PR Lighting XRLED 2500-WFraming User manual

1
XRLED 2500-W Framing
PR-8157
This product manual contains important information about the safe installation and use of this projector.
Please read and follow these instructions carefully and keep this manual in a safe place for future reference.
PR LIGHTING LTD.
http://www.pr-lighting.com

2
INDEX
1. SAFETYAND WARNINGS……………………………………………………………………………………
2. INSTRUCTIONS………………………………………………………………………………………………
3.APPEARANCE…………………………………………………………………………………………………
4.INSTALLATION…………………………………………………………………………………………………
5. SETUPAND CONFIGURATION ………………………………………………………………………………
6.OPERATION MENU ……………………………………………………………………………………………
7. DMX PROTOCOL………………………………………………………………………………………………
8.SIGNS ON THE TOUCH SCREEN ……………………………………………………………………………
9.ERROR MESSAGES ……………………………………………………………………………………………
10.TECHNICAL DATA ……………………………………………………………………………………………
11.CIRCUIT DIAGRAM …………………………………………………………………………………………
12.COMPONENT ORDER CODES………………………………………………………………………………
3
4
5
6
8
10
15
24
24
25
29
31
The following items are supplied with the projector and please check:
Name
Quantity
Unit
Remark
G clamp
2
Pcs
XLR connector
1
Set
Male and female
Safety cord
2
Pcs
User manual
0
Pc
QR Code
Ω clamp
2
Pcs
Optional
Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change
without notice. Whilst every care is taken in the preparation of the manual we reserve the right to change specifications in the
course of product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any
consequence arising from them.
Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are
in good condition before installation and use. Should there be any damage caused by transportation, consult your dealer and
do not use the unit. Any damage caused by improper use will not be assumed by the manufacturer and / or dealer.
Any future technical changes are not subject to further notice.
Note: For the products made by Guangzhou PR lighting Ltd, the warranty for the whole product is one year starting from
the delivery date but the light source is not within the warranty.

3
1. SAFETYAND WARNINGS
NOTE
Before a projector’s installation, power-on, operation and maintenance, please carefully read
the safety information hereinafter!
The following safety signs are used in the user manual.
Warning
User
Manual
Electrical
shock
Goggles
Protective
Gloves
Flames
High
Temperature
● When unpacking , check if there is transportation damage before using the projector. Should there be any
damage caused by transportation, consult your dealer and do not use it.
●The manufacture is not responsible for loss caused by the user not following the manual or changing the
projector as he/she likes.
●Please be noted that the damage caused by changing the projector at will is not warranted.
● Do not hesitate to contact the dealer or the manufacturer if any questions or advice.
● The projector is for indoor use only, IP20.
● Use only in dry locations. Keep this unit away from rain and moisture, excessive heat, humidity and dust. Do
not allow contact with water or any other liquids.
●The projector should be kept away from high temperature, fire, electrical surge, vibration and strong light while
being operated.
●The projector is only intended for installation, operation and maintenance by qualified personnel. And the
operation must strictly follow the procedures in the manual.
●The projector is not for a user for any replacements and the user shouldn't open the projector for repair and
maintenance.
●Don’t look straightly into the light sources especially for epileptics, otherwise eyes will be burned..
●Do not connect this device to any type of dimmer pack.
●If the lamp, lens and screen protective cover of the a lighting fixture have obvious damage, i.e., to the extent
that it hurts the performance like cracking or deformation. Please stop use it and replace them with the original
parts, otherwise its performance will be compromised.
● For the location of a lighting fixture, it shouldn’t be seen in the distance of less than 4 meters.
●Before operation, please confirm that all covers(housing) are on and screws tightened. It’s forbidden to use a
projector while covers(housing)are off .
●Keep the lamp clean and do not touch it with bare hands.
●While operating it, wear protective items.
●Any electrical connection must be carried out by a qualified person .
●Before installation, please confirm the voltage supplied matches what is required for the projector.
●Each projector must be properly earthed and installed as per related electrical standards.
●Do not use power cord with its insulator damaged and connect the power cord with other cables.
●If the projector is not used or under cleaning,, please hold the plug and unplug it. Do not unplug it forcefully or
by pulling the power cable.
●All power cords must conform to related safety and regulations.

