MODEL P3500 CAT. NO.52000/Deluxe Kit 52001/Blister Pack
5P3500
K=Knurled TH=Top Hat
.300 HEAD DIAMETER DRIVE PINS WITH 3/4" WASHER
CAT. STD. STD. HEAD SHANK WT./
NO. SHANK ENGTH BOX CTN. DIA. DIA. 100
50070 3/4" 100 1000 .300 .143 1.6
50080 2-1/2" 100 1000 .300 .143 2.5
50082 3" 100 1000 .300 .143 2.8
.300 HEAD DIAMETER DRIVE PINS WITH 7/8" WASHER
CAT. STD. STD. HEAD SHANK WT./
NO. SHANK ENGTH BOX CTN. DIA. DIA. 100
50090 1" 100 1000 .300 .143 1.9
50092 1-1/4" 100 1000 .300 .143 2.0
50094 1-1/2" 100 1000 .300 .143 2.1
50096 2" 100 1000 .300 .143 2.4
50098 2-1/2" 100 1000 .300 .143 2.7
50100 3"* 100 1000 .300 .143 3.0
.300 HEAD DIAMETER DRIVE PINS WITH 1" WASHER
CAT. STD. STD. HEAD SHANK WT./
NO. SHANK ENGTH BOX CTN. DIA. DIA. 100
50108 1-1/4" 100 1000 .300 .143 2.2
50110 1-1/2" 100 1000 .300 .143 2.3
50112 2" 100 1000 .300 .143 2.6
50114 2-1/2" 100 1000 .300 .143 2.9
50116 3" 100 1000 .300 .143 3.2
.300 HEAD DIAMETER DRIVE PINS WITH 1-7/16" INSU ATION WASHER
CAT. STD. STD. HEAD SHANK WT./
NO. SHANK ENGTH BOX CTN. DIA. DIA. 100
50122 1-1/2" 100 1000 .300 .143 2.1
50126 2-1/2" 50 500 .300 .143 2.7
50132 3" 50 500 .300 .143 3.0
1/4"-20 THREADED STUDS
CAT. THREAD SHANK STD. STD. HEAD SHANK WT./
NO. ENGTH ENGTH BOX CTN. DIA. DIA. 100
50320 1/2" 1/2"K 100 5000 1/4" .143 .8
50322 3/4" 1/2"K 100 1000 1/4" .143 1.1
50326 3/4" 3/4" 100 1000 1/4" .143 1.2
50328 1/2" 1" 100 1000 1/4" .143 1.2
50330 3/4" 1" 100 1000 1/4" .143 1.4
50334 1/2" 1-1/4" 100 1000 1/4" .143 1.4
50336 3/4" 1-1/4" 100 1000 1/4" .143 1.5
50338 1-1/4" 1-1/4" 100 1000 1/4" .143 1.7
.300 HEAD DIAMETER PINS WITH CEI ING C IPS
CAT. SHANK STD. STD. HEAD SHANK WIRE WT./
NO. ENGTH BOX CTN. DIA. DIA. HO E 100
50363 1" 100 1000 .300 .143 0.278" 3.4
50364 1" 100 1000 .300 .143 0.278" 3.5
50368 1" 100 1000 .300 .143 0.278" 3.0
50370 1-1/4" 100 1000 .300 .143 0.278" 3.7
50374 1-1/4" 100 1000 .300 .143 0.278" 3.2
.300 DIAMETER HEAD DRIVE PINS WITH BX CAB E STRAPS AND CONDUIT C IPS
CAT. STD. STD. HEAD SHANK WT./
NO. DESCRIPTIONBOX CTN. DIA. DIA. 100
50150 1" 100 1000 .300 .143 3.5
50152 1-1/4" 100 1000 .300 .143 3.7
50380 1/2" EMT 1-1/4" pin 100 1000 .300 .143 3.4
50381 1/2" EMT 1" pin TH 100 1000 .300 .143 3.3
50382 1/2" EMT 1" pin 100 1000 .300 .143 3.3
50384 3/4" EMT 1-1/4"pin 100 1000 .300 .143 3.5
50385 3/4" EMT 1" pin TH 100 500 .300 .143 3.4
50386 3/4" EMT 1" pin 100 1000 .300 .143 3.3
50388 1" EMT 1" pin TH 25 250 .300 .143 3.2
.300 HEAD DIAMETER PIN WITH REBAR BASKET C IP
CAT. STD. STD. HEAD SHANK WT./
NO. DESCRIPTION BOX CTN. DIA. DIA. 100
50702 32mm w/ basket clip 100 100 8mm .143 4.0
50704 37mm w/ basket clip 100 100 8mm .143 4.1
50710 47mm w/ basket clip 100 1000 8mm .143 4.3
50712 52mm w/ basket clip 100 1000 8mm .143 4.4
50716 62mm w/ basket clip 100 1000 8mm .143 4.6
50718 72mm w/ basket clip 100 1000 8mm .143 4.8
FORMING PIN
CAT. STD. STD. HEAD SHANK WT./
NO. DESCRIPTION BOX CTN. DIA. DIA. 100
50790 62mm - 2-1/2" 100 1000 .205 .143 1.4
50789 44mm - 1-3/4" 100 1000 .205 .143 1.1
Saf ty Pr cautions
Safety is your primary responsibility when operating any
