PRASTEL MT4000-2 User manual

WARNING! Before installing, thoroughly read this manual that is an integral part of this
Kit.
N.B. - Prastel S.p.A. declines any responsibility in the event current standards in the country of
installation are not complied with
The symbol CE indicates conformity with Applicable European Directives
MT4000-2
ACCESS CONTROL UNIT
2 DOORS, 4000 USERS
MT10000-4
ACCESS CONTROL UNIT
4 DOORS, 10000 USERS

MT4000-2 MT10000-4 ISMTUK_06_06.doc
Pag. 2
1. Main Features: ___________________________________________________________________3
2. Terminal strip board and connectors_____________________________________________________4
3. Wiring _________________________________________________________________________8
3.1. Installation example with electric lock________________________________________________10
3.2. Installation example with automatic door_____________________________________________11
3.3. Example of connection between two control units ______________________________________12
4. Management of Alarm Events ________________________________________________________13
4.1. Example of installation with management of alarm events _______________________________14
5. Control Unit programming and testing __________________________________________________16
5.1. Creating the site __________________________________________________________________16
5.2. Searching for and configuring the terminal ___________________________________________17
5.3. Auto-learn of badges and assignment of authorisations__________________________________18
6. Control Unit Firmware Upgrading _____________________________________________________21
7. FAQ _________________________________________________________________________22

MT4000-2 MT10000-4 ISMTUK_06_06.doc
Pag. 3
1. Main Features:
MT4000-2
•Power: 12 VAC/DC
•Consumption: 100 mA (Control Unit without accessories). With the optional
keypad/display, consumption is 200mA
•Operating temperature: from -5 to +55°C
•Readers: 2 external readers
•User capacity: 4000
•Event record: 2000
•Time slots: 16 (4 time intervals for each time slot)
•Holidays: 20
•Relay outputs: 2 main (5A) and 2 auxiliary (1A)
•Digital inputs: 4 (2 configurable as break-in inputs)
•Antipassback: control unit and user configurable
•User identification: badge or badge + PIN code from keyboard (with keypad/display kit)
MT10000-4
•Power: 12 VAC/DC
•Consumption: 100 mA (Control Unit without accessories).With the optional
keypad/display, consumption is 200mA
•Operating temperature: from -5 to +55°C
•Readers: 4 external readers
•User capacity: 10000
•Event record: 16000
•Time slots: 16 (4 time intervals for each time slot)
•Holidays: 20
•Relay outputs: 4 main (5A) and 4 auxiliary (1A)
•Digital inputs: 8 (4 configurable as break-in inputs)
•Antipassback: control unit and user configurable
•User identification: badge or badge + PIN code from keyboard (with keypad/display kit)

MT4000-2 MT10000-4 ISMTUK_06_06.doc
Pag. 4
2. Terminal strip board and connectors
MT4000-2 Layout

MT4000-2 MT10000-4 ISMTUK_06_06.doc
Pag. 5
RESET: Re-start the control unit
BUZZER: 1 prolonged beep Ævalid reading
2 rapid beeps Æinvalid reading
Led OK: Green Ævalid reading
RedÆinvalid reading
YellowÆinvalid reading because of incorrect system code
Led TX/RX: Flashes when the control unit communicates on the RS485 bus.
Led ON/OFF: Red Æcontrol unit powered.
BATTERY: Back-up battery for keeping enablings in memory when the control unit is not
powered (life-span 3 years with control unit not powered).
DISPLAY STRIP: Strip for plugging in optional display.
KEYBOARD STRIP: Strip for plugging in optional keypad.
LCD: Trimmer for contrast adjustment of optional display
Terminal board MT4000-2 description
V1 Power 12Vac/dc (maximum consumption 2A)
V2 Power 12Vac/dc (maximum consumption 2A)
GND Ground for reader powering and for the INT485C converter
D+ D+ Interface 485
D- D- Interface 485
+9V Positive for reader powering and for the INT485C converter
D0.1 Reader 1 DATA0 line
D1.1 Reader 1 DATA1 line
D0.2 Reader 2 DATA0 line
D1.2 Reader 2 DATA1 line
IN1 Port 1 Output Pushbutton Input (active with voltage +9V)
IN2 Port 2 Output Pushbutton Input (active with voltage +9V)
IN5 Port 1 Break-in Input active with voltage of +9V
IN6 Port 2 Break-in Input active with voltage of +9V
NO1 Relay 1 N.O. contact
COM1 Relay 1 common
NC1 Relay 1 N.C. contact
NO2 Relay 2 N.O. contact
COM2 Relay 2 common
NC2 Relay 2 N.C. contact
NO5 Relay 5 N.O. contact
COM5 Relay 5 common
NC5 Relay 5 N.C. contact
NO6 Relay 6 N.O. contact
COM6 Relay 6 common
NC6 Relay 6 N.C. contact
Connector DB9 RS232 connector for printer or firmware upgrade from PC

MT4000-2 MT10000-4 ISMTUK_06_06.doc
Pag. 6
MT10000-4 Layout
RESET: Re-start the control unit
BUZZER: 1 prolonged beep Ævalid reading
2 rapid beeps Æinvalid reading
Led OK: Green Ævalid reading
RedÆinvalid reading
YellowÆinvalid reading because of incorrect system code
Led TX/RX: Flashes when the control unit communicates on the RS485 bus.
Led ON/OFF: Red Æcontrol unit powered.
BATTERY: Back-up battery for keeping enablings in memory when the control unit is not
powered (life-span 3 years with control unit not powered).
DISPLAY STRIP: Strip for plugging in optional display.
KEYBOARD STRIP: Strip for plugging in optional keypad.
LCD: Trimmer for contrast adjustment of optional display