4
●While being operated, the projector should not be under rains or in humidity.
●Do not switch on and off the projector constantly in very short intervals, otherwise the light source’s and other
electrical parts’ life will be shortened .
●There are safety cord holes at the bottom of the base of a projector. In view of safety, please run the safety cord
supplied through the safety cord holes for safety support.
●Before any installation, maintenance and cleaning work, please ensure the projector is disconnected from
power mains.
●.After stable operation under normal ambient temperature ,the temperature of the external surface of the
housing of the LED lighting fixture (the surface of the heat sink) is 65℃at maximum after the stable running.
●.While the lamp is stricken for the first time, there will be smoke and strange smell. It’s normal and does not
mean the projector has some defects.
●While a lighting fixture works properly under normal ambient temperature, the maximum temperature of the
external surface of the control device (The integrated control device means the external surface of the housing of
the lighting fixtures electric chamber)allowed is 65 Celsius degrees.
●Do not mount the projector directly on inflammable surface.
●Do not project the beam straightly on combustible items and the minimum distance between the projector
and illuminated items is 10m.
●A projector should be installed with good ventilation and the minimum distance between the projector and
walls is 50cm.At the same time, please ensure the fans and air inlets and outlets are workable.
●The product meets The General Technical Requirements and Standards for Recycle and Use Of
ExpiredAppliance and Electronic Products.
●When the product meets disposal standards and needs to be disposed, a client needs to dispose and recycle it.
2. INSTRUCTIONS
●CLEANINGAND MAINTENANCE
If a projector can’t start. Please check if the fuse is blown up. If it does, replace it with a new fuse with same ratings. And the
projector has over-temperature protective device. If the temperature is too high, the protective device will be triggered to shut the
projector off. When it happens, please check if the fans run normally or fan shield is blocked by dust. After the issue is solved,
restart the projector.
The accumulation of oil, smoke and dust on the lens will compromise the light output and cooling efficiency. Cleaning a
projector is very necessary to ensure a reliable use of it. Cooling fans need to be cleaned every 15 days. Internal lens, reflector and
hot mirror need to be cleaned periodically to optimize light output. Use plastic\rubber fiber and fur (non-metallic) tools for
cleaning.And the tools can’t scratch or deform the heat sink.
Cleaning frequency is to be decided by operations and its environment. Use soft cloth and normal detergent for glass for cleaning
work. It’s advised external optical system be cleaned every 20days and internal optical systems every 30/60days. Keep lens clean
and do not touch optical parts with bare hands.
●Before any maintenance and cleaning, please ensure the projector is off the power.
●Only qualified person is allowed to do maintenance.
●During maintenance and before maintenance, the projector must be off power.

5
●To avoid sunlight or other light penetrating into the head via the front lens, resulting in high temperature internally
causing damages to the projector. Before power-off, please use Tilt channel to move the head and make it facing
downward.
● Do not use alcohol or other organic solvent to clean the housing to avoid damage.
●Do not use any solvent with chemical elements to clean color filters or hot mirror.
●LUBRICATION
To ensure smooth movement of gobos and zoom and focus lens, it’s advised rotators’ bearings and 2 sliding bars for zoom and
focus lens be lubricated every 2 months. High quality and high temperature lubricant/grease is advised..
●TROUBLESHOOTING
PROBLEM
ACTION
The projector can’t be switched on
Check if the fuse is burned
Check if the power cord is connected well
Check if the switching power supply is bad or not connected well. A
professional technician is required for the repair
Check if the control board is connected well. .A professional technician
is required for the repair
The projector can be switched on , but the LED
lamp’s brightness can’t be controlled
Check if the LED driver board is connected well. A professional
technician is required for the repair
The projector can be switched on normally, but
not controlled by the DMX controller
Make sure that the fixture’s start address is right
Replace or repair the XLR signal cable.
The beam is not bright and its brightness
decreases sharply
Make sure the fans are working well or fans and their shields are not blocked
bydust.
Makesure that the internal opticsisclean.
The project image appears to have a halo
Carefully clean the LED lamp, optical lenses and other components.
Heavily Defective Beam
Check if lens are in good condition(not cracked)
Clean dust or grease on the lens.
3. APPEARANCE
BASE
ARM
HEAD

