Precision Digital Corporation ProVu PD6200 User manual

PROVU™PD6200 Analog Input Flow Rate/Totalizer
Instruction Manual
PRECISION DIGITAL CORPORATION
233 South Street • Hopkinton MA 01748 USA
Tel [phone] • Fax [phone]
www.predig.com
•1/8 DIN Digital Panel Flow Rate/Totalizers with NEMA 4X, IP65 Front
•0-20 mA, 4-20 mA, 0-5 V, 1-5 V, and ±10 V Inputs
•Dual-Line 6-Digit Display, 0.6" (15 mm) & 0.46" (12 mm)
•Isolated 24 VDC @ 200 mA Transmitter Power Supply
•2 or 4 Relays with Interlocking Capability + Isolated 4-20 mA Output Options
•Free PC-Based, On-Board, MeterView Pro USB Programming Software
•No Assembly Required
•Display Rate & Total at the Same Time
•Rate in Units per Second, Minute, Hour, or Day
•Total, Grand Total or Non-Resettable Grand Total
•Front Panel or Remote Total Reset
•Password Protection for Total Reset
•Total Stored in Non-Volatile Memory
•Assign Any Relay for Rate or Total
•4-20 mA Output for Rate or Total
•Sampling Relay
•Display Open Channel Flow with Programmable Exponent Feature
•32-Point Linearization & Square Root Extraction
•Optional SunBright Display Models for Outdoor Applications
•Operating Temperature Range: -40 to 65°C (-40 to 149°F)
•UL & C-UL Listed. E160849; 508 Industrial Control Equipment
•Input Power Options: 85-265 VAC / 90-265 VDC or 12-24 VDC / 12-24 VAC
•Programmable Display, Function Keys & Digital Input
•External 4-Relay & Digital I/O Modules
•RS-232 & RS-485 Serial Communication Options with Modbus RTU
•Wide Assortment of NEMA 4X Enclosures for up to Ten Meters
•Light / Horn & Reset Button Accessory
•Control Station Accessory for Remote Operation of PROVU
•3-Year Warranty
MeterView Pro
USB Install

PROVU™PD6200 Analog Input Flow Rate/Totalizer
Instruction Manual
2
Disclaimer
The information contained in this document is
subject to change without notice. Precision Digital
makes no representations or warranties with
respect to the contents hereof and specifically
disclaims any implied warranties of
merchantability or fitness for a particular purpose.
See Warranty Information and Terms &
Conditions on www.predig.com for complete
details.
•Read complete instructions prior to installation
and operation of the meter.
•Risk of electric shock or personal injury.
•This product is not recommended for life support
applications or applications where malfunctioning
could result in personal injury or property loss.
Anyone using this product for such applications
does so at his/her own risk. Precision Digital
Corporation shall not be held liable for damages
resulting from such improper use.
WARNING
Cancer and Reproductive Harm - www.P65Warnings.ca.gov
Limited Warranty
Precision Digital Corporation warrants this
product against defects in material or
workmanship for the specified period under
“Specifications” from the date of shipment from
the factory. Precision Digital’s liability under this
limited warranty shall not exceed the purchase
value, repair, or replacement of the defective unit.
See Warranty Information and Terms &
Conditions on www.predig.com for complete
details.
Registered Trademarks
All trademarks mentioned in this document are
the property of their respective owners.
© 2020 Precision Digital Corporation.
All rights reserved.
FREE MeterView Pro
Programming Software
The meter can be powered from the Micro USB connection.
When using the Micro USB connection, DO NOT apply AC or DC
power to the meter.
The easiest and quickest way to program your PROVU
meter is to use the FREE MeterView Pro
programming software. This software is loaded into
the meter and connects and installs directly to your
PC with a USB cable. We recommend that the first
thing you do after taking the meter out of the box is
connect the PROVUto your PC with the provided USB
cable –do not use a different cable. DO NOT apply
AC or DC power to the meter while your PC is
connected to the meter as it will disrupt the USB
connection. You don’t even have to apply an input
signal.
MeterView Pro programming software is intuitive, and
most customers can get their meter programmed as
they like without even looking in the manual.
Watch MeterView Pro Software Video at
www.predig.com/meterviewpro
In addition to programming, the software may be used
for:
•Monitoring
•Datalogging using your PC
•Generating and saving programming files for
later use
Once your meter is programmed the way you want it,
you can wire it up for your application per the
instructions in this manual and install it. If you find that
you need to make adjustments to the programming
after the meter is installed, you can use the front
panel buttons and the instructions in this manual to do
so.

PROVU™PD6200 Analog Input Flow Rate/Totalizer
Instruction Manual
3
Table of Contents
Introduction..........................................................................................................6
Using the PD6200 Like a PD6000 Process Meter .........................................6
Ordering Information...........................................................................................6
Specifications.......................................................................................................7
General.............................................................................................................7
Process Input...................................................................................................8
Rate/Totalizer...................................................................................................8
Relays...............................................................................................................9
Isolated 4-20 mA Transmitter Output ............................................................9
USB Connection............................................................................................10
On-Board Digital Input (F4)...........................................................................10
Modbus®RTU Serial Communications........................................................10
MeterView Pro................................................................................................10
Compliance Information....................................................................................11
Safety..............................................................................................................11
Electromagnetic Compatibility.....................................................................11
Safety Information .............................................................................................11
Installation..........................................................................................................11
Unpacking......................................................................................................11
Panel Mounting Instructions ........................................................................12
Mounting Dimensions..................................................................................12
Installation Overview.....................................................................................13
MeterView Pro Software................................................................................13
MeterView Pro Installation...........................................................................13
Transmitter Supply Voltage Selection (P+, P-)...........................................14
Connections...................................................................................................14
Connectors Labeling ...................................................................................14
Power Connections.....................................................................................15
Signal Connections .....................................................................................15
Modbus RTU Serial Communications.........................................................15
Relay Connections......................................................................................15
Switching Inductive Loads...........................................................................16
F4 Digital Input Connections.......................................................................16
4-20 mA Output Connections......................................................................16
Analog Output Power Supply......................................................................16
External Relay & Digital I/O Connections....................................................17
Interlock Relay Feature...............................................................................17
Setup and Programming...................................................................................18
Front Panel Buttons and Status LED Indicators ........................................18
Display Functions & Messages....................................................................19
Main Menu......................................................................................................21
Setting Numeric Values ................................................................................21
Setting Up the Rate/Totalizer Meter (setup)................................................21
Setting the Input Signal (Input)..................................................................22
Setting the Totalizer Features (total)........................................................22
Setting the Display Units or Custom Tags (units).....................................22
Setting the Decimal Point (dEc.pt) ..............................................................23
Programming the Rate/Totalizer (prog)......................................................23
Setting the Display Parameter & Intensity (dsplay) ...................................25
Display Intensity (d-Inty)...........................................................................25
Setting the Relay Operation (relay)...........................................................26
Relay Assignment (Assign)........................................................................26
Setting the Relay Action..............................................................................26
Programming Set and Reset Points............................................................27
Setting Fail-Safe Operation.........................................................................27
Programming Time Delay............................................................................27
Relay Action for Loss of 4-20 mA Input (Loop Break).................................27
Relay and Alarm Operation Diagrams.........................................................28
High Alarm Operation (Set >Reset)................................................................28
Low Alarm Operation (Set < Reset)............................................................28

