PR Lighting ARC LED 1572 User manual

1
ARC LED 1572
PR-6262
The user manual contains important information about the safe installation and use of a projector. Please read
andfollowtheseinstructions carefullyandkeepthe manualinasafe placeforfuturereference.
PR LIGHTING LTD.
http://www.pr-lighting.com

2
INDEX
1.
SAFETYANDWARNINGS ……………………………………………………………………………………………
4
2.
INSTRUCTIONS…………………………………………………………………………………………………………
5
3.
INSTALLATION……………………………………………………………………………………………………………
6
4.
SETUPANDCONFIGURATION…………………………………………………………………………………………
7
5.
OPERATIONMENU………………………………………………………………………………………………………
9
6.
DMXPROTOCOL…………………………………………………………………………………………………………
12
7.
SIGNSONTHELCD DISPLAY …………………………………………………………………………………………
13
8.
TECHNICALDATA ………………………………………………………………………………………………………
13
9.
COMPONENTORDER CODES …………………………………………………………………………………………
15
ACCESSORIES
The followingitemsaresuppliedwiththeprojectorand pleasecheck:
Name
Quantity
Unit
Remark
XLRcable
1
pc
Withplugandsocket
Safetycord
1
pc
User manual
1
pc
Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without notice.
Whilst every care is taken in the preparation of the manual we reserve the right to change specifications in the course of product
improvement.Thepublisherscannotbeheldresponsiblefortheaccuracyoftheinformationherein,oranyconsequencearisingfromthem.
Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good
conditionbeforeinstallationand use.Shouldthere be any damage causedby transportation, consultyourdealer and do not use theunit. Any
damagecausedbyimproperusewillnotbeassumedby themanufacturerand/ordealer.
Anyfuturetechnicalchangeintheusermanual won’t be with any further notice.
Note: Forthe productsmade by GuangzhouPR lighting Ltd, thewarrantyforthe wholeproduct is one yearstarting fromthe delivery date
butthelightsourceisnotwithinthewarranty.

3
1. SAFETYANDWARNINGS
NOTE
Before a projector’s installation, power-on, operation and maintenance, please carefully read
thesafetyinformationhereinafter!
Thefollowingsafetysignsareusedintheusermanual.
Warning
User
Manual
Electrical
shock
Goggles
Protective
Gloves
Flames
High
Temperature
● When unpacking, check if there is transportation damage before using a projector. Should there be any damage
causedbytransportation,consultyourdealerand do notuseit.
●The manufacturer is not responsible for any loss caused by the user not following the manual or changing a
projectorashe/shelikes.
●Please be noted that the damage caused by changing a projector at will is not warranted.
● Do not hesitate to contact the dealer orthe manufacturer ifany questionsor advice.
● A projector with IP67canbeusedindoorsand outdoors.
●A projector should be kept away from high temperature, fire, electrical surge, vibration and strong light while
running.
●Only qualified technicians can install ,operate and maintain a projector strictly as per the processes stipulated in
the manual.
●.Any maintenance and repair of a projector shouldn’t be carried out by a user and the user shouldn't open it for
anyrepair work.
●Don’t look straightly into the light sources especially for epileptics, otherwise eyes will be burned.
●Do not connectaprojectortoany typeofdimmerpack.
●Ifthe LEDlamps,lensand screen protectivecoveroftheaprojectorhave obviousdamage,i.e.,tothe extent
thatit hurtstheperformancelikecrackingordeformation.Please stopusingitand replacethemwith the original
parts,otherwiseitsperformancewillbecompromised.
● For the installation location of a projector, it shouldn’t be seenin the distance oflessthan4metersfor along
time.
●Before operation, please confirm that all covers (housing) are on and screws tightened. It’s forbidden to use a
projectorwhilecovers(housing)areoff.
●While operating it, wear protective itemslikeeye goggles, glovesandetc..
●Any electrical connection must be carried out by a qualified person .
●Beforeinstallation, pleaseconfirm thevoltage supplied matcheswhatisrequiredforaprojector.
●Each projector must be properly earthedand installed asperrelatedelectrical standards.
●Do not use power cord with its insulator damaged and connect the power cord with other cables.
●If aprojectoris not used or under cleaning,, please hold the plugand unplugit. Do not unplug it forcefullyor by
pullingthepowercable.