powder actuated tool. You must read and understand the
contents of this manual. You must be familiar with all functional
and safety requirements of the tool. It is your responsibility to
obtain proper training and a Powers Fasteners operator card prior
to using this tool in compliance with the current American
National Standard A10.3 Safety Requirements for Powder
Actuated Fastening Systems and the Federal Occupational Safety
and Health Administration Standards (OSHA). Existing state or
local regulations should also be followed. When using this tool,
you must have the qualified operators card in your possession.
Revocation of card - Failure to comply with any of the rules and
regulations for safe operation of powder actuated tools shall be
cause for the immediate revocation of your qualified operator card.
The following is a summary of safety precautions to be
followed when operating a Powers Fasteners powder actuated
tool. Failure to follow these safety instructions can result in
serious injury or death to operators or bystanders.
PRIOR TO OPERATING THE TOO
1. WARNING SIGNS SHOU D A WAYS BE POSTED
WITHIN THE AREA IN WHICH A POWDER ACTUATED
TOO IS TO BE USED. THESE SIGNS SHOU D BE AT
EAST 8" X 10" IN SIZE WITH BO DFACE TYPE THAT
IS NOT ESS THAN 1" IN HEIGHT. THE SIGN SHOU D
STATE "POWDER ACTUATED TOO IN USE".
2. Approved safety goggles should always be worn by operator
or bystander, to protect their eyes from flying particles. Hearing
protection should always be worn by the operator and
bystanders when using a powder actuated tool. Other personal
safety protection as required should also be used.
3. Never modify or fabricate parts for use in your Powers tool.
Use only Powers fasteners, loads, and tool parts.
4. Hands or other body parts must never be placed in front of
muzzle/barrel. Accidental discharge can cause piston and/or
fastener to pass through the operator’s hand.
5. Never compress the tool against any part of the body.
Serious injury or death may result in the event of an accidental
discharge.
6. Always point tool in a safe direction at all times.
7. Use the tool for its intended purpose only.
PREPARATION FOR OADING THE TOO
1. Tools must be checked prior to operating to make sure they
are not fully or partially loaded with a powder load or fastener.
2. To insure safe operation, perform the daily function test
described in this manual. Be sure the tool is not loaded prior to
performing this test.
3. Do not operate this tool unless all its parts are in place and
operating appropriately. Never attempt to use a malfunctioning
tool. Call 1-800-524-3244 for assistance.
4. Never guess about the suitability of a base material. If you
are uncertain about the suitability of a base material, perform a
center punch test.
5. Do not operate the tool until you learn and understand the
color code / numbering system used to identify the power level
of powder loads.
OPERATING THE TOO
1. Only use fasteners and powder loads designed for this tool
as supplied by Powers Fasteners.
2. Do not use powder actuated tools in a flammable or an
explosive atmosphere.