6
4. INSTALLATION
●RIGGING
During transportation, please lock the projector well; Before the use of projector please unlock the head. It’s forbidden to run the
projector without unlock Pan and Tilt
Take 2 clamps and 1 safety cords out from the package and mount 2 clamps on the underside of fixture with 4 retainers attached to
each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the WARNING on the underside of
the base as shown above) Always ensure that the projector is firmly anchored to avoid vibration and slipping whilst functioning.
Always ensure that the structure that you are going to mount the projector is secure and is strong enough to support the weight of the
fixture.
WARNING:
●The projector MUST be lifted or carried by the HANDLES instead of clamps.
●.For safety the safety cord should afford 10 times the Projector’s weight.
●.For safety, it should not be hung by its sides.
CLAMP
SAFETY
CORD
WARMING
Please run safety cord through
the safety hole circled in the
diagram for safety
Note：
1. Distance between feet and top of the
head
2. Distance between mounting bar and
top of the head
3. Fixture rotating diameter（minimum
spacing between fixtures）

7
●POWER CONNECTIONS
Connect the power cord as follows:
L (live) =brown
E (earth) =yellow/green
N (neutral) =blue
Before power connection, please ensure the power supplied must match what the nameplate says. It is recommended that each
projector be connected with power separately so that they may be individually switched on and off.
●The earth wire(yellow/green) must be connected to the ground. And electrical connection must be in
accordance with the standards concerned.
●If any questions about the electrical installation, do not continue but consult a qualified electrician.
●The lighting fixture is with waterproof power socket, it should be equipped with same IP rating power
plug.
●DMX CONTROLCONNECTION
Connection between controller and projector and between one projector and another must be made with a twin-screened cable, with
each wire having at least a 0.5mm in diameter. Connection to and from the projector is via cannon 5 pin (which are included with the
projector) or 5 pin XLR plugs and sockets. The XLR's are connected as shown in the figure above.
Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. XLR plugs and sockets
mustn’t be connected in any way other than mentioned in the above figure. The projector accepts digital control signals in protocol
DMX512 (1990).
Connect the controller’s DMX output to the first fixture’s DMX input, and connect the first fixture’s DMX output to the second
fixture’s DMX input and connect the rest fixtures in the same way. Eventually connect the last fixture’s DMX output to a DMX
terminator as shown in the figure below.

8
●DMX TERMINATOR
In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents
electrical noise from disturbing and corrupting the DMX control signals.
The DMX terminator is simply an XLR connector with a 120(ohm) resistor connected across pins 2 and 3, which is then plugged
into the output socket on the last projector in the chain.The connections areillustrated below
21
3
120
DMX TERMINATOR
CONNECTION
Connect a 120 (OHM) resistor
across pins 2 and 3 in an XLR plug
and insert into the DMX out socket
on the last unit in the chain.
PIN 3
PIN 2
5. SETUPAND CONFIGURATION
●FRONT PANELOPERATION
The configuration and start address can be set conveniently via push button and color touch screen.
To view or change its setup, touch any white area of the screen or push the key OK for more than 3 seconds to unlock the
display(While only on battery, push OK key). After the unlocking, push ► key to enter into function menus. Each main menu has its
submenus and each submenu has a specific function. For details, please see the “OPERATION MENU” with following
the 6th point..
1. In the page of function setup, push any key of ◄, ►, ▲ and ▼ or icon for the function desired.
2. At 2nd ,3rd and 4th level menus, key ◄ means ESCAPE, key ► won’t function, key OK means ENTER. Push key OK to
save any changes o enter into submenus. Push key ▲or ▼ to change numbers(plus or minus) or tap any item required
for changes.
Push the left key or shortcut key X to go back to the upper level menu. If none pushed, the system will go back to initial display
automatically.
Shortcut keys: after the interface of FUNCTION MENU, the upper part is with menus for many functions. On the right, there are 4
shortcut keys, which are ←,→,lamp control or English/Chinese menus.
●DMX STARTADDRESS
Each projector must be given a DMX start address so that the correct projector responds to the correct control signals.This DMX start
address is the channel number from which the projector starts to “listen” to the digital control information being sent out from the
controller. The projector has 3 DMX modes. There are short mode ,standard mode and extended mode. For example standard mode
has 42 channels, so set the No. 1 projector’s address 001, No. 2 projector’s address 043, No. 3 projector’s address 085, No. 4
projector’s address107, and so on.