4
●All power cords must conform to related safety and regulations.
●Do not switch on and off a projector constantly in very short intervals, otherwise the light source’s and other
electrical parts’ life will be shortened .
●There are safety cord holes in either arm of a projector. In view of safety, please run the safety cord supplied
throughthe safetycord holesfor safetysupport.
●Beforeany installation, maintenanceandcleaning work,pleaseensureaprojectorisdisconnectedfrompower
mains.
● While running normally under normal ambient temperature, the temperature of the external surface of the metal
housingofaprojector(thesurfaceoftheheatsink)mayreach60℃.
●While it running, don’t touch the metal housingwith bare handsto avoid beingburned!
●Do not mount a projector directly on inflammable surface.
●Do notprojectthebeamstraightlyoncombustibleitems andthe minimum distancebetweenaprojector
andilluminateditems is10m.
●A projector should be installed with good ventilation and the minimum distance between a projector and a wall
is50cm.Atthesametime,pleaseensurethefansandair inlets and outletsareworkable.
2.INSTRUCTIONS
●CLEANINGANDMAINTENANCE
Under normal running, the protective units of a projector should be inspected regularly like power fuse. If it is burned, please
installanewoneandensure itisthesameratingastheburnedone.
For a projector with an over-temperature protective unit, please inspect cooling units regularly like cooling fans, heat sink and
othercoolingparts. Pleasecheckif the fansrunnormallyorfansandairinletsareblocked bydust.To keepairinlets/outletsclean,
coolingfansshouldbecleaned every15days.
For waterproof projectors, unless confirmed by a professional technician for the replacement of some internal components, it’s
forbiddentodismantleit. For theprojectors likethis,just keep themcleanif no fans forcooling.
Cleaning frequencyis to be decided byoperations and its environment. Use soft cloth and normaldetergent for glassfor cleaning
work. It’s advised external optical system be cleaned every 20days. For a projector with high IPrating, if no damage inside, it is
advised to cleanthe surfacesofitshousinginprinciple. Keep lens cleanand do not touchopticalpartswithbare hands.
SPECIALNOTE:
For waterproof projectors, it’s normal fortheirfrontlenstohavemildmistduringoperations.
●Before any maintenance and cleaning, please ensure a project is off the power.
●Only a qualified person is allowed to do maintenance.
●Do not usealcohol orother organicsolventto cleanthehousingto avoiddamage.
●Do not use any solvent with chemical elements to clean coated filters.

