Power Drive P1000FC Programming manual

Battery Backup DC Control System
For Use with Gravity
Failsafe Fire Curtains
P1000FC
Quick Start Instructions Iss.7 2021

Important Information on the PMaC P1000
In the event of a site having no permanent mains supply it is still possible to set up and commission the curtain. The P1000 has a built in battery pack which is capable of
operating the motor without mains being available. Where it is known beforehand that a permanent mains supply is not available, before visiting site the P1000 should be
given a full charge for approx 7 hours. To do this connect a temporary mains feed and fit the battery fuse. Once charge has been completed remove the battery fuse.
Useful Information P1000
Working Temp -15 to +50 C
Other Information
Standby time
Dimensions 460x306x130mm
Internal Voltage 24V
Panel Batteries 2 x 12v 3.2 AH or equivalent
Environment
IP Rating IP50
Key Number
Humidity 20 - 90% Non Condensing
Enclosure to be sited in dry location
Supply Voltage
Panel Supply Voltage 90-264Vac 47-63Hz Input. Fused 5A
Material Steel
Enclosure

L E N
Fire Curtain Control
owerdrive P1000FC
BATTERY TEST
OPEN
CLOSE
CLOSING
OPENING
RELAY 1 ACTIVE
RELAY 2 ACTIVE
RELAY 3 ACTIVE
RELAY 4 ACTIVE
RELAY 5 ACTIVE
FAULT CONDITION
POWER
BATTERY TEST FAIL
AUTOTEST FAIL
ALARM 1 ACTIVE
ALARM 2 ACTIVE
AUTOTEST
Isolate Main Supply
Before Opening
PMaC P1000 Lid Removal

Open
Emer. Retract
Com
Close
Com
Fire
Access
Alarm
Input 2
Alarm
Input 1
Test
SC
Battery Fuse 7.5A
Automotive Blade
OSE
Receiver
OSE
Transmitter
SELECT
Prg UP
Prg DOWN
L
5A
E N
Incoming Mains Supply
1
3
5
8
9
7
All connections to the P1000 should be undertaken
with the mains supply turned off and the battery
fuse removed.
Failure to remove power may result in damage to the
equipment.
1. Connect 230V AC to the incoming mains supply
terminal block - Fused at 5A. Do not turn on yet.
2.Ensure 7.5A battery fuse is removed from the board
and the LCD display is blank.
3. Connect motor to the board. Ensure wire numbers
match the terminal numbers.
4. Connect the batteries together with the fused
link and ensure the 10A battery protection fuse is
fitted.
5. Ensure either the monitoring resistors are fitted to
the inputs or the monitored devices i.e. alarm input,
fire access, emergency retract are fitted
(see page 8-14)
6. Fit 7.5A BATTERY fuse. The LCD will briefly display
the model number and serial number.
7. Turn on the mains supply
8. Briefly turn the key switch and check the running
direction of the curtain matches what the display
reads.
i.e. Curtain closes = Push To Run Close
If the running direction is incorrect follow the
procedure to swap the Orientation in the menus
see page 25
DO NOT SWAP WIRES AROUND
9. Set the Open and Close limits ON the motor with the
adjuster tool supplied. Do not use a drill to twist the limits. Ensure the
bottom limit is set with the bottom bar fully to the floor.
.
Basic Installation of P1000
26
4
RELAY 4
24V 0V
RELAY 5
24V 0V