9
Launch the projector. Press key OK more than 3seconds to unlock the display. After the unlocking, push key ► to enter into menus.
After selecting the sign of DMX setting, push OK key or tap the screen directly and select DMX address at 2nd level menus.
Push key▲ or▼ or tap sign < or > to set the number desired.
Push OK key to confirm.
Push key◄ and it will return to the upper menu
.
The projector has wireless control function with wireless receiver module and antenna for remote control.
The setup of it is below:
1. Enter into the projector’s menu. Select the menu “Config Settigns” via the keys of ▲ and ▼
2. Select DMX control Mode---- Wireless First (Note: Do not select XLR ONLY). The DMX wireless control
function is activated.
Only after the projector is linked with a transmitter, can it receive wireless signal sent by the transmitter. If unlinking it, Press
“Enter” for the menu of Unlink Wireless under the upper level menu of Config Settigns.
●STAND-ALONE MODE
Operate the projector without connecting with a controller, enable the master mode through the operation panel, the
projector will run in Stand-Alone mode automatically.
DMX address can be set at any number within 512.
●MASTER/SLAVE MODE
Many projectors can run synchronously in the Master/Slave mode by linking them with each other. First,
connect the first fixture’s DMX output to the second fixture’s DMX input using XLR-XLR control cable and then connect the second
fixture’s DMX output to the third fixture’s DMX input, and so on until all projector are connected in this way. Eventually connect the
last fixture’s DMX output to a DMX terminator. Set 1st projector as the master and others are Slaves.
StartAddresses of all Slaves are 001; Operation mode of the Master can be set any mode for a Master’and Slaves’operation mode can
be set accordingly.
After Powered on, the group will run in Master/Slave Mode

10
6. OPERATION MENU
1st
LEVEL
2nd LEVEL
3rd LEVEL
4th LEVEL
5th LEVEL
Address
DMX Address
1-475（ Short Mode）
1-471（Standard Mode）
1-456（ Extended Mode）
IP Address
Default IPAddress
2.X.X.X /10.X.X.X
Custom IPAddress
X.X.X.X
SubNet Mask
X.X.X.X
ArtNet
ArtNet Universe
0-255
sACN Universe
1-63999
Reset
Total Reset
Really Reset?
Confirm/ Cancel
Pan&Tilt Reset
Really Reset?
Confirm/ Cancel
Colour System Reset
Really Reset?
Confirm/ Cancel
Gobo Reset
Really Reset?
Confirm/ Cancel
Zo.Fo.Fr.Pr. Reset
Really Reset?
Confirm/ Cancel
Other Reset
Really Reset?
Confirm/ Cancel
Config
Settings
DMX Channel Mode
Short Mode 38CH
Standard Mode 42CH
Extended Mode 57CH
View Selected Mode
Strobe
…..
Signal Select
XLR Only
XLR First
Wireless Only
Wireless First
Wireless In/XLR Out
Artnet Only
Artnet In/XLR Out
sACN Only
sACN In/XLR Out
Loss of DMX
Normal time out
Hold last Value
Display Config
Display Mode
Off After Delay
OnAlways
Display Invert
Invert OFF
Invert ON
InvertAuto
Language Setting
English
Chinese
Touch screen calibration
XXX
Temperature Unit
Celsius Degree
Fahrenheit Degree
Un-Link Wireless
Really Un-Link?
Confirm/ Cancel
Defaults
Restore Defaults?
Confirm/ Cancel
Option
Settings
Pan/Tilt Settings
Pan DMX Invert
OFF/ ON
Tilt DMX Invert
OFF/ ON
Pan Tilt Swap
OFF/ ON
XYFeedback
OFF/ ON
Pan/Tilt mode
Speed/Time
Invert Settings
Iris Invert
OFF/ ON
Zoom Invert
OFF/ ON
CMYInvert
OFF/ ON
CTO Invert
OFF/ ON