PotteryBarn Canopy Bed Frame User manual


Date:8‐Jun‐15www.potterybarn.com  Page1of12
Rev:  
















Canopy Bed Frame







Date:8‐Jun‐15www.potterybarn.com  Page2of12
Rev:  


Important Safety Instructions:
WARNING: Do not allow children to climb on, pull on, or hang from canopy. Failure to follow these
instructions can result in serious bodily injury.
Please read all instructions carefully before assembling.
For your safety, assembly by 4 or more adults is strongly recommended.
Assemble the frame in the desired place.
Keep instructions for future use.
Use only vendor supplied hardware to assemble. Using unauthorized hardware could jeopardize the structural
integrity of the item.
Pre-assembly:
Remove all parts and hardware from the box and lay out on a clear carpeted or scratch-free work surface, as
this will avoid damaging parts during assembly. The shipping box provides an ideal work surface.
Do not dispose of any packaging or contents of the shipping carton until assembly is completed to avoid
accidentally discarding small parts or hardware.
Use the parts and hardware lists below to identify and separate each of the pieces included.
The illustrations provided allow for easier assembly when used in conjunction with the assembly instructions.
The use of power tools to aid in assembly is not recommended. Power tools can damage hardware and split
wood.
Hardware Included:
(a)
Bolt
M6 x 16mm
50x
(b)
Round Head Bolt
M4 x 6mm
4x
(c)
Long Bolt
M6 x 65mm
4x
(d)
Flat Washer
4x
(e)
Nut
2x
(f)
4mmAllen Wrench
1x
(g)
Open Wrench
1x
(h)
2mmAllen Wrench
1x
(i)
Mounting Screw
M4 x 50mm
2x
( j )
Toggle
2x
(k)
Toggle Screw
2x


Date:8‐Jun‐15www.potterybarn.com  Page3of12
Rev:  


Parts Included:
Part Description QTY
(A) Rail A 1x
(B) Rail B 1x
(C) Rail C 1x
(D) Rail D 1x
(E) Rail E 6x
(F) Rail F 2x
(G) Post 4x
(H) Corner 4x
(I) Mounting Bracket 2x
(J) Rail J 4x
(K) Rail K 2x
(L) Rail L 2x
(M) Rail M 2x
(N) Rail N 2x
Tools Required
(Not included):
Ladders
Stud finder
Pencil
Phillips Head Screwdriver
E
J
I
E
J
A
B
D
C
E
E
E
E
F
F
G
G
G
G
H
H
H
H
I
J
J
K
L
M
N


Date:8‐Jun‐15www.potterybarn.com  Page4of12
Rev:  


Assembly Instruction Steps:
1. Attach Rail (A) to Rail (C) as shown, choose the correct holes for your bed size, insert Bolt (a) and tighten with
4mm Allen Wrench (f). Repeat this step for Rail (B&D) and 2 sets of Rail (E&F).
A
B
C
D
F
E
a
a
2X
1X
1X
The two holes are for Queen size
The two holes are for CK size
The two holes are for King size
Choose the correct holes for your bed size as shown


Date:8‐Jun‐15www.potterybarn.com  Page5of12
Rev:  


2. Attach Rail (E) to Rail (J) as shown, choose the correct holes for your bed size, insert Bolt (a) and tighten with
4mm Allen Wrench (f). Repeat this step to have 4 groups of Rail (E&J).
E
J
aa
E
J
The two holes are for Queen and King size
The two holes are for CK size
Choose the correct holes for your bed size as shown


Date:8‐Jun‐15www.potterybarn.com  Page6of12
Rev:  


3. Attach the Assembly (A&C) and (B&D) to Assembly (E&J) as shown, insert Bolt (a) and tighten with 4mm Allen
Wrench (f).
4. Attach Post (G) to the assembly in step 3 as shown, insert Bolt (a) and tighten with 4mmAllen Wrench (f).
aa
a
a
a
a
a
a
C
E
J
E
J
A
B
D
G
aa
aa
a
a
a
a
G
G
G


Date:8‐Jun‐15www.potterybarn.com  Page7of12
Rev:  


5. Insert Mounting Bracket (I) to Rail (E) and Rail (F) as shown. NOTE: Screw or unscrew the small bolt on the
bracket with 2mm Allen Wrench (h) to tighten or loosen the bracket on the rail.
Attach Corner (H) to the Group (E&F) and Group (E&J). Insert Bolt (a) and tighten with 4mmAllen Wrench (f).
6. Carefully lift assembly in step 5 with 4
persons, and then attach it to the post
as shown.
h
aa
aa
aa
aa
E
E
J
J
H
H
H
H
E
F
E
F
I
I
Important Note: Make
sure the mounting
bracket side toward
the wall.


Date:8‐Jun‐15www.potterybarn.com  Page8of12
Rev:  


7. Rails (K&L) are for Queen Size, Rails (M&N) are for King & CK Size. Choose the correct rails for your bed.
(Illustration only shows Queen Size)
Attach Rail (K) to Rail (L) as shown, insert Round Head Bolt (b) and tighten with Phillips Head Screwdriver
8. Secure the group (K&L) with Canopy Bolt (a), Nut (e) and tighten with 4mm Allen Wrench (f) and Open Wrench
(g). DO NOT fully tighten the bolt in this step.
K
K
L
L
b
b
df
L
L
K
K
a
a
e
g


Date:8‐Jun‐15www.potterybarn.com  Page9of12
Rev:  


9. Attach the Canopy to the top corner with 4 persons as shown, insert Long Bolt (c) thru Flat Washer (d) and
tighten with 4mm Allen Wrench (e). Finally fully tighten all bolts.
l
l
l
l
c
d
c
c
d
d
d
c


Date:8‐Jun‐15www.potterybarn.com  Page10of12
Rev:  


Mount The Canopy To The Wall:
NOTE: For safe mounting it is essential to use the proper hardware for your wall type. The hardware included is
meant for drywall or wood stud mounting only. If walls are concrete, brick or plaster, please consult your local
hardware store for assistance in selecting the appropriate hardware. Mount to wood studs whenever possible.
1. Move the Canopy Frame to the desired place beside the wall. And make sure the mounting bracket against the
wall.
2. Use a sharp pencil or a screw to mark the wall through the hole located in the Bracket. This mark is the
insertion mark for the provided hardware (Mount to wood studs whenever possible).
3. The provided Toggle (j) is needed for drywall applications, but cannot penetrate into wall studs (wood).
Therefore, we recommend that you use a stud finder to determine if any of the insertion marks align with a wall
stud. If so, only a Mounting Screw (i) will be used at that mark. If not, then both a Toggle (j) and a Toggle
Screw (k) will be used.