5
●TROUBLESHOOTING
PROBLEM
ACTION
The projector doesn’t switch on
Checkthefuseonthepowersocket.
ChecktheLEDlamps.
TheLED lampsare onbutthe projector doesn’t
respondto thecontroller
Makesurethattheprojector’s start address is right
Replaceor repair theXLRsignalcable.
Theprojector functions intermittently
Makesurethefanisworkingwellorfansandtheirshieldsarenotblocked
Beam appearsdim, Lowinbrightness
Make sure the LED lampsare withintheir lifespan
Removedustorgrease fromthelenses.
Theprojectimageappearsto havea halo
Carefullycleanoptical lensesand othercomponents.
HeavilyDefectiveBeam
Checkif lensarein goodcondition(notcracked)
Cleandustor greaseonthelens.
3. INSTALLATION
●POWERCONNECTION
Connectthepower cord as follows:
L(live)=brown
E(earth) =yellow/green
N(neutral)=blue
Before power connection, please ensure the power supplied must match what the nameplate says. It is recommended that each
projectorbe connected withpowerseparately so that theymaybeindividuallyswitchedonand off.
Note: If projectors are connected in series, please connect POWERIN port of the 1st projector with the Power Mains, then
connectitsPOWEROUT withPOWERIN of the2nd projector,and soontillallfixturesare connected.Ifthe voltagesupplied
is 200V-240V, the maximum projectors connected is 8pcs, if it is 100V-120V, the maximum is 4pcs. The diameter ofthe cores
ofthewiresforthePowerin/outcablesmustbeequalorbiggerthan2.5mm2
●Theearthwire(yellow/green) mustbe connectedto theground.And electricalconnectionmustbe in
accordancewiththe standardsconcerned.
●Ifany questionsaboutthe electricalinstallation,do not continuebut consulta qualifiedelectrician.
●DMXCONTROLCONNECTION:
Connection between controller and projector and between one projector and another must be made with a twin-screened cable, with
each wire having at least a 0.5mm in diameter. Connection to and from the projector is via cannon 5 pin (which are included with the
projector)or5pinXLRplugsandsockets.TheXLR'sareconnectedasshowninthefigureabove.
Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. XLR plugs and sockets
mustn’t be connected in any way other than mentioned in the above figure. The unit accepts digital control signals in protocol
DMX512(1990).
Connect the controller’s DMX output to the first fixture’s DMX input, and connect the first fixture’s DMX output to the second
fixture’s DMX input and connect the rest fixtures in the same way. Eventually connect the last fixture’s DMX output to a DMX
4N/C
N/C
5
PIN FUNCTION
GND
1
3 DATA+
DATA-
2
DMX 512
DMX 512
2DATA-
DATA+3
1GND
FUNCTION
PIN
五芯
三芯
DMX OUT DMX IN
DMX IN
DMX OUT
1
2
3
1
2
3
4
5
12
3
5
4
3
2
1

6
terminatorasshowninthefigurebelow.
●DMXTERMINATOR
In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents
electrical noisefromdisturbingandcorruptingtheDMXcontrolsignals.
The DMX terminator is simply an XLR connector with a 120(ohm) resistor connected across pins 2 and 3, which is then plugged
intotheoutput socketonthe last projectorin the chain.The connectionsare illustrated below.
4.SETUPANDCONFIGURATION
●FRONTPANELOPERATION
To setDMXaddressandfunctionssimplyandconveniently, usetouchkeysand LCDdisplay.
To browse through or modify the projector’s functions, press key ENTER for more than 3 seconds to unlock the control panel and
enter the menus. To set or browse through the projector’s functions, press key UP or DOWN. Press the key ENTER to enter the
submenus andthecurrentparameterswillbe displayedwhile flashing.Press key UP or DOWN tochange values(plusorminus)
Press key ENTER to saveyourchangesand enter into theupper levelmenu whileflashingsstop;
Press key FUNC,it willreturntotheuppermenu(parametersnotsaved)or browse through1st levelmenus;
IfDMXsignal is available,LEDindicationison. Otherwiseitisoff.
Terminator
Output Input
DMX512
Controller
Output Input
21
3
120
DMX TERMINATOR
CONNECTION
Connect a 120 (OHM) resistor
across pins 2 and 3 in an XLR plug
and insert into the DMX out socket
on the last unit in the chain. PIN 3
PIN 2