PROVU™PD6200 Analog Input Rate/Totalizer
Instruction Manual
4
High Alarm with Fail-Safe Operation (Set > Reset).....................................28
Low Alarm with Fail-Safe Operation (Set < Reset) .....................................28
Time Delay Operation .................................................................................29
Rate Relay Sampling Operation..................................................................29
Total Relay Sampling Operation .................................................................29
Relay Operation Details................................................................................30
Overview .....................................................................................................30
Relays Auto Initialization.............................................................................30
Fail-Safe Operation.....................................................................................30
Front Panel LEDs........................................................................................30
Latching and Non-Latching Relay Operation ..............................................30
Non-Latching Relay (Auto) .........................................................................31
Non-Latching Relay with Manual Reset (A-nman).......................................31
Latching Relay with Clear (LatcH)..............................................................31
Latching Relay (Lt-Clr).............................................................................31
Acknowledging Relays................................................................................32
Setting Up the Interlock Relay (Force On) Feature.....................................32
Scaling the 4-20 mA Analog Output (Aout).................................................33
Reset Menu (reset).......................................................................................33
Manual Control Menu (Contrl).....................................................................33
Setting Up the Password (pass)...................................................................34
Protecting or Locking the Meter ..................................................................34
Total Reset Password & Non-Resettable Total...........................................34
Making Changes to a Password Protected Meter.......................................34
Disabling Password Protection....................................................................34
Advanced Features Menu.............................................................................35
Advanced Features Menu & Display Messages..........................................35
Noise Filter (filter)...................................................................................36
Noise Filter Bypass (bypass)......................................................................36
Rounding Feature (round)..........................................................................36
Modbus RTU Serial Communications (serial)..........................................36
Select Menu (SElEct).................................................................................37
Input Signal Conditioning (Functn).............................................................37
Low-Flow Cutoff (CutofF)...........................................................................38
Totalizer Count Up/Down (Count)...............................................................38
Analog Output Programming (AoutPr) .......................................................38
Programmable Function Keys User Menu (user).......................................39
Internal Source Calibration (ICAL) ..............................................................40
Meter Operation .................................................................................................41
Front Panel Buttons Operation ....................................................................41
Function Keys Operation..............................................................................41
F4 Operation ..................................................................................................41
Maximum/Minimum Readings......................................................................41
Totalizer Overflow Displays Total to 9 Digits..............................................41
Troubleshooting.................................................................................................42
Diagnostics Menu (diag) ..............................................................................42
Determining Software Version.....................................................................42
Reset Meter to Factory Defaults...................................................................42
Factory Defaults & User Settings................................................................43
Troubleshooting Tips....................................................................................44
EU Declaration of Conformity...........................................................................45

PROVU™PD6200 Analog Input Rate/Totalizer
Instruction Manual
5
Table of Figures
Figure 1: 1/8 DIN Panel Cutout and Mounting.................................................12
Figure 2. Meter Dimensions - Side View..........................................................12
Figure 3. Meter Dimensions - Top View...........................................................12
Figure 4: Transmitter Supply Voltage Selection.............................................14
Figure 5. PD6200-##0 Connectors Label .........................................................14
Figure 6. PD6200-##2 Connectors Label .........................................................14
Figure 7. PD6200-##3 Connectors Label .........................................................14
Figure 8. PD6200-##4 Connectors Label .........................................................14
Figure 9. PD6200-##5 Connectors Label .........................................................14
Figure 10. PD6200-##7 Connectors Label .......................................................14
Figure 11: Power Connections.........................................................................15
Figure 12: Transmitter Powered by Internal Supply.......................................15
Figure 13: Transmitter Powered by External Supply or Self-Powered.........15
Figure 14: Voltage Input Connections.............................................................15
Figure 15: Relay Connections ..........................................................................15
Figure 16: AC and DC Loads Protection..........................................................16
Figure 17: Low Voltage DC Loads Protection.................................................16
Figure 18: F4 Digital Input Connections..........................................................16
Figure 19: 4-20 mA Output Connections.........................................................16
Figure 20. Analog Output Supply Powering Other Devices...........................16
Figure 21. Expansion Module & DIN Rail Mounting Kit..................................17
Figure 22. External Relays Module Connections............................................17
Figure 23. Digital I/O Module Connections......................................................17
Figure 24. Interlock Connection.......................................................................17

