PotteryBarn Floor Mirror with Clothing Rack User manual

P:1/2
Floor Mirror with Clothing Rack
Assembly & Mounting Instructions
Component Included:
A. (1) Mirror
B. (1) Upper Shelf (with brackets)
C. (1) Lower Shelf (with brackets)
D. (1) Supporting Rod
Hardware for Assembly:
E. (4) Dowel
F. (6) Wood Screw
G. (1) Bolt
Hardware for Mounting:
H. (3) Mounting Screw
I. (3) Drywall Anchor
TOOLS REQUIRED: Phillips Screwdriver, Pencil, Level, Stud Finder.
Pre-assembly:
-Please read all instructions carefully before getting started.
-Remove all parts and hardware from carton box and lay them out on a clear workspace.
-Do not discard any contents until after assembly / installation is completed to avoid accidentally discarding small
parts or hardware.
-As this item is quite big and heavy, two people are required for the assembly and mounting.
-The use of power tools to aid in assembly is not recommended.
-The illustrations provided allow for easier assembly when used in conjunction with the assembly instructions.
ASSEMBLY INSTRUCTIONS:
1. Place Mirror (A) face down on a
flat, protected surface as shown,
insert a Dowel (E) into each of the
four dowel holes at the back of
mirror.
2. Position each Upper Shelf (B) and
Lower Shelf (C) at its location and
aligning with the dowels. Note that
the Upper shelf includes one more
hole in the middle that is to
assemble with Supporting Rod (D).
Make sure that the brackets on the
shelves are all facing to the bottom
of the mirror.
3. Secure the brackets of each shelf
to the back of mirror using
provided Wood Screws (F) and
fasten with a Phillips screwdriver.
4. Position Supporting Rod (D) under
Upper Shelf (B) at the middle
location. Attach the round end of
the rod to the shelf using Bolt (G). Use a Phillips screwdriver to rotate the bolt clockwise until tight.
The hardware (H/ I) is meant for drywall or stud construction
only. For other wall types, please consult your local hardware
store for assistance in selecting the appropriate hardware.
Dowel hole (6mm)
Step. 4
Step. 3
Step. 5

P:2/2
5. Attach the flat end of Supporting Rod (D) to the back of mirror using the remaining two Wood Screws (F). Tighten
with a Phillips screwdriver.
6. Position the assembly upright and it now is ready for wall mounting.
MOUNTING INSTRUCTIONS:
This item is meant to be set on the floor and simultaneously attaching to a wall using provided mounting
hardware. DO NOT hang this item directly from the wall.
1) With the help of another person, position the mirror upright at a desired location on the floor so that the backs of
the shelves touch to a wall. Using a pencil, mark the wall through each of the four brackets located at the rear side
of item as shown (see FIG-1). Move the mirror aside. The resulting marks on the wall are the insertion points for
the mounting hardware.
2) Use a stud-finder to determine if there is a wall stud located at either insertion mark. If a mark aligns with wall stud,
leave the mark to Step #4 as you will only install a screw (H) at that location.
3) For marks that do not align with a stud, first
install the anchors (I) into the wall. To do this,
use a Phillips screwdriver to engage an
anchor and then position the anchor tip
against the wall at one of the marks. Rotate
the anchor clockwise as you firmly push it into
the wall. The anchor will drive itself into the
wall like a large screw. Continue rotating until
the anchor’s head is flush with the wall surface.
Do not over-tighten.
4) Once the anchors are in place, Move the
mirror back to the location so that the holes on
the brackets align with either installed anchors
or pencil marks (stud-aligned positions). Use
the screwdriver to secure a screw (H) through
each hole and into either an installed anchor
(see Fig.2), or directly into the wall. Rotate
each screw clockwise until tight.
The product now is secured to the wall.
CARE INSTRUCTIONS:
-Wipe with a soft, dry or slightly damp cloth.
-To protect the finish, do not apply household cleaners or abrasives.
Thank you for your purchase!
Stores | Catalog | www.potterybarn.com
NOTE:Maximumtotalweightcapacityforthisproductis
50pounds(22.7Kg),(25pounds(11.3Kg)maximumper
shelf/horizontalsurface).
FIG-1
FIG-2