PotteryBarn Ava User manual

090912
1/5
Ava Display Desk Table
Assembly Instructions
Pre-Assembly:
•Please read all instructions carefully before starting assembly of the Ava Display Desk Table.
•To avoid unintentionally discarding any small parts or hardware, keep all packing materials until the product is
completely assembled.
•Use the parts and hardware lists to identify and separate each of the components included.
•To protect the product from scratching, place the product components on a flat, clean floor with either the foam
or the cardboard carton
•For your safety and ease, assembly by two adults is recommended.
Parts Included:
A - Top Frame ( 1x )
B -X-Base ( 2x )
C - Stretcher ( 1x )
D - Wedge ( 2x )
E - Top Panel ( 1x )
F - Glass Top ( 1x )
Hardware Enclosed:
G-Flat Washer (4x) H-Lock Washer (4x)
I- Short Allen Bolt (4x)
(M6 x 40 mm)
J - Allen Key ( 1x )
(4mm)
K-Flat Washer (10x) L-Lock Washer (10x)
M - Long Allen Bolt (4x)
(M8 x 75 mm)
N - Allen Key ( 1x )
(5mm)
O - Short Allen Bolt (6x)
(M8 x 32 mm)
P - Plastic Shim ( 6x )

090912
2/5
L
C
Assembly Instructions:
1. Place the Top Frame (A) upside down on a carpet, or on the foam from the shipping box. Attach the X-Bases
(B) to the Top Frame (A) by inserting the wood dowels (on the frame) into the pre-drilled holes on the X-Base.
Insert the Short Allen Bolt (I) through the Small Lock Washer (G), Small Flat Washer (F), and through the pre-
drilled holes on the frame. Use the Allen Key (J) to tighten the 2 bolts (I) into the nuts embedded in the X-
Base.
2. Attach the Stretcher (C) to the X-Base (B) by inserting the wood dowel, at the two ends of the stretcher, into
the pre-drilled hole at the center of the X- base. Insert the Long Allen Bolt (M) through Large Lock Washer (L),
Flat Washer (K), and pre- drilled holes on the X-Base (B). Use the Allen Key (N) to tighten the 2 bolts (M) into
the nuts embedded in the Stretcher. Hold the other end of the Stretcher for the next assembly.

090912
3/5
A
E
B
B
L
O
3. Repeat Step 1 and Step 2 to assemble the X-Base (B), as shown in the illustration below.
C
BI
L
4. Turn the assembled table frame upright. Attach the Top Panel (E) to the table frame by inserting the pre-drilled
holes on the underside of the Top Panel into the wood dowels on the X- Base.
Insert the Short Allen Bolt (O) through the Large Lock Washer (L), Large Flat Washer (K), and through the pre-
drilled holes on the Top Frame (A) and X- Base (B). Then use the Allen Key (N) to tighten the 6 bolts (O) into
the nuts embedded on the underside of the Top Panel (E).

090912
4/5
5. Attach the 2 Wedges(D) to the X-Base (B) by inserting the wood dowels (on the Wedge) into the pre-drilled
holes on the X-Base.
6. Adjust the levelers under the legs of the X- Base, if the desk frame and base do not sit level.

090912
5/5
7. Remove the Plastic Shim (P) from the paper holder. Stick the plastic shim to the support rails on the Top Panel
(E), as shown in the illustration below. Carefully fit the Glass Top (F) into the Top Panel (E). Properly adjust the
position of Glass Top to ensure all edges are aligned before use.
F
8. Assembly is complete.
Care Instructions:
•For daily cleaning, simply wipe with a soft, damp cloth and wipe dry immediately.
•Do not clean product surface with unknown chemicals or harsh cleaning agents.
•Do not sit on the desktop.
•Regularly check and tighten all the Allen Bolts to ensure the desk base stays firmly in position.
Thank you for your purchase
stores | catalog | www.potterybarn.com