Premier Mounts Rotary series User manual

Installation InstructionsInstallation InstructionsInstallation InstructionsInstallation Instructions
Rotary Tilt Mount
Model: RTM-S
NORTH AMERICA
3130 East Miraloma Avenue
Anaheim, CA 92806 USA
USA and Canada -
Phone: [phone]
Fax: [phone]
EUROPE
Swallow House,
Shilton Industrial Estate,
Shilton, Coventry, England CV79JY
Phone: [phone]
Fax: [phone]
Other Locations - Phone: [phone]; Fax: [phone]
©Premier Mounts 2008
9531-009-021-01
AUSTRALIA, NEW ZEALAND,
OCEANIA (Distributor)
P.O. Box 295
Mordialloc Victoria 3195
Australia
Phone: [phone]
www.premiermounts.com.au

RTM-S
Page 4 Installation Instructions
Parts List
NOTE:This mount is shipped with all installation hardware and components. Make sure that none of
these parts are missing and/ or damaged before beginning installation. If there are parts missing
and/or damaged, please stop and contact Premier Mounts [phone].
Installation Tools
Phillips Head Screw Driver Soft Material/ Blanket Pencil
Tape Measure Thread Depth Indicator (Supplied) Level (Supplied)
5/32" Allen Wrench (Supplied)
Rotating Tilt
Mount (Qty 1)
Universal
Mounting Brackets
(Qty 2)
Hand Crank (Qty 1)
M6 Knurl Knob
(Qty 1)
Griplate™ (Qty 8)
* Parts List continued on next page.

Installation Instructions Page 5
RTM-S
(Qty8)
M6x 20
(Qty8)
(Qty4)
(Qty8)
(Qty8)
(Qty8)
(Qty8)
M6x 30
M6x 45
(Qty8)
M8x 25
M8x 20
(Qty8)
(Qty8)
(Qty8)
(Qty8)
(Qty8)
M8 x 35
M8 x 30
(Qty8)
M8 x 70
M8x 45 (Qty8)
M4 x16
M4 x25
M5 x12
M5 x 20
M5 x 25
M5 x 16
M5x 50
M6 x16
(Qty8)
(Qty8)
Parts List (Cont.)

Page 6 Installation Instructions
RTM-S
Parts List (Cont.)
Nylon spacers and flat washers
NOTE:The nylon spacers may be stacked to achieve proper spacing.
5/16" Flat washers
(metal)
1/4" Nylon spacers 1" Nylon spacers
(Qty 8)
(small) (Qty 8)
(Qty 8)
1/2" Nylon spacers 1/4" Nylon spacers
(Qty 12)
(large)
(Qty 8)
(large)
(Qty 8)
Nylon sleeves 9/16" Nylon spacers
(Qty 8)

RTM-S
Installation Instructions Page 7
Thread Depth Indicator
1. Insert the thread depth indicator (supplied) through the thread inserts found on the back of the flat panel
to make sure the inserts measure the same full depth and mark it (Figure 1).
2. Locate the correct diameter screw for the thread insert. Compare your marking to the screws (supplied).
3. The screw length must not bypass the marking. Select another screw size (Figure 2 and 3), until you find
one that comes closest to your mark without going past.
4. If your selected screw is longer than the marking on the thread depth indicator, DO NOT USE this screw.
Inverted Flat Panel
Display
Marking the Depth
Thread
Depth
Indicator
Threaded Insert
Figure 1
Screw Thread Depth
Indicator
Marking
Screw
Thread Depth
Indicator
Marking
Figure 2 Figure 3

RTM-S
Page 8 Installation Instructions
NOTE:The installation instructions that are contained in this manual refer only to the RTM-S. The
installation instructions for the various bases that are used with the RTM-S will be included with
those products.
NOTE:Prior to installing the RTM-S, the mounting configuration must already be assembled (base,
support poles, etc.).
Mount Installation
Set Screws
1. Slide the mounting block
over and down the support
poles.
2. To secure the mounting block to the support
poles, tighten the four set screws (located on
each side of the mounting block), using the
5/32" Allen wrench (supplied).
Mounting
Block
Cradle
Support
Poles