Open
Emer. Retract
Com
Close
Com
Fire
Access
Alarm
Input 2
Alarm
Input 1
Test
SC
Battery Fuse 7.5A
Automotive Blade
OSE
Receiver
OSE
Transmitter
SELECT
Prg UP
Prg DOWN
L
5A
E N
Incoming Mains Supply
14
12
10
15
11
13
1918
18 19
17
16
11
Firefighter Access
Curtain Override
15
10
20
21
P1000 Connections
10. Emergency retract switch (user escape)
11. Key switch connection from lid. To fit
external key switch remove existing switch
connections
12. Test Input
13. Alarm Input 1 - Master Alarm
14. Alarm Input 2 - Secondary Alarm
15. Fire access input (firefighter access)
16. OSE Optical beam input
17. Volt free c/o relay outputs - programmable
18. 24V relay output for AV - programmable
19. 24V relay output for AV - programmable
20. LED indicator board
21. Grounding point for lid
RELAY 4
24V 0V
RELAY 5
24V 0V

White White
Gnd
Gnd
Yellow Yellow
NO
NO
NO
1 2 3 4 5 6 7
Motor Connection
24V
24V
24V
24V
+
Brake Resistor Load Resistor
+ Battery - Connection + PSU - Connection
+ 24V Aux - 0V Output
L
L
Green Green
NC
NC
NC
0V
0V
0V
0V
-
H
H
Brown Brown
COM
COM
COM
Open
Emer. Retract
Com
Close
Com
Fire
Access
Alarm
Input 1
Alarm
Input 2
Alarm
Test
Stop
P1000 Motor Connection XL29/16, XL38/12 & XL60/8 ASB BS Motors Only
and AV Fuse Connections
BS Motors Require No External Stutter Brake
On XL60/8 ASB Motors - Connect 1 - 7 wires only
Open
Emer. Retract
Com
Close
Com
Fire
Access
Alarm
Input 2
Alarm
Input 1
Test
SC
Battery Fuse 7.5A
Automotive Blade
Aux Fuse 2A
OSE
Receiver
OSE
Transmitter
SELECT
Prg UP
Prg DOWN
Tubular Motor
5
2
6
1
4
3
7
RELAY 4
24V 0V
RELAY 5
24V 0V
RELAY 4
24V 0V
RELAY 5
24V 0V
500mA Fuses (none replaceable)

White White
Gnd
Gnd
Yellow Yellow
NO
NO
NO
1 2 3 4 5 6 7
Motor Connection
M7
P3
3
7
4
4
1
1
6
6
2
2
5
5
Motor Connection
24V
24V
24V
24V
+
Brake Resistor Load Resistor
+ Battery - Connection + PSU - Connection
+ 24V Aux - 0V Output
L
L
Green Green
NC
NC
NC
0V
0V
0V
0V
-
H
H
Brown Brown
COM
COM
COM
Open
Emer. Retract
Com
Close
Com
Fire
Access
Alarm
Input 1
Alarm
Input 2
Alarm
Test
Stop
P1000 Stutter Brake Module XL29/16 & XL38/12 ASB Motors Only
and AV Fuse Connections
IF BS MOTOR IS USED DO NOT FIT
Open
Emer. Retract
Com
Close
Com
Fire
Access
Alarm
Input 2
Alarm
Input 1
Test
SC
Battery Fuse 7.5A
Automotive Blade
Aux Fuse 2A
OSE
Receiver
OSE
Transmitter
SELECT
Prg UP
Prg DOWN
Tubular Motor
5
2
6
1
4
3
7
Stutter Brake Module
(as close to the motor as possible)
“P”-side of pcb “M”-side of pcb
RELAY 4
24V 0V
RELAY 5
24V 0V
RELAY 4
24V 0V
RELAY 5
24V 0V
500mA Fuses (none replaceable)