PROVU™PD6200 Analog Input Rate/Totalizer
Instruction Manual
6
Introduction
Front, back and in between, the PROVUmeter boasts
specifications, features and functionality that make it
the only 1/8 DIN analog input flow rate/totalizer you
will ever need. The number one feature that makes
the PROVUsuch a useful device is its built-in 24 VDC
@ 200 mA power supply to drive the transmitter. This
feature not only saves the cost of an external power
supply, but also greatly simplifies wiring. In addition,
there is a second 24 VDC @ 40 mA power supply
provided with the 4-20 mA output option.
The second most important feature about these
meters is they can display flow rate and total at the
same time. In fact, the 6-digit dual line display can be
programmed for a wide variety of flow applications,
including: flow rate and tag, total and tag, total and
grand total, and even non-resettable grand total.
Another reason why the PROVUMeter is the only flow
rate/totalizer you will ever need is its NEMA 4X rated
front panel. This means you can install the PROVUin
panels exposed to moisture, dust and other adverse
conditions. The PROVUis also available with an
optional Sunbright display which means you can
install and read the PROVUin direct sunlight.
Other key features include four relays and 4-20 mA
output option, remote total reset, advanced input
signal conditioning like square root extraction and
programmable exponent for open channel flow.
Finally, all these features and capabilities can easily
be programmed with free MeterView Pro software.
Using the PD6200 Like a
PD6000 Process Meter
The PD6200 is essentially a PD6000 process meter
with flow totalization capability. The flow totalization
capability can easily be de-activated for customers
that would prefer their PD6200 behave like a PD6000
process meter. For instructions on how to do this, see
Setting Up the Rate/Totalizer Meter (setup) on page
21 for details.
Ordering Information
Standard Models
85-265 VAC
Model
12-24 VDC
Model
Options Installed
PD6200-6R0
PD6200-7R0
No options
PD6200-6R2
PD6200-7R2
2 relays
PD6200-6R3
PD6200-7R3
4-20 mA output
PD6200-6R4
PD6200-7R4
4 relays
PD6200-6R5
PD6200-7R5
2 relays& 4-20 mA output
PD6200-6R7
PD6200-7R7
4 relays & 4-20 mA output
SunBright Display Models
85-265 VAC
Model
12-24 VDC
Model
Options Installed
PD6200-6H0
PD6200-7H0
No options
PD6200-6H2
PD6200-7H2
2 relays
PD6200-6H3
PD6200-7H3
4-20 mA output
PD6200-6H4
PD6200-7H4
4 relays
PD6200-6H5
PD6200-7H5
2 relays &4-20 mA output
PD6200-6H7
PD6200-7H7
4 relays& 4-20 mA output
Accessories
Model
Description
PDA1002
DIN rail mounting kit for two devices
PDA1004
4 SPST (Form A) relays module
PDA1044
4 digital inputs & 4 digital outputs module
PDA1232
RS-232 serial adapter
PDA1485
RS-485 serial adapter
PDA7485-I
RS-232 to RS-485 isolated converter
PDA8008
USB Adapter
PDA8232-N
USB to RS-232 non-isolated converter
PDA8485-I
USB to RS-485 isolated converter
PDA-LH
Light / horn accessory
MOD-LH
Light / horn / enclosure modification
PDA2360
Plastic control stations series
PD659
Signal isolators, splitters, & conditioners
PD9501
Multi-function calibrator
PD9502
Low-cost signal generator
PDX6901
Snubber: 0.01 μF/470 Ω, 250 VAC
Enclosures
Series
Meters
Material
PDA2300
1-10
Plastic NEMA 4X
PDA2500
1-6
Plastic NEMA 4X
PDA2600
1-6
Stainless Steel NEMA 4X
PDA2700
1-6
Painted Steel NEMA 4
PDA2800
1-2
Plastic NEMA 4X
PDA3400
1-3
Plastic NEMA 4X
Need help selecting the right enclosure?
Go to www.predig.com/esu
Replacement Option Cards
Model
Options Installed
PD1102
2 relays
PD1103
4-20 mA output
PD1104
4 relays
PD1105
2 relays& 4-20 mA output
PD1107
4 relays & 4-20 mA output

PROVU™PD6200 Analog Input Rate/Totalizer
Instruction Manual
7
Specifications
Except where noted all specifications apply to
operation at +25°C.
General
Display
Line 1: 0.6" (15 mm) high, red LEDs
Line 2: 0.46" (12 mm) high, red LEDs
6 digits: each (-99999 to 999999), with lead
zero blanking.
Display
Intensity
Eight user selectable intensity levels.
Default value is six.
Display
Update Rate
5/second (200 ms)
Overrange
Display flashes 999999
Underrange
Display flashes -99999
Display
Assignment
Display lines 1 & 2 may be assigned to
rate, total, grand total, alternate (rate/total,
rate/grand total, rate/units, total/units, and
grand total/units), set points, max/min, units
(line 2 only), and Modbus input. Additional
displays are available if parameter total is
off, and parameter d-SCAL is on: gross,
alternating gross/net, PV1, PV2, and PCT
(refer to PD6000 instruction manual at
www.predig.com).
Programming
Methods
Four front panel buttons, digital inputs, or
PC with MeterView Pro software.
Noise Filter
Programmable from 2 to 199
(0 will disable filter)
Filter Bypass
Programmable from 0.1 to 99.9% of
calibrated span
Recalibration
All ranges are calibrated at the factory.
Recalibration is recommended at least
every 12 months.
Max/Min
Display
Max/min readings reached by the process
are stored until reset by the user or until
power to the meter is turned off.
Rounding
Select 1, 2, 5, 10, 20, 50, or 100
(e.g. rounding = 10, value = 123.45,
display = 123.50).
Password
Three programmable passwords restrict
modification of programmed settings and
two prevent resetting the totals.
Pass 1: Allows use of function keys and
digital inputs
Pass 2: Allows use of function keys, digital
inputs and editing set/reset points
Pass 3: Restricts all programming, function
keys, and digital inputs.
Total: Prevents resetting the total manually
Gtotal: Prevents resetting the grand total
manually
Non-Volatile
Memory
All programmed settings are stored in
non-volatile memory for a minimum of ten
years if power is lost.
Power
Options
85-265VAC50/60Hz;90-265VDC,20Wmax;
12-24 VDC, 12-24 VAC, 15 W max.
Powered over USB for configuration only.
Fuse
Required external fuse: UL Recognized,
5 A max, slow blow; up to 6 meters may
share one 5 A fuse
Normal Mode
Rejection
Greater than 60 dB at 50/60 Hz
Isolation
4 kV input/output-to-power line
500 V input-to-output or output-to-P+ supply
Overvoltage
Category
Installation Overvoltage Category II:
Local level with smaller transient
overvoltages than Installation Overvoltage
Category III.
Environmental
Operating temperature range:
-40 to 65°C (-40 to 149°F)
Storage temperature range:
-40 to 85°C (-40 to 185°F)
Relative humidity:
0 to 90% non-condensing
Connections
Removable screw terminal blocks accept
12 to 22 AWG wire, RJ45 for external
relays, digital I/O, and serial communication
adapters.
Enclosure
1/8 DIN, high impact plastic, UL 94V-0,
color: black
Front Panel
NEMA 4X, IP65
Mounting
1/8 DIN panel cutout required:
3.622" x 1.772" (92 mm x 45 mm)
Two panel mounting bracket assemblies
are provided.
Tightening
Torque
Screw terminal connectors: 5 lb-in
(0.56 Nm)
Overall
Dimensions
4.68" x 2.45" x 5.64"
(119 mm x 62 mm x 143 mm)
(W x H x D)
Weight
9.5 oz (269 g)
Warranty
3 years parts & labor. See Warranty
Information and Terms & Conditions on
www.predig.com for complete details.