7
●DMXSTARTADDRESS
EachProjectormust be givenaDMXstartaddresssothatthe correctprojectorrespondstothe correctcontrol signals. ThisDMXstart
address is the channel number from which the projector starts to “listen” to the digital control information being sent out from the
controller. The Unit has 3 DMX modes. There are short mode, standard mode and extended mode. For example standard mode has
XX channels, so set the No. 1 projector’s address XXX, No. 2 projector’s address XXX, No. 3 projector’s address XXX, No. 4
projector’s address XXXandso on.
Launch the projector. Pressbutton ENTER more than2secondsto unlock panel.
Pressbutton ENTER to displayDMXaddress;
Pressbutton UP and DOWN,youcanset theaddress;
Pressbutton ENTER to confirm;afterpoweredonnext time,the defaultwillbelastvalue saved
Pressbutton FUNC,itwillreturntothe uppermenu
●STAND-ALONEMODE
Operate the projector without connecting with a controller, enable the master mode through the operation panel, the
projector will run in Stand-Alone mode automatically.
DMX address can be set at any number within 512.
●MASTER/SLAVEMODE
Many projectors can run synchronously in the Master/Slave mode by linking them with each other. First,
connect the first fixture’s DMX output to the second fixture’s DMX input using XLR-XLR control cable and then connect the second
fixture’s DMX output to the third fixture’s DMX input, and so on until all projector are connected in this way. Eventually connect the
last fixture’s DMX output to a DMX terminator. Set 1st projector as the master and others are Slaves.
Start AddressesofallSlavesare001;Operation mode of the Master can be set any mode for a Master’ and Slaves’ operation mode can
be setaccordingly
AfterPowered on,thegroup willrun inMaster/Slave Mode
5. OPERATIONMENU
1st level menu
2ndlevelmenu
3rdlevelmenu
4thlevelmenu
5thlevel
menu
DMX
Address
001 -XXX
Config
ChannelMode/
(Note: different
RGBA,
RGBW,
5CHShort/5CH
7CHStandard/7CH
Master Slave Slave
Terminator
Output Input Output Input

8
colormodewith
different menus)
RBGL
11CH Extended
/11CH
RGB
4CHShort/4CH
6CHStandard/6CH
10CH Extended
/10CH
WA
3CHShort/3CH
5CHStandard/5CH
6CHExtended/6CH
W
1CHShort/1CH
2CHStandard/2CH
3CHExtended/3CH
MasterSlave
Slave
Master
Loss ofDMX
Off
On
Hold
GammaCurve
2.0
2.2
2.4
2.6
LedRefreshRate/
1200Hz
2400Hz
4800Hz
10000Hz
12000Hz
15000Hz
Dimmer Speed
Fast
Medium
Slow
Color Offset
(Note: different
colormodewith
different menus)
RGBA,
RGBW,
RBGL
Red
90-128
Green
Blue
Amber(White,Lime)
RGB
Red
90-128
Green
Blue
WA
White
90-128
Amber
W
White
90-128
PRMTransmit
Cancel
OK

9
Defaults
Cancel
OK
Factory
0-1000
Display
Language
English
Chinese
Mode
OffAfterDelay
On Always
Invert
Off
On
Information
TemperatureLED/
xx.x C
Ampere(Note：
Someprojectorsdo
nothavethemenu)
x.xx A
Voltage
xx.x V
Fan(Note：Some
projectorsdonot
havethe menu)
Stop
Run
Error
ChannelValue
…
Dimmer:0-255
…
LEDType
W/WA/RGB/RGBW/RGBA/RG
BL…
TotalHours
hhhhhhhh:mm
Software Ver
x.x.x
ElectronicSN
xxxxxxxxxxxx
RDM
Ver
ANSIE1.20
DeviceLab
XXXXXXXX
TestMode
Self Test
Cancel
OK
Manual Test(Note:
different color
mode withdifferent
menusandsome
projectorsdonot
havefan menu)
RGBW
RGBA
RGBL
Red
Green
Blue
Amber(White,Lime)
RGB
Red
Green
Blue
WA
White
Amber

10
W
White
Fan
Fan
RunMode
DMX
Cancel
OK
PresetMemory
PR1
PR2
…
PR16
UserMemory
Cancel
OK
EditMemory
StaticScen1 (Note:different
colors withdifferent menus)
Dimmer
0-255
Strobe
0-255
RG
BW
RG
BA
RG
BL
Red
0-255
Green
Blue
Amber(White,Lime)
RG
B
Red
0-255
Green
Blue
WA
White
0-255
Amber
W
White
0-255
FadeTime
0．0-25．0s
HoldTime
0．0-25．0s
StaticScen2
…
…
StaticScen16
ResetMemory
Cancel
OK

