Premier Mounts RTM-S User manual

RTM-S
Installation Guide
premiermounts.com | p. 800.368.9700 | e. [email protected]
500 W Central Ave, Suite A, Brea, CA 92821 USA

Installation Guide
RTM-S
Page 2
PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS MUST BE READ AND
COMPLETELY UNDERSTOOD. KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION
FOR FUTURE REFERENCE.
PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS
PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY
UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS,
DEMANDS, SUITS, ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR
IN ANY MANNER RELATING TO ANY SUCH USE, ATTACHMENTS OR MODIFICATIONS.
Warning Statements
Weight Limit
Maximum Flat Panel Weight: 125 lbs.
THE SURFACE MUST BE CAPABLE OF SUPPORTING AT LEAST FOUR TIMES THE WEIGHT OF THE DISPLAY. IF NOT, THE
SURFACE STRUCTURE MUST BE REINFORCED. THE MAXIMUM WEIGHT THAT CAN BE USED WITH THIS PRODUCT IS 160
LBS. PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN, AS OUTLINED IN THE INSTALLATION
INSTRUCTIONS, MUST BE ADHERED TO. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY, OR EVEN
DEATH.
SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT. USE PROPER
SAFETY GEAR AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY.
the display.
If mounting to studs, make sure that the mounting screws are anchored into the center of the studs. Use of an edge-to-edge stud
Be aware of the mounting environment. If drilling and/or cutting into the mounting surface, always make sure that there are no electrical
wires in wall. Cutting/drilling into an electrical line may cause serious injury.
Make sure there are no water lines inside the wall where the mount is to be located. Cutting/drilling into a water line may cause severe
water damage to the mounting surface.
This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.
Do not install near sources of high heat. Do not install on a structure that is prone to vibration, movement or chance of impact.
premiermounts.com | p. 800.368.9700 | e. [email protected]

Installation Guide
RTM-S
Page 3
Included Components:
Mounting
Block (Qty.1)
M5 Security Allen
Key (Qty.1)
M6 x 30mm Screw
(Qty.4)
M8 x 16mm Screw
(Qty.4)
M8 x 25mm Screw
(Qty.4)
M8 x 30mm Screw
(Qty.4)
M4 x 25mm Screw
(Qty.4)
M4 x 30mm Screw
(Qty.4)
M6 x 16mm Screw
(Qty.4)
M6 x 25mm Screw
(Qty.4)
Universal Spacer
(Qty.8)
M6 x 12mm Button
Security (Qty.1)
M6 Lock Washer
(Qty.1)
M10 x 30mm Screw
(Qty.4)
M4 x 16mm Screw
(Qty.4)
Griplate™(Qty.4) Straw (Qty.1) 5/32" Allen Key
(Qty.1)
12
Remove the M6 Knurl Knob from the mounting
block and place it aside.
Slide the mounting block over the tubes.
Rotational Stop
(Qty:1)
M6 x 25mm
Flat Screw (Qty.3)
Cross Bar (Qty.1)
Mounting Bracket (1 Pair)
premiermounts.com | p. 800.368.9700 | e. [email protected]

Installation Guide
RTM-S
Page 4
4
3
Tighten the four (4) pre-installed M8 set screws using the
supplied 5/32" Allen Key.
Small Straw or Toothpick
Marking the 1/8”
Allowance
Small Straw
or Toothpick
Small Straw
or Toothpick Depth Plus 1/8” Allowance
Mark
Depth Plus 1/8” Allowance
Mark
1) Insert a small straw or toothpick into the threaded inserts found on the
2) Use a pencil to mark the depth of the threaded insert on the small straw
or toothpick.
3) Mark the straw or toothpick 1/8” above the depth of the threaded insert,
as shown in Figure 1.
4) Insert the small straw or toothpick into the remaining threaded inserts
to compare and verify their depth using the straw or toothpick’s 1/8”
allowance mark.
5) Locate the correct diameter screw for the threaded insert.
If the screw you selected is longer than the 1/8” allowance mark on
the small straw or toothpick, as shown in Figure 2 and Figure 3, do
not use this screw. The screw length must not bypass the mark.
6) Test each size of the screws provided.
The correct screws should thread easily into themounting point and
not pull out when tension is applied.
Selecting the Mounting Hardware
premiermounts.com | p. 800.368.9700 | e. [email protected]