PROVU™PD6200 Analog Input Rate/Totalizer
Instruction Manual
8
Process Input
Inputs
Field selectable: 0-20 mA, 4-20 mA
10 V (0-5 V, 1-5 V, 0-10 V)
Modbus PV (Slave)
Isolated
Transmitter
Power Supply
Terminals P+ & P-: 24 VDC 10%.
All models selectable for 24, 10, or 5 VDC
supply (internal jumper J4). 85-265 VAC
models rated @ 200 mA max, 12-24 VDC
powered models rated @ 100 mAmax.
5 & 10 VDC supplyrated @ 50 mA max.
Refer to Figure 4: Transmitter Supply Voltage
Selection on page 14 and
Figure 19: 4-20 mA Output Connections on
page 16.
When the Light / Horn is powered by the
transmitter power supply, see MOD-LH
Light / Horn's transmitter power supply
specification in MOD-LH manual for
additional details. Light / Horn power not
available for 5 or 10 VDC supplies.
Accuracy
±0.03% of calibrated span ±1 count,
square root & programmable exponent
accuracy range: 10-100% of calibrated
span
Temperature
Drift
0.005% of calibrated span/C max from
0 to 65C ambient, 0.01% of calibrated
span/C max from -40 to 0C ambient
Input Signal
Conditioning
Linear, square root, programmable
exponent, or round horizontal tank volume
calculation
Multi-Point
Linearization
2 to 32 points
Programmable
Exponent
User selectable from 1.0001 to 2.9999 for
open channel flow
Round
Horizontal
Tank
Diameter & Length: 999.999 inch or cm
calculates volume in gallons or liters
respectively.
Low-Flow
Cutoff
0.0 to 999,999.9 (0 disables cutoff
function). Point below at which display
always shows zero.
Decimal Point
Up to five decimal places or none:
d.ddddd, d.dddd, d.ddd, d.dd, d.d, or dddddd
Calibration
Range
Input Range
Minimum Span
Input 1 & Input 2
4-20 mA
0.15 mA
10 V
0.10 V
An error message will appear if the input 1
and input 2 signals are too close together.
Input
Impedance
Voltage ranges: greater than 500 k
Current ranges: 50 - 100 (depending on
resettable fuse impedance)
Input
Overload
Current input protected by resettable fuse,
30 VDC max. Fuse resets automatically
after fault is removed.
HART
Transparency
The meter does not interfere with existing
HART communications; it displays the
4-20 mA primary variable and it allows the
HART communications to pass through
without interruption. The meter is not
affected if a HART communicator is
connected to the loop. The meter does not
display secondary HART variables.
Rate/Totalizer
Rate Display
Indication
-99999 to 999999, lead zero blanking.
“R” LED illuminates while displaying rate.
Total Display
& Total
Overflow
0 to 999,999; automatic lead zero blanking.
“T” LED is illuminated while displaying total
or grand total.
Up to 999,999,999 with total-overflow
feature. “oF” is displayed to the left of total
overflow and ▲ LED is illuminated.
Total
Decimal Point
Up to five decimal places or none:
d.ddddd, d.dddd, d.ddd, d.dd, d.d, or dddddd
Total decimal point is independent of rate
decimal point.
Totalizer
Calculates total based on rate and field
programmable multiplier to display total in
engineering units. Time base must be
selected according to the time units in
which the rate is displayed.
Totalizer
Rollover
Totalizer rolls over when display exceeds
999,999,999. Relay status reflects display.
Total
Overflow
Override
Program total reset for automatic with
0.1 second delay and set point 1 for
999,999
Totalizer
Presets
Up to eight, user selectable under setup
menu. Any set point can be assigned to
total and may be programmed anywhere in
the range of the meter for total alarm
indication.
Programmable
Delay
On Release
0.1 and 999.9 seconds; applied to the first
relay assigned to total or grand total.
If the meter is programmed to reset total to
zero automatically when the preset is
reached, then a delay will occur before the
total is reset.
Total Reset
User selectable via front panel button, F4
terminal at back of meter, external contact
closure on digital inputs, automatically via
user selectable preset value and time
delay, or through serial communications.
Total Reset
Password
Total and grand total passwords may be
entered to prevent resetting the total or
grand total from the front panel.
Non-Resettable
Total
The grand total can be programmed as a
non-resettable total by entering the
password “050873”.
•Once the Grand Total has been programmed as
“non-resettable” the feature CANNOT be
disabled.

PROVU™PD6200 Analog Input Rate/Totalizer
Instruction Manual
9
Relays
Rating
2 or 4 SPDT (Form C) internal and/or
4 SPST (Form A) external; rated 3 A
@ 30 VDC and 125/250 VAC resistive load;
1/14 HP (≈50 W) @ 125/250 VAC for
inductive loads
Noise
Suppression
Noise suppression is recommended for
each relay contact switching inductive
loads. See Switching Inductive Loads on
page 16 for details.
Relay
Assignment
Relays may be assigned to rate, total, or
grand total.
Deadband
0-100% of span, user programmable
High or Low
Alarm
User may program any alarm for high or
low trip point. Unused alarm LEDs and
relays may be disabled (turn off).
Relay
Operation
•Automatic (non-latching) and/or
manual reset
•Latching (requires manual
acknowledge) with or without clear
•Pump alternation control (2-8 relays)
•Sampling (based on set point and time)
•Off (disable unused relays and enable
Interlock feature)
•Manual on/off control mode
Relay Reset
User selectable via front panel button, F4
terminal at back of meter, external contact
closure on digital inputs, automatically via
user selectable preset value and time
delay, or through serial communications.
Time Delay
0 to 999.9 seconds, on & off relay time
delays. Programmable and independent for
each relay.
Fail-Safe
Operation
Programmable and independent for each
relay.
Note: Relay coil is energized in non-alarm
condition. In case of power failure, relay
will go to alarm state.
Auto
Initialization
When power is applied to the meter, relays
will reflect the state of the input to the
meter.
Additional
Relays
An external module, model PDA1004, is
available to add 4 SPST 3 A relays to the
meter.
Isolated 4-20 mA Transmitter
Output
Output Source
Rate/process, total, grand total, max, min,
set points 1-8, or manual control mode
Scaling Range
1.000 to 23.000 mA for any display range.
Calibration
Factory calibrated:
4.000 to 20.000 = 4-20 mA output
Analog Out
Programming
23.000 mA maximum for all parameters:
Overrange, underrange, max, min, and
break
Accuracy
± 0.1% FS ± 0.004 mA
Temperature
Drift
0.4 µA/C max from 0 to 65C ambient,
0.8 µA/C max from -40 to 0C ambient
Note: Analog output drift is separate from
input drift.
Isolated
Transmitter
Power Supply
Terminals I+ & R: 24 VDC 10%. May be
used to power the 4-20 mA output or other
devices.
All models rated @ 40 mA max.
External Loop
Power Supply
35 VDC maximum
Output Loop
Resistance
Power supply
Minimum
Maximum
24 VDC
10 
700 
35 VDC
(external)
100 
1200 
Additional
4-20 mA
Outputs
The PD659-1MA-2MA can split the optional
4-20 mA output into two isolated 4-20 mA
outputs
0-10 VDC
Output
The PD659-1MA-1V can convert the
optional 4-20 mA output to a 0-10 VDC
output