11
6. DMXPROTOCOL
DMX512 channel mode(RGBA/RGBW/RGBL)
Shortmode
Standard
mode
Extended
mode
1
1
1
Red
0-255
2
2
2
Green
0-255
3
3
3
Blue
0-255
4
4
4
Amber(White,Lime)
0-255
5
5
5
Dimmer
0-255
6
Dimmer L(16bit)
0-255
6
7
Strobe
6-255
7
8
CCT(colortemperature)
1-255
9
Hue
1-255
10
Saturation
1-255
11
Macro
3-255
DMX512channelmode (RGB)
Shortmode
Standard
mode
Extended
mode
1
1
1
Red
0-255
2
2
2
Green
0-255
3
3
3
Blue
0-255
4
4
4
Dimmer
0-255
5
DimmerL(16bit)
0-255
5
6
Strobe
6-255
6
7
CCT(colortemperature)
1-255
8
Hue
1-255
9
Saturation
1-255
10
Macro
3-255
DMX512 channel mode(WA)
Shortmode
Standard mode
Extended
mode
1
1
1
Amber
0-255
2
2
2
White
0-255

12
3
3
3
Dimmer
0-255
4
DimmerL(16bit)
0-255
4
5
Strobe
6-255
5
6
CCT(color temperature)
1-255
7
Hue
1-255
8
Saturation
1-255
9
Macro
3-255
DMX512 channel mode(W)
Shortmode
Standard
mode
Extended
mode
1
1
1
Dimmer
0-255
2
DimmerL(16bit)
0-255
2
3
Strobe
6-255
7. SIGNSONTHELCDDISPLAY
8. TECHNICALDATA
ELECTRIC SPECIFICATIONS
Inputvoltage:100V~240VAC，50/60Hz
Inputpower:1000W@220V
Powerfactor:PF＞0.9
LIGHTSOURCESPECIFICATIONS
PhilipLED lamp RGBW4in1,SMT,15W
ManufacturersRatedLamp Life 50000hours
STROBE/DIMMER
Electronic Strobe0.3-25FP.S(Built-inpulsestrobeeffects)
MOVEMENT
DMX
signalindication
Don
DMX signalOK
Dflashing
NoDMXsignal
S on
Slavemode
SD
DMXoperationmode
SP
Preset memory
SU
User memory
SS
Staticscene1-16
Mon
Master mode
MD
DMXoperationmode
MP
Preset memory
MU
User memory
MS
Staticscene1-16

13
180°verticaldirection,manualadjustment
BEAMANGLE
CONTROL
International standardDMX512 signaland5-pinDMX512interface
The number ofDMX controlchannelsvariesbasedondifferentcolor mode
There areshort mode, standard modeandextended mode
OTHER FUNCTIONS
Fixtureandlamp hoursdisplayed
Modularstructureforeasymaintenance
DMX512 wirelessreceiver
OptionalDMX512 wirelesstransmitter
HOUSING
HightensilecastAluminumalloy, IP67
WEIGHT
Netweight46Kg
Grossweight53Kg
OPERATIONTEMPERATURE
Maximumambienttemperature:40 ℃
LIGHTOUTPUT
DISTANCE (m) 0 2.5 5 7.5 10 12.5 15
DIAMETER (m)
2.33 4.66 6.99 9.33 11.66 13.99
0
44286 11072 4921 2768 1771 12300
lux
Beamangle 14° （1/2θ）
Fieldangle 37°X57° （1/10θ）

14
SIZES
BASEINSTALLATION
9.COMPONENTORDERCODES
NAME
CODENUMBER
QTY
REMARKS
SWITCHINGPOWERSUPPLY
192010215
2
MAIN BOARD
230061490
1
LEDLAMPBOARD
230061488
8
HEATCONDUCTINGPAD
6290000019A
8
FAN
30069005
2

15

16
PR LIGHTING LTD.
1582 XingyeAvenue,NancunPanyu
Guangzhou, 511442 China
TEL:[phone]
PR lighting will try its best to offer accurate and overall information about a product’s technical data. Any changes won’t be notified if necessary. Patented Products.
CounterfeitingWillbeProsecuted! P/N: 6320000097A
Version: 20201102