Poynt 5 User manual

Quick Start Guide
1

Step 1: Set up your Poynt Web Portal account.
Open your welcome email and click “Get
Started” to create your login credentials.
Step 2: Log in at Poynt.net to view your
dashboard. Once your terminal arrives, this is
where you’ll be able to see your real-time
customer and transaction data.
Step 3: Visit the Poynt Help Center to review
helpful video tutorials and support articles.
Your Poynt 5 is on its
way!
2

Your Poynt 5 has
arrived!
Step 1: Check your box
Do a quick component check to ensure all
content is in the box. It should include:
❏ Poynt 5 Device
❏ Power cable
❏ Power Adapter
❏ Quick Start Guide
3

Poynt 5 Setup
Step 2: Charge your Device
Using the included power adaptor and USB
cable, plug in your Poynt 5 to charge.
The smaller end of the cable should be inserted
at the bottom of the device just underneath the
Home button. This is reversible so it doesn’t
matter how you spin it.
4

Poynt 5 Setup
Step 3: Power on your device
To power on your Poynt 5, slide down the
springed button on the right hand side of the
device toward the bottom of the device.
5

Poynt 5 Setup
Step 4: Placing the Device
The Poynt 5 device fits in the palm of your hand
so you have the freedom to transact wherever
your customers are.
6

Poynt 5 Setup
Step 5: Connect your device
Your device will walk you through connecting to
the internet via WiFi the first time you turn it on.
After connecting, it may begin to update its
software as required. This can take a few
minutes. Allow the device to download, install,
and reboot before getting started.
7

Poynt 5 Setup
Step 6: Access your Notification and Settings
To access Notifications on your device, as well
as adjust any settings, simply swipe down from
the top from anywhere on the device.
With one swipe, you’ll see a notifications tray.
With a secondary swipe you’ll be able to quickly
adjust brightness and volume and make
additional adjustments within Settings.
8

FCC
FCC ID: 2AFD7-P0501
Contains FCC ID: 2AFD7-P0502
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
oReorient or relocate the receiving antenna.
oIncrease the separationbetween the equipment and receiver.
oConnect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
oConsult the dealer or an experienced radio/TV technician for help.
FCC Caution
oAny changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
oThis transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.

The country code selection is for non-US model only and is not available to all US
model. Per FCC regulation, all WiFi product marketed in US must fixed to US
operation channels only.
Radiation Exposure Statement
This device meets the government’s requirements for exposure to radio waves. This
device is designed and manufactured not to exceed the emission limits for exposure
to radio frequency (RF) energy set by the Federal Communications Commission of
the U.S. Government.
Specific Absorption Rate (SAR) refers to the rate at which the body absorbs RF
energy. The SAR limit is 1.6 watts per kilogram in countries that set the limit averaged
over 1 gram of tissue and 2.0 watts per kilogram in countries that set the limit
averaged over 10 grams of tissue. During testing, Poynt 5 radios are set to their
highest transmission levels and placed in positions that simulate uses when worn or
carried against the torso of the body, with 5mm separation.
Cases with metal parts may change the RF performance of the device, including its
compliance with RF exposure guidelines, in a manner that has not been tested or
certified.
Although this device has been tested to determine SAR in each band of operation, not
all bands are available in all areas. Bands are dependent on your service provider’s
wireless and roaming networks.
IC
IC : 22579-P0501
Contains IC : 22579-P0502
Industry Canada statement