PROVU™PD6200 Analog Input Rate/Totalizer
Instruction Manual
10
USB Connection
Function
Programming only
Compatibility
USB 2.0 Standard, Compliant
Connector
Type
Micro-B receptacle
Cable
USB A Male to Micro-B Cable
Driver
Microsoft®Windows®XP/Vista/7/8/10
Power
USB port provides power to the meter.
DO NOT apply AC or DC power to the
meter while the USB port is in use.
On-Board Digital Input (F4)
Function
Reset total, remote operation of front-panel
buttons, acknowledge/reset relays, reset
max/min values. See Function Keys &
Digital I/O Available Settings on page 39 for
a complete list of capabilities.
Contacts
3.3 VDC on contact. Connect normally
open contacts across F4 to COM
Logic Levels
Logic High: 3 to 5 VDC
Logic Low: 0 to 1.25 VDC
Additional I/O
Up to 2 external modules, model PDA1044
with 4 digital inputs and 4 digital outputs
each can be added.
Modbus®RTU Serial
Communications
Slave Id
1 –247 (Meter address)
Baud Rate
300 - 19,200 bps
Transmit
Time Delay
Programmable between 0 and 199 ms
Data
8 bit (1 start bit, 1 or 2 stop bits)
Parity
Even, Odd, or None with 1 or 2 stop bits
Byte-To-Byte
Timeout
0.01 –2.54 second
Turn Around
Delay
Less than 2 ms (fixed)
Note: Refer to the PROVUModbus Register Tables located
at www.predig.com for details.
MeterView Pro
Availability
Download directly from meter or from
www.predig.com/download_software
System
Requirements
Microsoft®Windows®XP/Vista/7/8/10
Communications
USB 2.0 (for programming only)
(Standard USB A to Micro USB B)
RS-232 adapter, RS-485 adapter and
RS-485 to USB converter
(programming, monitoring, and data
logging)
Configuration
Configure meters one at a time
Power
USB port provides power to the meter.
DO NOT apply AC or DC power to the
meter while the USB port is in use.

PROVU™PD6200 Analog Input Rate/Totalizer
Instruction Manual
11
Compliance Information
Safety
UL & c-UL
Listed
USA & Canada
UL 508 Industrial Control Equipment
UL File Number
E160849
Front Panel
UL Type 4X, NEMA 4X, IP65; panel
gasket provided
Low Voltage
Directive
EN 61010-1:2010
Safety requirements for measurement,
control, and laboratory use
Electromagnetic Compatibility
Emissions
EN 55022:2010
Class A ITE emissions requirements
Radiated
Emissions
Class A
AC Mains
Conducted
Emissions
Class A
Immunity
EN 61326-1:2013
Measurement, control, and laboratory
equipment
EN 61000-6-2:2005
EMC heavy industrial generic immunity
standard
RFI -
Amplitude
Modulated
80 -1000 MHz 10 V/m 80% AM (1 kHz)
1.4 - 2.0 GHz 3 V/m 80% AM (1 kHz)
2.0 - 2.7 GHz 1 V/m 80% AM (1 kHz)
Electrical
Fast
Transients
±2kV AC mains, ±1kV other
Electrostatic
Discharge
±4kV contact, ±8kV air
RFI -
Conducted
10V, 0.15-80 MHz, 1kHz 80% AM
AC Surge
±2kV Common, ±1kV Differential
Surge
1KV (CM)
Power-
Frequency
Magnetic
Field
30 A/m 70%V for 0.5 period
Voltage Dips
40%V for 5 & 50 periods
70%V for 25 periods
Voltage
Interruptions
<5%V for 250 periods
Note:
Testing was conducted on meters installed through the
covers of grounded metal enclosures with cable shields
grounded at the point of entry representing installations
designed to optimize EMC performance.
Safety Information
•Read complete instructions prior to installation
and operation of the meter.
•Risk of electric shock or personal injury.
•Hazardous voltages exist within enclosure.
Installation and service should be performed only
by trained service personnel.
Installation
There is no need to remove the meter from its
case to complete the installation, wiring, and
setup of the meter for most applications.
Instructions are provided for changing the
transmitter power supply to output 5 or 10 VDC
instead of 24 VDC. See Figure 4: Transmitter
Supply Voltage Selection on page 14.
Unpacking
Remove the meter from box. Inspect the
packaging and contents for damage. Report
damages, if any, to the carrier.
If any part is missing or the meter malfunctions,
please contact your supplier or the factory for
assistance.

PROVU™PD6200 Analog Input Rate/Totalizer
Instruction Manual
12
Panel Mounting Instructions
•Prepare a standard 1/8 DIN panel cutout –
3.622" x 1.772" (92 mm x 45 mm). Refer to
Figure 1: 1/8 DIN Panel Cutout and Mounting
below for more details.
•Clearance: allow at least 6.0" (152 mm) behind
the panel for wiring.
•Panel thickness: 0.04" - 0.25" (1.0 mm - 6.4 mm).
Recommended minimum panel thickness to
maintain Type 4X rating: 0.06" (1.5 mm) steel
panel, 0.16" (4.1 mm) plastic panel.
•Remove the two mounting brackets provided with
the meter (back-off the two screws so that there is
¼" (6.4 mm) or less through the bracket. Slide the
bracket toward the front of the case and remove).
•Insert meter into the panel cutout.
•Install mounting brackets and tighten the screws
against the panel. To achieve a proper seal,
tighten the mounting bracket screws evenly until
meter is snug to the panel along its short side.
DO NOT OVER TIGHTEN, as the rear of the
panel may be damaged.
DO NOT apply AC or DC power to the meter when using the
Micro USB connection.
Figure 1: 1/8 DIN Panel Cutout and Mounting
Mounting Dimensions
Figure 2. Meter Dimensions - Side View
Figure 3. Meter Dimensions - Top View
NO NC NC C NO C
NO NC NC C NO C+ -R
3.622" (92 mm)
1.772"
(45mm)
Panel Cutout
to DIN 43700
Square Corners to 0.060"
(1.5mm) Max Radius
A
B
Tolerances:
A: +0.032 (+0.8mm)
-0.000 (-0.0mm)
B: +0.024 (+0.6mm)
-0.000 (-0.0mm)

