Premier Mounts FTP-096 User manual

Installation Instructions Visit the Premier Mounts website at http://www.mounts.com Page 1
Step 2
FTP-096 / PDS-096 Projector Bracket Installation Instructions
9530-000-961-00
3130 East Miraloma Avenue, Anaheim, CA 92806 USA
USA and Canada
Phone: [phone] Fax: [phone]
[email protected]
Parts List
FTP-096 / PDS-096 Projector Bracket
 Invert the projector and place it on a soft, at surface.
® Remove any foot levelers that might prevent bracket installation.
¯ Locate the mounting points on the projector.
° Place the bracket on the projector.
± Align the mount holes on the bracket with the mounting points on the
projector.
 Insert one (1) M8 x 10mm pan Phillips screw or one (1) M8 x 10mm Lock-
It™ security screw into each mounting point.
® Tighten the mounting hardware.
Do not overtighten the mounting screws.
Step 1
FTP-096 / PDS-096
Bracket (Qty 1)
M8 x 10mm
Pan Phillips Screw
(Qty 6)
M8 x 10mm Lock-It™
Security Screw
(Qty 6)
Your Premier Mounts bracket comes with the option of using
Lock-It™ Security Screws. Simply replace any of the Phillips
head screws with the corresponding sized Lock-It™ Security
screws and tighten using the appropriate Security Allen
wrench.
When you see these graphics associated with a step, you have the option of
using the standard mounting hardware or the Lock-It™ Security hardware.
Lock-It™ Security Hardware Pack
Projector shown is for example purposes only.
Images not to scale.
Which base are you attaching to your projector bracket?
• PDS - Proceed to the “PDS Base Box Installation” section.
• FTP - Proceed to the “FTP Quick Set Base Installation” section.
Step 3

Page 2 Visit the Premier Mounts website at http://www.mounts.com Installation Instructions
Step 5
Step 4
FTP-096 / PDS-096 Projector Bracket
PDS Base Box Installation
Step 5
FTP Quick Set Base Installation
Step 4
 Install the FTP Dome onto your ceiling or 1½” NPT pipe according to the
Fine-Tune Projector Mount installation instructions.
® Slide the Quick Set Base onto the projector bracket and hook the Projector
Plate over the Quick Set Base hinge pins, as shown.
 Insert one (1) M6 x 12mm screw into each of the indicated locations
(supplied with the Quick Set Base).
You can use either the standard hardware or Lock-It™ security hardware.
® Follow the FTP Installation Instructions to complete the installation.
 Insert the four (4) M6 x 12mm tilt adjustment screws, two (2) per side
(supplied with the PDS Base Box).
You can use either the standard hardware or Lock-It™ security hardware.
® Tighten all screws.
Do not overtighten the mounting screws.
¯ Follow the PDS Installation Instructions to complete the installation.
 Place one (1) nylon washer and one (1) ¼″ at washer over the hinge pin.
® Insert and tighten one (1) M6 x 12mm screw (supplied with the PDS Base
Box).
¯ Repeat  and ® for the opposite hinge pin.
You can use either the standard hardware or Lock-It™ security hardware.
Replace eight (8) M6 x 12mm screws and one (1) M6 x 8mm set screw
(supplied with the PDS base box).
Do not overtighten the M6 x 12mm screws or the M6 x 8mm set screw.
° Install the PDS Base Box onto your ceiling or 1½” NPT pipe as per the PDS
installation instructions.
± Slide the projector / Projector Plate assembly onto the PDS Base Box.
² Hook the Projector Plate over the hinge pins, as shown.