PotteryBarn AVA DOUBLE PED DESK User manual


Date:19‐May‐16www.potterybarn.com  Page1of7
Rev:  



AVA DOUBLE PED DESK






Date:19‐May‐16www.potterybarn.com  Page2of7
Rev:  
Important Safety Instructions:
Please read all instructions carefully before assembling.
For your safety, assembly by two or more adults is strongly recommended.
Keep instructions for future use.
Use only vendor supplied hardware to assemble. Using unauthorized hardware could jeopardize the structural
integrity of the item.
Pre-assembly:
Remove all parts and hardware from the box and lay out on a clear carpeted or scratch-free work surface, as
this will avoid damaging parts during assembly. The shipping box provides an ideal work surface.
Do not dispose of any packaging or contents of the shipping carton until assembly is completed to avoid
accidentally discarding small parts or hardware.
Use the parts and hardware lists below to identify and separate each of the pieces included.
The illustrations provided allow for easier assembly when used in conjunction with the assembly instructions.
The use of power tools to aid in assembly is not recommended. Power tools can damage hardware and split
wood.
PartsIncluded:
(A) Table top 1x
(B) Left cabinet 1x
(C) Right cabinet 1x
(D) Back rail 1x
(E) Cross rail 4x
(F) Front rail 2x







Hardware Included:

(G)
Flat Head Bolt
Ø1/4”x5/8”
16x
(H)
Bolt
Ø 1/4”x1-1/8”
8 x
(I)
Bolt
Ø 1/4”x5/8”
12x
(J)
Allen Wrench
1 X
E
D
E
E
C
A
B
EF
F


Date:19‐May‐16www.potterybarn.com  Page3of7
Rev:  
Assembly Instruction Steps:
1. Align two cabinets and place the Table top (A) onto the base as shown, push the Table top backward until
both the pre-fixed wood rails latch up.
2. Unscrew the handle from interior of drawer box, and then screw it onto exterior of drawer using Phillips Head
Screwdriver as shown.
A
B
C
A
B
C
2X
2X


Date:19‐May‐16www.potterybarn.com  Page4of7
Rev:  
3. Fixed the Top (A) to the Cabinet (B) and Cabinet (C) by using four Bolts (H) and Allen Wrench (J) as shown.
4. Remove the upper drawer of Cabinet (B) and Cabinet (C) by pressing the plastic locks on the side drawer
slides upwards and downwards as shown while pulling drawer out.
A
B
C
H
J
B
C
4X


Date:19‐May‐16www.potterybarn.com  Page5of7
Rev:  
5. Secure the Table top (A) by using four Bolts (H) and Allen Wrench (J). Fully tighten Bolts as shown.
6. Assemble the Metal Frame as shown by using Flat Head Bolt(G) and Allen Wrench(J). Fully tighten all Bolts.




A
B
C
J
H
4X
D
E
E
E
E
F
F
G
J
16X


Date:19‐May‐16www.potterybarn.com  Page6of7
Rev:  
7. Fully extend the drawer slides, align the slides on the drawer boxes with the slides on desk top and install the
drawers back. Push and pull the drawer back and forth a few times until it is locked firmly.
8. Place the Cabinet on a soft, clean surface on its side. Attach the metal base to the Cabinet by using Bolt (I)
and Allen Wrench (J).
B
C
B
C
I
J
12X
NOTE: Make sure the
metal frame is flush
with cabinet.


Date:19‐May‐16www.potterybarn.com  Page7of7
Rev:  
Adjusting the levelers:
Due to an uneven floor, the furniture may not sit level due causing it to wobble. If the furniture wobbles, determine
which corner does not touch the ground correctly. With two people follow these steps:
1) Carefully elevate the item slightly to provide access to the levelers attached to the bottom.
2) Turn the levelers until adequate contact will be made with the floor. Gently set down the piece and check
stability.
3) Repeat steps until furniture sits firmly on the ground.
Care Instructions:
Dust often using a clean, soft, dry and lint-free cloth.
Blot spills immediately and wipe with a clean, damp, cloth.
We do not recommend the use of chemical cleansers, abrasives or furniture polish on our lacquered finish.
Hardware may loosen over time. Periodically check to make sure all connections are tight.
Re-tighten if necessary.
Thankyouforyourpurchase
Stores|catalog