White White
Gnd
Gnd
Yellow Yellow
NO
NO
NO
1 2 3 4 5 6 7
Motor Connection
M7
P3
3
7
4
4
1
1
6
6
2
2
5
5
Motor Connection
24V
24V
24V
24V
+
Brake Resistor Load Resistor
+ Battery - Connection + PSU - Connection
+ 24V Aux - 0V Output
L
L
Green Green
NC
NC
NC
0V
0V
0V
0V
-
H
H
Brown Brown
COM
COM
COM
Open
Emer. Retract
Com
Close
Com
Fire
Access
Alarm
Input 1
Alarm
Input 2
Alarm
Test
Stop
P1000 Stutter Brake Module XL60/8G ASB Motor Only
and AV Fuse Connections
IF BS MOTOR IS USED DO NOT FIT
Open
Emer. Retract
Com
Close
Com
Fire
Access
Alarm
Input 2
Alarm
Input 1
Test
SC
Battery Fuse 7.5A
Automotive Blade
Aux Fuse 2A
OSE
Receiver
OSE
Transmitter
SELECT
Prg UP
Prg DOWN
Tubular Motor
5
2
6
1
4
3
7
Stutter Brake Module
(as close to the motor as possible)
“P”-side of pcb “M”-side of pcb
RELAY 4
24V 0V
RELAY 5
24V 0V
RELAY 4
24V 0V
RELAY 5
24V 0V
500mA Fuses (none replaceable)

White White
Gnd
Gnd
Yellow Yellow
NO
NO
NO
1 2 3 4 5 6 7
Motor Connection
24V
24V
+
Brake Resistor Load Resistor
+ Battery - Connection + PSU - Connection
+ 24V Aux - 0V Output
L
L
Green Green
NC
NC
NC
0V
0V
-
H
H
Brown Brown
COM
COM
COM
Open
Emer. Retract
Com
Close
Com
Com
Com
Com
Make
Make
Make
Break
Make
Break
Fire
Access
Alarm
Input 1
Alarm
Input 2
Alarm
Test
Stop
Alarm Override N/O
Momentary Operation
Key switch
Momentary
Operation
Firefighter Override N/O
Momentary Operation
Emergency
Emergency
P1000 Key Switch & Override
Connections
Open
Emer. Retract
Com
Close
Com
Fire
Access
Alarm
Input 2
Alarm
Input 1
Test
SC
Battery Fuse 7.5A
Automotive Blade
Aux Fuse 2A
OSE
Receiver
OSE
Transmitter
SELECT
Prg UP
Prg DOWN
Firefighter Access
15
Curtain Override
10
11
11
15
10
2200 ohm (2K2) Red-Red-Red Bands
1000 ohm (1K) Brown-Black-Red Bands
Important - Resistors must be fitted as per the drawings
If in doubt set multi-meter to setting and measure resistance
RELAY 4
24V 0V
RELAY 5
24V 0V

White White
Gnd
Gnd
Yellow Yellow
NO
NO
NO
1 2 3 4 5 6 7
Motor Connection
24V
24V
+
Load Resistor
+ Battery - Connection + PSU - Connection
+ 24V Aux - 0V Output
L
L
Green Green
NC
NC
NC
0V
0V
-
H
H
Brown Brown
COM
COM
COM
Com
Make
Break
Fire
Access
Alarm
Input 1
Alarm
Input 2
Alarm
Test
2200 ohm (2K2) Red-Red-Red Bands
1000 ohm (1K) Brown-Black-Red Bands
Important - Resistors must be fitted as per the drawings
Firefighter Override N/O
Momentary Operation
Emergency
P1000 Key Switch & Override
Connections
Fire
Access
Alarm
Input 2
Alarm
Input 1
Test
Battery Fuse 7.5A
Automotive Blade
Aux Fuse 2A
OSE
Receiver
OSE
Transmitter
SELECT
Prg UP
Prg DOWN
Firefighter Access
15
11
15
Brake Resistor
Open
Emer. Retract
Com
Close
Com
Com
Make
Make
Break
Make
Alarm Override N/O
Momentary Operation
Blue Wires - NC
Yellow Wires - NO
Key switch
Momentary
Operation
Emergency
Open
Emer. Retract
Com
Close
Com
SC
10
11
10
PRESS
TO EXIT
If in doubt set multi-meter to setting and measure resistance
RELAY 4
24V 0V
RELAY 5
24V 0V