included).
O 4x
R 4x
S 4x
W 28x

Date: 2016-Jun.-03
Rev: Page 10 of 15
17. Secure 4 pieces (K) (sold separately) to (E1) and (E2) as shown below.
18. Secure the rest 2 pieces (K) (sold separately) to (E1) and (E2) as shown below.
X 4x
X 2x