MT4000-2 MT10000-4 ISMTUK_06_06.doc
Pag. 7
Terminal board MT10000-4 description
V1 Power 12Vac/dc (maximum consumption 2A)
V2 Power 12Vac/dc (maximum consumption 2A)
GND Ground for reader powering and for the INT485C converter
D+ D+ Interface INT485C
D- D- Interface INT485C
+9V Positive for reader powering and for the INT485B converter
D0.1 Reader 1 DATA0 line
D1.1 Reader 1 DATA1 line
D0.2 Reader 2 DATA0 line
D1.2 Reader 2 DATA1 line
D0.3 Reader 3 DATA0 line
D1.3 Reader 3 DATA1 line
D0.4 Reader 4 DATA0 line
D1.4 Reader 4 DATA1 line
IN1 Port 1 Output Pushbutton Input (active with voltage +9V)
IN2 Port 2 Output Pushbutton Input (active with voltage +9V)
IN3 Port 3 Output Pushbutton Input (active with voltage +9V)
IN4 Port 4 Output Pushbutton Input (active with voltage +9V)
IN5 Port 1 Break-in Input active with voltage of +9V
IN6 Port 2 Break-in Input active with voltage of +9V
IN7 Port 3 Break-in Input active with voltage of +9V
IN8 Port 4 Break-in Input active with voltage of +9V
NO1 Relay 1 N.O. contact
COM1 Relay 1 common
NC1 Relay 1 N.C. contact
NO2 Relay 2 N.O. contact
COM2 Relay 2 common
NC2 Relay 2 N.C. contact
NO3 Relay 3 N.O. contact
COM3 Relay 3 common
NC3 Relay 3 N.C. contact
NO4 Relay 4 N.O. contact
COM4 Relay 4 common
NC4 Relay 4 N.C. contact
NO5 Relay 5 N.O. contact
COM5 Relay 5 common
NC5 Relay 5 N.C. contact
NO6 Relay 6 N.O. contact
COM6 Relay 6 common
NC6 Relay 6 N.C. contact
NO7 Relay 7 N.O. contact
COM7 Relay 7 common
NC7 Relay 7 N.C. contact
NO8 Relay 8 N.O. contact
COM8 Relay 8 common
NC8 Relay 8 N.C. contact
Connector DB9 RS232 connector for printer or firmware upgrade from PC

MT4000-2 MT10000-4 ISMTUK_06_06.doc
Pag. 8
3. Wiring
MT4000-2 and MT10000-4 can be connected to a network of MT, TTD3000, M3000 or M5000 control units
using the RS485 bus.
Control unit configuration and access badge enable may be made via the keyboard and display (requires the
optional keypad/display kit) or via the optional SWAMIGO software.
Readers 1 and 2: proximity, magnetic, radio or keypad readers can be connected to Wiegand 26, Wiegand 30,
Wiegand 37, or Dataclock outputs.
RS232: a serial printer for the event printout or a PC/Notebook for firmware updating can be connected.
RS485: up to a maximum of 32 MT4000-2, MT10000-4, TTD3000, M3000 or M5000 control units can be
connected to the bus. Use an INT485C converter for control unit network management via PC.
Control unit or control unit network management via PC is made through the RS485 bus. Connection between
the PC on which the SWAMIGO software is installed and the RS485 bus may be made via Ethernet, the RS232
serial line, or the telephone line using INTETHERNET, INT485C, and INT485M converters, respectively, as
shown in the following figure
max 10 mt.
RS232
max 1000 mt.
RS485
max 100 mt.
Readers 1 and 2 Relay outputs
and digital inputs

MT4000-2 MT10000-4 ISMTUK_06_06.doc
Pag. 9
Wiring notes and recommendations:
•Maximum line lengths of readers 1 and 2 (control unit reader) is 100 meters
•Maximum RS485 bus length is 1000 metres.
•Maximum RS232 line length of 10 metres.
•Only use STP class 5 or FTP class 5 cables or superior.
•Connect reader – control unit wiring shielding to the GND of the control unit to which the wiring
is connected.
•Connect RS485 control unit – control unit wiring shielding with each other.
•Never connect reader – control unit and control unit – control unit wiring shielding with each
other.
•Never route system wiring in proximity to power cables.
•Never exceed 1A consumption when using external readers.
•Each control unit should be powered by the appropriate ALI13V8A3 or an equivalent power
supply unit with similar characteristics ( 13.8VDC, 3A)
•Any electric locks or external relays must be powered separately (see next paragraph) and must
be fitted with tension suppressors (included)
RS232, USB etc.
Telephone
line
IP Ethernet
RS232
INT485C
INT485M
INTETHERNET
RS485
Modem Modem

MT4000-2 MT10000-4 ISMTUK_06_06.doc
Pag. 10
3.1. Installation example with electric lock
A typical door-control installation with electric lock is made up as follows:
•1 in reader.
•1 out door-opening push-button.
•1 door-opening electric lock.
Connect in reader 1 to terminals D0.1, D1.1, GND, and +9V of the control unit.
Connect the electric lock to the terminal NO1 and through the power supply unit to the COM1.
Connect the manual door opening button between terminals IN1 and +9V of the control unit.
Using SWAMIGO software:
Duly configure reader 1 for relay 1 tripping
Duly configure the IN1 input for relay 1 tripping
Set relay 1 tripping and delay times to 1 and 0 seconds, respectively
Programme a badge for default access enable (5 Control Unit programming and testing, pag. 16).
Electric lock is activated for 1 second following valid read or pushing of manual opening out button.
Note 1: Power electric lock and control unit with separate power supply units.
Note 2: the figure shows the wiring with the MT4000-2 control unit terminal board but can easily be
applied to an installation with the MT10000-4 control unit.