RTM-S
Installation Instructions Page 9
Universal Mounting Bracket Assembly
1. Place the universal bracket bar and the universal brackets on a flat surface.
2. Slide the universal brackets onto the universal bracket bar (as shown below) with the set screws facing
up. At this time, do not tighten the set screws that are located on the universal bracket.
3. Place the display on a soft, flat surface, face-down. Next, place the universal bracket assembly on the
back of the display, with the universal brackets resting directly over the display mounting points.
4. Once the desired position has been determined, place the Griplate™ washers over each mounting point
and secure them using the appropriate hardware (see Page 5).
NOTE:For the two upper mounting points, the Griplate™ flat side must be facing up. For the two
lower mounting points, the Griplate™ flat side must be facing down.
5. At this time, center the universal bracket bar and tighten the set screws that are located on the universal
brackets.
M4 M5 M6 M8
WARNING: THE CONGFIGURATION THATTHE UNIVERSAL MOUNTING BRACKETS
ARE IN ABOVE MUST REMAIN THE SAME. ANY DEVIATION FROM THE
LAYOUT ABOVE COULD AFFECT THE OPERATION OF THE MOUNT.
WARNING:IT WILL TAKE TWO PEOPLE TO COMPLETE THE NEXT INSTALLATION
STEP.
Griplate™
Universal
Bracket Bar
Set Screw
Universal Mounting Brackets
Griplate™
Griplate™

RTM-S
Page 10 Installation Instructions
6. Lower the universal bracket bar and display into the
cradle (as shown to the left).
NOTE:The circular portion of the universal bracket bar
must rest inside the nylon sleeve. If seated
improperly, the operation of the RTM-S will be
hindered and the nylon sleeve will become
damaged.
7. Insert an M6 knurl knob into the knurl knob mounting
point and tighten.
8. OPTIONAL - Insert a M6 x 12mm security screw and
M6 lock washer into the mounting point and tighten
using the M5 Allen wrench (supplied).
9. OPTIONAL - Tighten the two (2) Phillips head
screws (located on the side of the mounting block)
to prevent the mount from rotating.
Locking Screws
Knurl Knob Mounting Points (a knurl knob may be
placed in either mounting hole).
Nylon
Sleeve
M6 x 12mm Security Head and M6 Lock Washer
Mounting Points (a security screw may be placed in
either mounting hole).

RTM-S
Installation Instructions Page 11
Display Orientation
The RTM-S will allow the user to adjust the display a full 360°.
WARNING:BEFORE ROTATING THE RTM-S, MAKE SURE THATTHE M6 KNURL
KNOB IS SECURELY FASTENED TO THE RTM-S. ALSO, PLEASE MAKE
SURE YOU ALLOW ENOUGH CABLE AND WIRE CLEARANCE FOR FULL
ROTATION.
1. To adjust the RTM-S, rotate the
display either clockwise or
counter-clockwise. 2. Tighten the two
Phillips head locking
screws (see Step 5,
Page 10).
Tilt Positioning
The RTM-S has the ability to tilt
35° up.
Rotate the crank handle to tilt the
RTM-S:
Down - Clockwise
Up - Counter-Clockwise
The RTM-S has the ability to tilt 10°
down.
1. Once the position has been locked down, use an Allen wrench to take off the crank handle.
2. Once the crank handle has been removed, re-attach the crank handle, facing the opposite direction. This
is the storage position for the handle.
M6 Knurl Knob
Crank Handle Storage Position

RTM-S
Page 12 Installation Instructions
Optional Configurations
Technical Specifications
All measurements are in inches (mm).
PSD-TS PSD-BW PSD-EB

RTM-SAddendum
Installation Instructions
RTM-S ADDENDUM:
The RTM-S is shipped with the hand crank in the storage position. The hand crank must be removed
in order for the RTM-S to be adjusted. After theadjustments have been made, return the hand crank
to the storage position. If the hand crank is not returned to the storage position, it may cause damage
to the unit or other equipment. Please return the hand crank to the storage position after operation.
Hand Crank
(Qty 1) 5/32”Allen Wrench (Qty 1)
Storage Position
Loosen the M8 set screw using the 5/32”
Allen wrench. Remove thehand crank.
Operating Position
Once the hand crank has been removed, turn the hand crank
around so that the hand crank knob is pointing away from the
unit. Place the hand crank back onto the unit and tighten the
set screw with the 5/32” Allen wrench.
Storage Position
Slide the hand crank back onto the RTM-S
and tighten the set screw using the 5/32”
Allenwrench.
Hand Crank
Knob
Hand Crank
Set Screw
5/32” Allen Wrench
Page - 14 -