pottery barn kids ELLIOT CRIB User manual

Date: 2014-December-4
Rev: Page 1 / 11
pottery barn kids
ELLIOT CRIB
www.potterybarnkids.com

Date: 2014-December-4
Rev: Page 2 / 11
WARNING
•Do not use this crib if you cannot exactly follow the accompanying instructions.
•Do not use this crib for a child who can climb out of it, or who is taller than 89 cm.
•Do not place in or near this crib any cord, strap or similar item that could become wrapped around a child’s
neck.
•Do not place this crib near a window or a patio door where a child could reach the cord of a blind or curtain and
be strangled.
•Ensure that the crib is safe by checking regularly that every part is properly and securely in place before placing
the child in it. Do not use it if any parts are loose or missing or if there are any signs of damage. Do not
substitute parts. Contact Pottery Barn Kids if replacement parts or additional instructions are needed.
•Use a crib mattress that is no thicker than 15 cm and is of such a size that, when it is pushed firmly against any
side of the crib, it does not leave a gap of more than 3 cm between the mattress and any part of the sides of the
crib.
•Children can suffocate on soft bedding. Do not place pillows, comforters or soft mattresses in this crib.
04-000052-8
WARNING: Failure to follow these warnings and assembly instructions could result in
serious injury or death.
•Read all instructions before assembling crib. KEEP INSTRUCTIONS FOR FUTURE USE.
•Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.
•Infants can suffocate in gaps between the crib sides and a mattress that is too small.
•Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place additional padding under an
infant.
•To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless
otherwise advised by your physician.
•STRANGULATION HAZARD: Strings can cause strangulation! Do not place items with a string around a child’s
neck, such as hood strings or pacifier cords. Do not suspend strings over a crib or attach strings to toys.
•To help prevent strangulation tighten all fasteners. A child can trap parts of the body or
•clothing on loose fasteners.
•DO NOT place crib near window where cords from blinds or drapes may strangle a child
•FALL HAZARD: When child is able to pull to a standing position, set mattress to lowest position and remove
bumper pads, large toys and other objects that could serve as steps for climbing out.
•Stop using crib when child begins to climb out or reaches the height of 35 in. (89cm).
•Check this product for damaged hardware, loose joints, loose bolts or other fasteners, missing parts or sharp
edges before and after assembly and frequently during use. Securely tighten loose bolts and other fasteners.
DO NOT use crib if any parts are missing, damaged or broken. Contact Pottery Barn Kids for replacement parts
and instructional literature if needed. DO NOT substitute parts.
•DO NOT use a water mattress with this crib.
•Replace teething rail if damaged, cracked, or loose. NOTE: This is only for cribs with teething rails
•If refinishing, use a non-toxic finish specified for children’s products.
•Do not remove the metal brackets from the mattress base after installation. NOTE: This is only for cribs
supplied with a wooden mattress base.
• Follow warnings on all products in a crib.
04-000056-7

Date: 2014-December-4
Rev: Page 3 / 11
CAUTION: ANY MATTRESS USED IN
THIS CRIB MUST BE AT LEAST 27 ¼” (69
CENTIMETERS) BY 51 5/8” (131
CENTIMETERS) WITH A THICKNESS NOT
EXCEEDING 6” (15 CENTIMETERS)
THIS CRIB CONFORMS TO APPLICABLE REGULATIONS PROMULGATED BY THE CONSUMER
PRODUCT SAFETY COMMISSION.
04-000094-3
IMPORTANT SAFETY INSTRUCTIONS:
•Please read all instructions carefully before assembling.
•For your safety, assembly by two or more adults is recommended.
•Keep instructions for future use.
•Use only vendor supplied hardware to assemble. Using unauthorized hardware could jeopardize the structural
integrity of the item.
•Do not remove warning labels from the crib. Labels are permanent and not designed to be removed.
PRE-ASSEMBLY:
•Remove all parts and hardware from the box and place them on a carpet, or scratch-free work surface, as this
will avoid damaging parts during assembly. The shipping box provides an ideal work surface.
•To avoid accidentally discarding small parts or hardware, do not dispose of any packaging or contents of the
shipping carton until assembly is complete.
•Use the parts and hardware lists below to identify and separate each of the pieces included.
•The illustrations provided allow for easier assembly when used in conjunction with the assembly instructions.
•The use of power tools to aid in assembly in not recommended. Power tools can damage hardware and split
wood.