PROVU™PD6200 Analog Input Rate/Totalizer
Instruction Manual
13
Installation Overview
We recommend the following sequence for getting the
meter into service:
1. DO NOT apply AC or DC power to the meter.
2. Connect the meter to the PC with the USB cable
provided. DO NOT use a different USB cable.
3. If MeterView Pro (MVPro) is already installed in
your computer, then the program will launch
automatically in most systems. If the program
does not start automatically, double-click on the
MVPro icon.
4. If MVPro is not installed, follow the instructions
provided below.
5. Use MVPro to configure the meter for your
application.
6. Disconnect the USB cable from the meter.
7. Apply power and signal and check operation of
the meter.
8. Install the meter and put into service.
9. Make any programming adjustments using the
front panel buttons.
MeterView Pro Software
The easiest and quickest way to program your PROVU
meter is to use the FREE MeterView Pro
programming software. This software is loaded into
the meter and connects and installs directly to your
PC with the USB cable provided. DO NOT use a
different USB cable. We recommend that the first
thing you do after taking the meter out of the box is
connect the PROVUto your PC with the provided USB
cable. DO NOT apply AC or DC power to the meter
while your PC is connected to the meter as it will
disrupt the USB connection. It is not necessary to
apply an input signal.
MeterView Pro programming software is intuitive, and
most customers can get their meter programmed as
they like without even looking in the manual.
Watch Meterview Pro Software Video at
www.predig.com/meterviewpro
MeterView Pro Installation
1. Connect one end of the provided USB cable
to the meter and the other end to the
computer. The computer will automatically
install the driver software it needs to talk to
the meter. Follow the on-screen instructions
and allow sufficient time for the process to
complete. This can take a few minutes. If the
process is interrupted, then it could leave the
system in an unstable condition.
•Only one meter may be connected at a time.
Attaching multiple meters will cause a conflict
with the meter software.
•DO NOT apply AC or DC power to the meter
when using the Micro USB connection.
2. Once the driver is installed, an AutoPlay
dialog should appear for the drive
“MAINSTAL.” Click “Open folder to view
files.”
If the computer does not display an AutoPlay
dialog for the drive “MAINSTAL,” you should
open My Computer and double-click on the
drive labeled “MAINSTAL.”
3. Double-click on the file named “MAStart.”
The program will open a few windows and
install two programs on your computer.
Simply follow the on-screen instructions until
you see one of the dialogs below. If you
receive a “User Account Control” warning,
click “Yes.”
4. If there is an update available, click the
“Update” button to install the new version.
Otherwise, click “Configure” to begin
programming your meter.
Note: If you decide to update your MeterView Pro
software, once the installation has completed, you
will be asked if you want to update the setup files
located on the meter itself. This way, you will
always have the most current version on the meter
for future installs.
•DO NOT unplug the meter while the new
installation files are being written to it. The meter
will display uwrite during the process and you
will receive an on-screen notification once the
process is complete.

PROVU™PD6200 Analog Input Rate/Totalizer
Instruction Manual
14
Transmitter Supply Voltage
Selection (P+, P-)
All meters, including models equipped with the
12-24 VDC power option, are shipped from the
factory configured to provide 24 VDC power for
the transmitter or sensor.
If the transmitter requires 5 or 10 VDC excitation,
the internal jumper J4 must be configured
accordingly.
To access the voltage selection jumper:
1. Remove all the connectors.
2. Unscrew the back cover.
3. Slide the back cover about 1 inch.
4. Configure the J4 jumper, located behind the
input signal connector, for the desired
excitation voltage as shown.
Figure 4: Transmitter Supply Voltage Selection
Connections
All connections are made to removable screw
terminal connectors located at the rear of the
meter.
•Use copper wire with 60°C or 60/75°C insulation
for all line voltage connections. Observe all safety
regulations. Electrical wiring should be performed
in accordance with all applicable national, state,
and local codes to prevent damage to the meter
and ensure personnel safety.
Connectors Labeling
The connectors’ label, affixed to the meter, shows the
location of all connectors available with requested
configuration.
Note: ## on the following figures refers to power and
display options. (Example: PD6200-6H5)
Figure 5. PD6200-##0 Connectors Label
Figure 6. PD6200-##2 Connectors Label
Figure 7. PD6200-##3 Connectors Label
Figure 8. PD6200-##4 Connectors Label
Figure 9. PD6200-##5 Connectors Label
Figure 10. PD6200-##7 Connectors Label
•DO NOT connect any equipment other than
Precision Digital’s expansion modules, cables, or
meters to the RJ45 M LINK connector. Otherwise
damage will occur to the equipment and the
meter.
POWER
+-
SIGNAL
M-LINK
123 4 5 6 7 8
21
P- COMP+ V+ mA+
3412 5
F4
6
POWER
+-
SIGNAL
M-LINK
CNONO NC NC C
RELAY2 RELAY1
4365 21
123 4 5 6 7 8
21
P- COMP+ V+ mA+
3412 5
F4
6
R
I- I+
MA OUT
1
32
POWER
+-
SIGNAL
M-LINK
123 4 5 6 7 8
21
24 V
P- COMP+ V+ mA+
3412 5
F4
6
POWER
+-
SIGNAL
M-LINK
CNONO NC NC C
RELAY4 RELAY3
4365 2 1
CNONO NC NC C
RELAY2 RELAY1
4365 21
123 4 5 6 7 8
21
P- COMP+ V+ mA+
3412 5
F4
6
R
I- I+
MA OUT
1
32
POWER
+-
SIGNAL
M-LINK
CNONO NC NC C
RELAY2 RELAY1
4365 21
123 4 5 6 7 8
21
24 V
P- COMP+ V+ mA+
3412 5
F4
6
R
I- I+
MA OUT
1
32
POWER
+-
SIGNAL
M-LINK
CNONO NC NC C
RELAY4 RELAY3
4365 2 1
CNONO NC NC C
RELAY2 RELAY1
4365 21
123 4 5 6 7 8
21
24 V
P- COMP+ V+ mA+
3412 5
F4
6

PROVU™PD6200 Analog Input Rate/Totalizer
Instruction Manual
15
Power Connections
Power connections are made to a two-terminal
connector labeled POWER. The meter will operate
regardless of DC polarity connection. The + and -
symbols are only a suggested wiring convention.
Figure 11: Power Connections
Signal Connections
Signal connections are made to a six-terminal
connector labeled SIGNAL. The COM (common)
terminal is the return for the 4-20 mA and the 10 V
input signals.
Current and Voltage Connections
The following figures show examples of current and
voltage connections.
There are no switches or jumpers to set up for current
and voltage inputs. Setup and programming is
performed through the front panel buttons.
Figure 12: Transmitter Powered by Internal Supply
Figure 13: Transmitter Powered by External
Supply or Self-Powered
The current input is protected against current
overload by a resettable fuse. The display may or
may not show a fault condition depending on the
nature of the overload.
The fuse limits the current to a safe level when it
detects a fault condition, and automatically resets
itself when the fault condition is removed.
Figure 14: Voltage Input Connections
The meter is capable of accepting any voltage from -
10 VDC to +10 VDC.
Modbus RTU Serial
Communications
Serial communications connection is made to an
RJ45 connector labeled M-LINK on. For interfacing to
the PROVU, use the PDA1232 for RS-232 or the
PDA1485 for RS-485. The same port is used for
interfacing with all expansion modules (e.g. external
relays, digital I/O).
Relay Connections
Relay connections are made to two six-terminal
connectors labeled RELAY1 –RELAY4. Each relay’s
C terminal is common only to the normally open (NO)
and normally closed (NC) contacts of the
corresponding relay. The relays’ C terminals should
not be confused with the COM (common) terminal of
the INPUT SIGNAL connector.
Figure 15: Relay Connections
AC or DC
POWER
Required External Fuse:
5 A max, 250 V Slow Blow
POWER
+-
CNONO NC NC C
RELAY4 RELAY3
4 36 5 2 1
CNONO NC NC C
RELAY2 RELAY1
4 36 5 2 1

