PotteryBarn Studio Wall Shelf User manual


Date:30‐Sep‐15www.potterybarn.com  Page1of7
Rev:  
































STUDIO WALL SHELF







Date:30‐Sep‐15www.potterybarn.com  Page2of7
Rev:  


Important Safety Instructions:
Please read all instructions carefully before assembling.
For your safety, assembly by two or more adults is strongly recommended.
Keep instructions for future use.
Use only vendor supplied hardware to assemble. Using unauthorized hardware could jeopardize the structural
integrity of the item.
Pre-assembly:
Remove all parts and hardware from the box and lay out on a clear carpeted or scratch-free work surface, as
this will avoid damaging parts during assembly. The shipping box provides an ideal work surface.
Do not dispose of any packaging or contents of the shipping carton until assembly is completed to avoid
accidentally discarding small parts or hardware.
Use the parts and hardware lists below to identify and separate each of the pieces included.
The illustrations provided allow for easier assembly when used in conjunction with the assembly instructions.
The use of power tools to aid in assembly is not recommended. Power tools can damage hardware and split
wood.
Parts Included:
(A) Left legs 1x
(B) Right legs 1x
(C) Top shelf 1x
(D) Second shelf 1x
(E) Third shelf 1x
(F) Fourth shelf 1x
(G) Bottom shelf 1x















C
A
B
D
E
F
G


Date:30‐Sep‐15www.potterybarn.com  Page3of7
Rev:  


Hardware Included:
(H)
Allen key

4mm
1x
(I)
Bolt
Dia. 1/4”x1-1/4”
10x
(J)
Spring Washer

Dia. 5/16*14mmL
10x
(K)
Toggle Bolt
2x
(L)
Long Screw
2x
(M)
Wood Screw
#8 x 2-1/2”L
2x
Tools Required( Not included):
Philips Head Screwdriver Pencil Stud Finder
Assembly Instruction Steps:
1. Attach Top Shelf (C) to Right Leg (B) using Sping Washer (J) and Bolt (I), Securely tighten all bolts with Allen
Key (H). Repeat step with the remaining four shelves (D, E, F, G).
H
I
C
D
E
F
G
B
J


Date:30‐Sep‐15www.potterybarn.com  Page4of7
Rev:  


2. Attach the remaining leg (A) to assembly as shown. Insert Bolt (I) thru Spring Washer (J) , securely tighten all
bolts with the Allen Key (H).
H
J
IG
F
E
D
C
A


Date:30‐Sep‐15www.potterybarn.com  Page5of7
Rev:  


3. Adjusting the levelers:
Due to an uneven floor, the furniture may not sit level due causing it to wobble. If the shelf wobbles determine
which corner does not touch the ground correctly. With two people follow these steps:
(1) Carefully elevate the item slightly to provide access to the levelers attached to the bottom.
(2) Turn the levelers until adequate contact will be made with the floor. Gently set down the piece and check
stability.
(3) Repeat steps until furniture sits firmly on the ground.


Date:30‐Sep‐15www.potterybarn.com  Page6of7
Rev:  


MOUNT THE SHLEF TO THE WALL- The Shelf must be secured to the wall.
NOTE: For safe mounting it is essential to use the proper hardware for your wall type. The hardware included is
meant for drywall or wood stud mounting only. If walls are concrete, brick or plaster, please consult your local
hardware store for assistance in selecting the appropriate hardware. Mount to wood studs whenever possible.
1. Move the shelf to the desired placement on the wall. Use a sharp pencil or a screw to mark the wall through the
holes on top shelf and bottom shelf as shown. These marks are the insertion marks for the provided hardware.
2. The provided toggle bolt (K) is needed for drywall applications, but cannot penetrate into wall studs (wood)
Therefore, we recommend that you use a stud finder to determine if any of the insertion marks align with a wall
stud. If so, only a wood Screw (M) will be used at that mark. If not, then both a Toggle Bolt (K) and a Long screw
(L) will be used.
3. For drywall mounting: using a screwdriver to engage a Toggle Bolt (K) and position the toggle bolt tip against
the wall at the insertion mark. Gently push the toggle bolt into the wall as you rotate the toggle bolt clockwise.
Continue rotating until the large flange of the toggle bolt is flush with the wall.
4. Once the Toggle Bolt (K) is installed into the wall at the marked locations, return the shelf to the wall. Use a
screwdriver to secure the Shelf through long screw (L) into the toggle bolt.

K
L
K
L


Date:30‐Sep‐15www.potterybarn.com  Page7of7
Rev:  


For stud mounting: Use a screwdriver to secure the Shelf through Wood Screw (M) at the marked locations,
simply drive down Wood Screw (Y) for securing.











Care Instructions:
Dust often using a clean, soft, dry and lint-free cloth.
Blot spills immediately and wipe with a clean, damp, cloth.
We do not recommend the use of chemical cleansers, abrasives or furniture polish on our lacquered finish.
Hardware may loosen over time. Periodically check to make sure all connections are tight.
Re-tighten if necessary.
Thankyouforyourpurchase
Stores|catalog
M
M