Date: 2014-December-4
Rev: Page 4 / 11
PARTS INCLUDED
PART 1). HEADBOARD (1x)
PART 2). FRONT GATE (1x)
PART 3). LEFT END PANEL (1x)
PART 4). RIGHT END PANEL (1x)
PART 5). MATTRESS BASE (1x)
PART 6). APPLIQUE (2x, FOR FULL BED ONLY)
HARDWARE INCLUDED:
(A) Allen Key – 1x
1
x
(F) Left Bracket – 2x
2
x
(G) Right Bracket – 2x
2
x
(H) Acorn Nut (M6) – 8x
(I) Wrench – 1x
(B) Bolt (M6 x 50mm) – 4x
2
x
(C) Bolt (M6 x 40mm) – 4x
2
x
(D) Bolt (M6 x 20mm) – 4x
4
x
(E) Bolt (M6 x 17mm) – 8x
1
2
3
4
5
6
6

Date: 2014-December-4
Rev: Page 5 / 11
KEEP THE BELOW HARDWARE FOR FUTURE USE WHEN CONVERTING TO A FULL SIZE BED USING
METAL FRAME (SOLD SEPARATELY).
(A) Allen Key – 1x
1
x
(I) Wrench – 1x (K) Hexagon Nut (M6) – 4x (L) Spring Washer (M6) – 4x
(M) Flat Washer (M6) – 4x
(N) Bolt (M6 x 55mm) – 6x
6
x
(O) Bolt (M6 x 20mm) – 4x
4
x

Date: 2014-December-4
Rev: Page 6 / 11
ASSEMBLY INSTRUCTIONS
1. Attach Left and Right Brackets (F&G) to the Mattress Base (PART 5) using (8x) Bolt (E). Make sure the
brackets point outwards. Tighten using Allen Key (A). Note: Do not remove the metal brackets (F&G) from the
mattress base upon installation.
2. Cover the protruding parts of the inserted Bolts (E) with the Acorn Nuts (H) at the back of the Mattress Base
and from inside of the frame, as seen in the illustration below. Tighten using Wrench (I).
3. Place Front Gate (PART 2) on a soft and scratch-free work surface with pre-drilled holes facing upward. Attach
Left/Right End Panel (PART 3 & 4) to Front Gate (PART 2). Insert (2x) Bolt (C) through the holes at top and
bottom of each End Panel into corresponding metal inserts at top and bottom of the Front Gate as shown
below. Secure all bolts with Allen key (A). Do not fully tighten bolts (C) at this point to make installation of the
Mattress Base and the remaining Headboard easier.
2
3
4
Arrow sticke
r side down. Arrow points inside.
Côté avec étiquette à flèche vers le bas.
Flèche pointée vers l'intérieur.
C
2
x
4x
E 8x F
2
x
2x G
2
x
2x H
8
x
8x
(G)
(F)
(F)
(G)
3
(A)
(E)
(G)
(H)
(I)

Date: 2014-December-4
Rev: Page 7 / 11
Note: The Mattress Base (PART 5) should be at the highest level (Level 1) when the child is born. It must
be at the lowest level (Level 3) before the child can stand up. Before installing the Mattress Base (PART
5), please ask the customers at which height they want it installed.
4. Determine the desired height of the Mattress Base. Place the Mattress Base into the crib using two adults,
with care not to scratch the finish. Attach the Mattress Base (PART 5) to the Front Gate (PART 2) using (2x)
Bolt (D) and tighten with Allen Key (A). Do not fully tighten Bolts (D) at this point.
5. Attach Headboard (PART 1) to Left/Right End Panel (PART 3 & 4) using (4x) Bolt (B). Make sure the (4) holes
at corners of Headboard (PART 1) align with holes on End Panels (PART 3 & 4) as shown below. Make sure to
use the upper holes on posts. Then fix the remaining two brackets to the Headboard (PART 1) at the same
level as in previous step using (2x) Bolt (D) and tighten with Allen Key (A).Tighten all bolts including also the
ones from previous step using Allen Key (A) .
(A)
(A)
(D)
5
D
4
x
2x
B
2
x
4x
D
4
x
2x
/ Niveau 3
/ Niveau 2
/ Niveau 1

Date: 2014-December-4
Rev: Page 8 / 11
Nous vous remercions de votre achat
magasins | catalogue | www.potterybarnkids.com
É-U 1.800.290.8181
6. To change the position of the Mattress Base (PART 5), unscrew Bolts (D), line up the Mattress Base (PART 5)
with the holes at the desired height, and re-attach the Mattress Base (PART 5) using the same Bolts (D).
7. Check alignments and fully tighten all connections at this time.
8. Assembly is now complete.
9. Place the assembly instructions back into the envelope mounted on the mattress base for future reference.
CARE INSTRUCTIONS
•Dust often using a clean, soft, dry, lint-free cloth.
•Blot spills immediately, and wipe with a clean, damp cloth.
•We do not recommend the use of chemical cleansers, abrasives, or furniture polish on our lacquered finish.
•If the crib is to be stored, store in cool dry place and carefully package all original hardware to protect from loss
or damage.
•Check fasteners periodically for tightness. DO NOT over tighten, as this may cause distortion or breakage.
•Parents should ensure a safe environment for the child by checking the crib regularly that every component is
properly and securely in place, before placing the child in the product.
Thank you for your purchase.
stores | catalog | www.potterybarnkids.com
USA 1.800.290.8181
(A)
(D)