PROVU™PD6200 Analog Input Rate/Totalizer
Instruction Manual
16
Switching Inductive Loads
The use of snubbers to suppress electrical noise is
strongly recommended when switching inductive
loads to prevent disrupting the microprocessor’s
operation. The snubbers also prolong the life of the
relay contacts. Suppression can be obtained with
resistor-capacitor (RC) networks assembled by the
user or purchased as complete assemblies. Refer to
the following circuits for RC network assembly and
installation:
Figure 16: AC and DC Loads Protection
Choose R and C as follows:
R: 0.5 to 1 for each volt across the contacts
C: 0.5 to 1 µF for each amp through closed contacts
Notes:
1. Use capacitors rated for 250 VAC.
2. RC networks may affect load release time of
solenoid loads. Check to confirm proper
operation.
3. Install the RC network at the meter's relay screw
terminals. An RC network may also be installed
across the load. Experiment for best results.
Use a diode with a reverse breakdown voltage two to three
times the circuit voltage and forward current at least as large
as the load current.
Figure 17: Low Voltage DC Loads Protection
RC Networks (Snubbers) Available
from Precision Digital
RC networks are available from Precision Digital and
should be applied to each relay contact switching an
inductive load. Part number: PDX6901.
Note: Relays are de-rated to 1/14th HP (50 watts)
with an inductive load.
F4 Digital Input Connections
A digital input, F4, is standard on the meter. This
digital input should be connected with a normally
open contact across F4 and COM, or with an active
low signal applied to F4. It can be used to reset the
total, for remote operation of front-panel buttons, to
acknowledge/reset relays, or to reset max/min values.
See Function Keys & Digital I/O Available Settings on
page 39 for a complete list of capabilities.
Figure 18: F4 Digital Input Connections
4-20 mA Output Connections
Connections for the 4-20 mA transmitter output are
made to the connector terminals labeled mA OUT.
The 4-20 mA output may be powered internally or
from an external power supply.
Figure 19: 4-20 mA Output Connections
Analog Output Power Supply
The internal 24 VDC power supply powering the
analog output may be used to power other devices, if
the analog output is not used. The I+ terminal is the
+24 V and the R terminal is the return.
Figure 20. Analog Output Supply Powering Other
Devices
C
R
C
R
P- COMP+ V+ mA+
3412 5
F4
6
4-20 mA Input
Remote Display, PLC,
Chart Recorder, Etc.
-
+
RI- I+ 132
RELAY1 mA OUT
24 V
12-35 VDC
Power
Supply
+
4-20 mA
Input Meter
-+
RI- I+ 132
RELAY1
321
-
24 V
mA OUT
Internal Power Supply
and Analog Output
321
Active Output Loop Passive Output Loop
RI- I+
132
24 VDC
Powered
Device
24 V
+-

PROVU™PD6200 Analog Input Rate/Totalizer
Instruction Manual
17
External Relay & Digital I/O
Connections
The relay and the digital I/O expansion modules
PDA1004 & PDA1044 are connected to the meter
using a CAT5 cable provided with each module. The
two RJ45 connectors on the expansion modules are
identical and interchangeable; they are used to
connect additional modules to the system.
Note: The jumper located between the RJ45
connectors of the PDA1044 must be removed
on the second digital I/O module in order for the
system to recognize it as module #2.
•DO NOT connect or disconnect the expansion
modules with the power on! More detailed
instructions are provided with each optional
expansion module.
Figure 21. Expansion Module & DIN Rail Mounting
Kit
Figure 22. External Relays Module Connections
Figure 23. Digital I/O Module Connections
Interlock Relay Feature
As the name implies, the interlock relay feature
reassigns one, or more, alarm/control relays for use
as interlock relay(s). Interlock contact(s) are wired to
digital input(s) and activate the interlock relay. This
feature is enabled by configuring the relay, and the
corresponding digital input(s), see Setting Up the
Interlock Relay (Force On) Feature on page 32.
In the example below, an Interlock Contact switch is
connected to a digital input, which will be used to
force on (energize) the Interlock Relay. The Interlock
Relay and the Control Relay are connected in series
with the load.
•When the Interlock Contact is closed (safe), the
Interlock Relay energizes, allowing power to flow
to the Control Relay; the corresponding front
panel LED is on.
•When the Interlock Contact is open, the
corresponding front panel LED flashes (locked
out), the Interlock Relay is de-energized,
preventing power from flowing to the Control
Relay and the load.
.
Figure 24. Interlock Connection
1 2
RLY5 RLY6 RLY7 RLY8
3 4 5 6 7 8
NO CNO CNO CNO C
1 2 3 4 5 6
+5 I1 I2 I3 I4 O1
7 8
O2 O3
910
O4 G
DI 1-4 DO 1-4
5 VDC GND

PROVU™PD6200 Analog Input Rate/Totalizer
Instruction Manual
18
Setup and Programming
There is no need to recalibrate the meter
when first received from the factory.
The meter is factory calibrated prior to
shipment for milliamps and volts with
calibration equipment that is certified to NIST
standards.
Overview
There are no jumpers to set for the meter input
selection.
Setup and programming is done using MeterView Pro
or through the front panel buttons.
After power and input signal connections have been
completed and verified, apply power to the meter.
Front Panel Buttons and Status
LED Indicators
Button
Description
LED
Status
Menu
1-8
Alarm 1 –8
indicators
Right
arrow/F1
1-8
M
Flashing:
Relay in
manual
control mode
Up arrow/F2
R
Rate
indicator
Enter/F3
T
Total
indicator or
Flashing:
Tare
Note:
F4 is a digital input. Alarms
5-8 are enabled when relay
expansion module is
installed.
G T
Grand Total
indicator
▲
Total
overflow
indicator
Note:
LEDs for relays in manual mode flash with the “M” LED
every 10 seconds. “M” flashing by itself indicates Aout –
manual control is used.
•Press the Menu button to enter or exit the
Programming Mode at any time.
•Press the Right arrow button to move to the next
digit during digit
or decimal point programming.
•Press or hold the Up arrow button to scroll
through the menus, decimal point, or to
increment the value of a digit.
•Press the Enter button to access a menu or to
accept a setting.
•Press and hold the Menu button for three
seconds to access the advanced features of the
meter.