Installation Guide
RTM-S
Page 5
7
7
5
6
Slide the mounting brackets into the cross bar.
Bottom
Top
Align the brackets to the display mounting holes. Use the depth measuring straw to determine the ap-
propriate hardware. Use four (4) M4, M6, or M8 screws depending on display and four (4) Griplate™
(Universal Washer). Use Universal Spacer if necessary.
M4, M6, or M8 screws
Griplate™ (Universal Washer)
Universal Spacer (Optional)
Top
Bottom
premiermounts.com | p. 800.368.9700 | e. [email protected]

Installation Guide
RTM-S
Page 6
7
8
1. Install the Rotational Stop with (3) M6 x 25mm Flat Head Screw.
2. Reversible in either left or right orientation.
M6 x 25mm Flat
Head
Rotational Stop
M8 x 10mm Set Screw
C
L
Center the cross bar to the display and tighten the two (2) M8 x 10 Set Screws using the
5/32" Allen Key to secure the brackets.
premiermounts.com | p. 800.368.9700 | e. [email protected]

Installation Guide
RTM-S
Page 7
9
10
Install the M6 Knurl Knob removed from step 1 to secure the cross bar from dislodging.
Two persons are recommended for this step. Lift the display bar and place the disk it into the
receiver plate.
premiermounts.com | p. 800.368.9700 | e. [email protected]

Installation Guide
RTM-S
Page 8
12
Tension
Screw
is attained.
M4 x 8mm Set
Screw
Adjust the level of the display arms by loosen/tighten (2) M4 x 8mm Set Screw.
Level
Level
11
premiermounts.com | p. 800.368.9700 | e. [email protected]

Premier Mounts intends to make this manual accurate and complete. However, Premier Mounts makes no claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this
document is subject to change without notice or obligation of any kind. Premier Mounts makes no representation of warranty, expressed or implied, regarding the
information contained herein. Premier Mounts assumes no responsibility for accuracy
PREMIER MOUNTS
LIMITED LIFETIME WARRANTY
What and Who is Covered by this Limited Lifetime Warranty
Premier Mounts warrants all mounting products to be free from defects in material and workmanship for the
lifetime of the original installation of the product.
What Premier Mounts Will Do
At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is
defective. If Premier Mounts chooses to replace a defective product or part, a replacement product or part will
be shipped to you at no charge, but you must pay any related labor costs.
What is Not Covered: Limitations
Premier Mounts disclaims any liability for damage to mounts, adapters, displays, projectors, other property,
products.
NOTWITHSTANDING ANYTHING TO THE CONTRARY IN THIS WARRANTY, THIS WARRANTY IS
LIMITED TO FIVE YEARS FROM THE DATE OF PURCHASE IN THE EVENT THAT THE WARRANT-
ED PRODUCT IS COMMERCIALLY RENTED OUT.
electrical items, are backed by a 3-year warranty.
Premier Mounts disclaims all other warranties, express or implied, including warranties of merchantability and
including but not limited to, inability to use its products or labor costs for removing and replacing defective
products or parts. Some states do not allow the exclusion or limitation of incidental or consequential damages,
so the above limitation or exclusion may not apply to you.
What Customers Must Do for Warranty Service
If you discover a problem that you think may be covered by the warranty, you must report it in writing to the
address below within thirty (30) days. Proof of purchase (an original sales receipt) from the original consumer
purchaser must accompany all warranty claims. Warranty claims must also include a description of the problem,
the purchaser’s name, address, and telephone number. General inquiries can be addressed to Premier Mounts
Customer Service at 1-800-368-9700. Warranty claims will not be accepted over the phone or by fax.
How State Law Applies
PREMIER MOUNTS
ATTN: Warrenty Claims
500 W Central Ave, Suite A
Brea, CA 92821
PREMIER MOUNTS
500 W Central Ave, Suite A
Brea, CA 92821
USA & CANADA
Phone: [phone]
Fax: [phone]
©
e. [email protected]