Date: 2014-December-4
Rev: Page 9 / 11
NOTES:
•As the Elliot 3-in-1 Crib is designed to grow with your child, please retain the instructions as well as all hardware
for future use. Always keep all small parts and hardware out of the reach of small children.
•Please see instructions below when converting to a toddler or Full bed. Based upon your selection, there will be
different instructions and additional pieces needed for these conversions. Please read carefully and follow all
instructions.
1. Headboard with Metal Frame
*Metal Frame sold separately
*See assembly instruction on page 10
2). Headboard/Front Gate with Metal Frame
* Metal Frame sold separately
* See assembly instruction on page 11
3). Crib with Toddler Bed Conversion Kit
* Conversion Kit sold separately
* Refer to assembly instruction shipped with
Toddler Bed Conversion Kit
6
6
2
6
6

Date: 2014-December-4
Rev: Page 10 / 11
ASSEMBLY INSTRUCTIONS TO CONVERT CRIB INTO FULL SIZED BED (headboard only) WITH METAL
FRAME (sold separately).
With the addition of a Metal Frame (sold separately), your Elliot 3-in-1 Crib Headboard can be utilized as a full sized
headboard. Follow the instructions below with 2 Adults:
1. Disassemble your crib or toddler bed and set all pieces and hardware aside in an organized manner.
2. Assemble the Metal Frame according to the instructions included with the frame.
3. Place the Appliqué (PART 6) over the pre-drilled hole on headboard posts and insert (2x) Bolt (N) from the other
side of the posts to secure the (2x) Appliqué using Allen Key (A).
4. Hold the Elliot 3-in-1 Crib Headboard upright near the desired location in the room.
5. Insert (4x) Bolt (N) into pre-drilled holes in the bottom back side of both legs. Attach and align the Metal Frame
onto Headboard leg bolts. Slide a Flat Washer (M), Spring Washer (L) onto each bolt from the other end and
tighten with a Nut (K), using Allen Key (A) and Wrench (I).
6
x
(N)
(K)
(M)
(L)
(I)
(N)
6
1
(N) Bolt M6x55mm – 6x
(K) Hexagon Nut
(M6) – 4x
(L) Spring Washer
(M6) – 4x
(M) Flat Washer
(M6) – 4x
2x
2x
Part 6). Applique – 2x

Date: 2014-December-4
Rev: Page 11 / 11
ASSEMBLY INSTRUCTIONS TO CONVERT CRIB INTO FULL SIZE BED (Headboard & Front Gate only) WITH
METAL FRAME (sold separately).
With the addition of a Metal Frame (sold separately), your Elliot 3-in-1 Crib Headboard and Front Gate can be
utilized as full sized headboard and footboard. Disassemble your crib and set all pieces and hardware aside in an
organized manner. Follow the instructions below with 2 adults:
1. Disassemble your crib or toddler bed and set all pieces and hardware aside in an organized manner.
2. Assemble the Metal Frame according to the instructions included with the frame.
3. Place the Appliqué (PART 6) over the pre-drilled holes on headboard posts and insert (2x) Bolt (N) from the
other side of the posts to secure the (2x) Appliqué using Allen Key (A).
4. Hold the Crib Headboard (PART 1) upright near the desired location in the room.Insert (4x) Bolt (N) into
pre-drilled holes in the bottom back side of both legs. Attach and align the Metal Frame onto Headboard leg
bolts. Slide a Flat Washer (M), Spring Washer (L) onto each bolt from the other end and tighten with a Nut (K),
using Allen Key (A) and Wrench (I). Secure Front Gate (PART 2) to the Metal Frame by using (4x) Bolts (O).
6
x
(N)
(K)
(M)
(L)
(I)
2
(N)
6
1
(N) Bolt M6x55mm – 6x (O) Bolt M6x20mm – 4x
(K) Hexagon Nut
(M6) – 4x
(L) Spring Washer
(M6) – 4x
(M) Flat Washer
(M6) – 4x
2x
2x
Part 6). Applique – 2x
4
x