PROVU™PD6200 Analog Input Rate/Totalizer
Instruction Manual
19
Display Functions & Messages
The meter displays various functions and messages
during setup, programming, and operation. The
following table shows the main menu functions and
messages in the order they appear in the menu.
Display Functions & Messages
Display
Parameter
Action/Setting
Description
setup
Setup
Enter Setup menu
Input
Input
Enter Input selection
menu
nmA
4-20 mA
Set meter for 4-20 mA
input
volt
0-10 VDC
Set meter for 10 VDC
input
Total
Total
Enable or disable
totalizer features
d-SCAL
Dual-scale
Enter d-SCAL menu and
select Yes for dual- scale
or No for single scale
display
units
Units
Select the display
units/tags
rate
Rate
Select the display units
for rate
total
Total
Select the display units
for total
Gtotal
Grand Total
Select the display units
for grand total
Dec pt
Decimal
point
Set decimal point for rate,
total, grand total
prog
Program
Enter the Program menu
InCAL
Input
Calibration
Enter the Input
Calibration menu
sCalE
Scale
Enter the Scale menu
Cal
Calibrate
Enter the Calibrate menu
Inp 1
Input 1
Calibrate input 1 signal or
program input 1 value
Dis 1
Display 1
Program display 1 value
Inp 2
Input 2
Calibrate input 2 signal or
program input 2 value
(up to 32 points)
Dis 2
Display 2
Program display 2 value
(up to 32 points)
Error
Error
Error, calibration not
successful, check signal
or programmed value
T tb
Total time
base
Program total time base
T CF
Total
conversion
factor
Program total conversion
factor
T rst
Total reset
Program total rest mode:
auto or manual
GT tb
Grand total
time base
Program grand total time
base
Display Functions & Messages
Display
Parameter
Action/Setting
Description
GT CF
Grand total
conversion
factor
Program grand total
conversion factor
GT rst
Grand total
reset
Program grand total rest
mode: auto or manual
Auto
Automatic
Press Enter to set
automatic total reset
T dly
Time delay
Program time delay for
total auto reset
nmAn
Manual
Press Enter to reset total
manually
dsplay
Display
Enter the Display menu
Line 1
Line 1
Press Enter to assign the
Main display parameter
(default: PV or rate)
Line 2
Line 2
Press Enter to assign the
small display parameter
(default: total)
d-Inty
Display
intensity
Set display intensity level
from 1 to 8
RELaY
Relay
Enter the Relay menu
Assign
Assignment
Assign relays to rate,
total, or grand total
Asign1
Assign 1
Relay 1 assignment
totAL
Total
Assign relay to total
G total
Grand total
Assign relay to grand
total
nm bus
Modbus
Select to display Modbus
input or to assign
Modbus input as the
analog output source
rate
Rate
Assign relay to rate
RLY 1
Relay 1
Relay 1 setup
Act 1
Action 1
Set relay 1 action
Auto
Automatic
Set relay for automatic
reset
A-nman
Auto-manual
Set relay for automatic &
manual reset
any time
LatCH
Latching
Set relay for latching
operation (relays
assigned to rate)
Lt-CLr
Latching-
cleared
Set relay for latching
operation with manual
reset only after alarm
condition has cleared
(relays assigned to rate)
Altern
Alternate
Set relay for pump
alternation control (relays
assigned to rate)
Sanmpl
Sampling
Set relay for sampling
operation

PROVU™PD6200 Analog Input Rate/Totalizer
Instruction Manual
20
Display Functions & Messages
Display
Parameter
Action/Setting
Description
OFF
Off
Disable relay and front
panel status LED
(Select Off to enable
Interlock feature)
Set 1
Set 1
Program set point 1
RSt 1
Reset 1
Program reset point 1
RLY 2
Relay 2
Relays 2-8 setup
Note: Relays 5-8 are
shown, only if expansion
relay module is installed.
FaiLSF
Fail-safe
Enter Fail-safe menu
FLS 1
Fail-safe 1
Set relay 1 fail-safe
operation
on
On
Enable fail-safe operation
off
Fail-safe off
Disable fail-safe
operation
DeLAY
Delay
Enter relay Time Delay
menu
DLY 1
Delay 1
Enter relay 1 time delay
setup
On 1
On
Set relay 1 On time delay
OFF 1
Off
Set relay 1 Off time delay
break
Loop break
Set relay condition if loop
break detected
(For mA input only)
iGnorE
Ignore
Ignore loop break
condition
(Processed as a low
signal condition)
On
On
Relay goes to alarm
condition when loop
break is detected
OFF
Off
Relay goes to non-alarm
condition when loop
break is detected
Aout
Analog
output
Enter the Analog output
scaling menu
Dis 1
Display 1
Program display 1 value
Out 1
Output 1
Program output 1 value
(e.g. 4.000 mA)
Dis 2
Display 2
Program display 2 value
Out 2
Output 2
Program output 2 value
(e.g. 20.000 mA)
reset
Reset
Press Enter to access the
Reset menu
Rst Gt
Reset
grand total
Press Enter to reset
grand total
Rst Hi
Reset high
Press Enter to reset max
display
Rst Lo
Reset low
Press Enter to reset min
display
Rst HL
Reset
high & low
Press Enter to reset max
& min displays
Rst t
Reset total
Press Enter to reset total
Display Functions & Messages
Display
Parameter
Action/Setting
Description
Rst tr
Reset tare
Reset tare (Used when
Total is no only)
Contrl
Control
Enter Control menu
Auto
Automatic
Press Enter to set relays
and analog output for
automatic operation
nmAn
Manual
Press Enter to manually
control relays or analog
output operation
pass
Password
Enter the Password
menu
Pass 1
Password 1
Set or enter Password 1
Pass 2
Password 2
Set or enter Password 2
Pass 3
Password 3
Set or enter Password 3
Total
Total
password
Set or enter password for
manual reset
Gtotal
Grand total
password
Set or enter password for
manual reset
nonrst
Non-
resettable
Non-resettable grand
total set after entering
“050873” for Gtotal
password
unloc
Unlocked
Program password to
lock meter
locd
Locked
Enter password to unlock
meter
999999
-99999
Flashing
display
Overrange condition
Underrange condition