Power Tec 70331 User manual

FOLLOW ALL STANDARD SHOP SAFETY
PRECAUTIONS, INCLUDING:
• Keep children and visitors at a safe distance from work area.
• Keep work area clean. Cluttered work areas invite accidents.
Work area should be properly lit.
• Do not use power tools in dangerous environments. Do not
use power tools in damp or wet locations. Do not expose
power tools to rain.
• TURN OFF AND UNPLUG all power tools BEFORE making
any adjustments or changing accessories.
• Be alert and think clearly. Never operate power tools when
tired, intoxicated or when taking medications that cause
drowsiness.
• Wear proper apparel. Do not wear loose clothing, gloves,
neckties, rings, bracelets or other jewelry which may get
caught in moving parts of the tool.
• Wear protective hair covering to contain long hair.
• Wear safety shoes with non‑slip soles.
• Wear safety glasses complying with United States ANSI
Z87.1. Everyday glasses have only impact resistant lenses.
They are NOT safety glasses.
• Wear face mask or dust mask if operation is dusty.
• A guard or any other part that is damaged should be properly
repaired or replaced. Do not perform makeshift repairs.
• Use safety equipment such as featherboards, push sticks and
push blocks, etc., when appropriate.
• Maintain proper footing at all times and do not overreach.
• Do not force woodworking tools.
CAUTION
Think safety! Safety is a combination of operator common
sense and alertness at all times when tool is being used.
WARNING
Do not use the Router Table Dust Collection System until it is
completely assembled and you have read and understood this
entire operating manual and the operating manual of the tool
being used with Router Table Dust Collection System.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE.
INSTRUCTION SHEET
Router Table Dust Collection System
WARNING
For your own safety, read all of the rules and precautions before
operating tool.
WARNING
Always follow proper operating procedures as dened in this
manual even if you are familiar with use of Router Table Dust
Collection System or any tool used with Router Table Dust
Collection System. Remember that being careless for even a
fraction of a second can result in severe personal injury.
Before using another tool with this product, always read,
understand and follow the instructions and safety warnings in
the owner’s manual for that tool. If you do not have the owner’s
manual, obtain one from the tool’s manufacturer before using it
with this product.
You must be familiar with the use of any tool or accessory used
with Router Table Dust Collection System. The supplier cannot
be held responsible for any accident, injury or damage incurred
while using Router Table Dust Collection System with any tool.
It is the responsibility of the purchaser of this product to ensure
that any person using this product reads and complies with all
instructions and safety precautions outlined in this manual and
the operating manual of the tool being used prior to use.
WARNING
Some dust created by operation of power tool contains
chemicals known to the State of California to cause cancer, birth
defects or other reproductive harm. To reduce your exposure
to these chemicals, work in a well ventilated area and work
with approved safety equipment. Always wear OSHA/NIOSH
approved, properly tting face mask or respirator when using
such tools.
CAUTION
Do not modify or use Router Table Dust Collection System for
any application other than that for which it was designed.
Model No. 70331
22‑1208

UNPACKING
Refer to Figure 1
NOTE: Check for shipping damage. Check immediately whether
all parts and accessories are included.
ITEM DESCRIPTION QTY
A Rubber Air Intake 1
BSecuring Strap 1
CFoam Strips (set of 4) 1
D2‑1/2" Y‑Fitting 1
E2‑1/2" Splice 1
FReducer 2‑1/2" to 1‑1/2" 2
GReducer 2‑1/4" to 1‑1/2" 1
H1‑1/2" Band Clamps 2
IEVA Hose 2‑ft 1
JEVA Hose 3‑ft 1
KSteel Hose Support Kit
(screw and washer attached) 1
ASSEMBLY NOTE: Reference Figure 2 as needed.
Figure 2

Figure 3
CAUTION Ensure Router is unplugged.
1. See Figure 4. Remove the router table main Resin insert
(with the router base attached) from the router table. Fasten
Air Intake (A) using Securing Strap (B). Carefully place two tabs
around one handle and press together hook & loop to secure.
Do the same for the other side pulling as tight as possible,
press to secure.
NOTE: For best results position router with lock-lever to front
away from rear discharge port of router.
Figure 4
2. See Figure 5. Feed 2‑ft. EVA Hose ( I ) through Hose Support
(K) and gently twist hose onto threads of Air Intake (A).
Figure 5
3. Place the main resin insert back into the router table and
secure following your router table instructions.
4. Attach Steel Hose Support (K) centering with the dust port.
Note: If attaching to a router table with metal tie bars, drill a 11/64"
hole and attach with included screw and nut. If attaching directly to
the edge of the table, an appropriate wood screw will be required.
5. See Figure 6. Using 2‑1/4"to 1‑1/2" Reducer (G) push it
into the dust port outlet on the router table. Attach 3‑ft EVA
Hose (J) to Reducer (G)
Figure 6
6. See Figure 7. Slip a 1‑1/2" Band Clamp (H) onto each hose
from router and router table, do not tighten at this time.
Insert Reducer 2‑1/2" to 1‑1/2" (F) into the end of each
hose. Now tighten the Band Clamps (H).
Figure 7
7. See Figure 8. Insert Reducers into 2‑1/2" Y‑Fitting (D). Next,
insert 2‑1/2" Splice (E) into base of 2‑1/2" Y‑Fitting (D).
Figure 8
Note: The kit, as
configured, connects to
a dust collection system
using a 2-1/2” ID flexible
dust collection hose. (This
hose and band clamp are
not included).

Southern Technologies, LLC
Chicago, IL 60606
Put these instructions and the original sales invoice
in a safe, dry place for future reference.
Visit us on the web at www.powertecproducts.com
WARNING
When servicing, use only identical replacement parts. Use of
any other parts may create a hazard or cause product damage.
To ensure safety and reliability, all repairs should be performed
by a qualied service technician.
WARNING
Keep the Router Table Dust Collection System dry, clean,
and free from oil and grease. Always use a clean cloth when
cleaning. Never use brake uids, gasoline, petroleum‑based
products or any strong solvent to clean the Router Table Dust
Collection System. Chemicals can damage, weaken or destroy
plastic which may result in serious personal injury.