Premier 8016/429 User manual

4. DO NOT OPERATE THE TOOL NEAR A FLAMMABLE SUBSTANCE.
Never operate the tool near a flammable substance
(e.g., thinner, gasoline, etc). Volatile fumes from these substances could be
drawn into the compressor and compressed together with the air and this
could result in an explosion.
5. DO NOT USE A WRONG FITTING.
The connector on the tool must not hold pressure when air supply is
disconnected. If a wrong fitting is used, the tool can remain charged with air
after disconnecting and thus will be able to drive a fastener even after the
air line is disconnected, possibly causing injury.
6. DO NOT TOUCH THE TRIGGER UNLESS YOUR INTEND TO
DRIVER A FASTENER.
Whenever the air supply is connected to the tool, never touch the trigger
unless you intend to drive a fastener into the work. It is dangerous to walk
around carrying the tool with the trigger pulled, and this and similar actions
should be avoided.
7. NEVER POINT THE DISCHARGE OUTLET TOWARD YOURSELF
AND PERSONNEL.
If the discharge outlet is pointed toward people, serious accidents may be
caused when misfiring. Be sure the discharge outlet is not pointed toward
people when connectingand disconnecting the hose. Loading and not loading
the fasteners or similar operations.
8. KEEP HANDS AND BODY AWAY FROM THE DISCHARGE OUTLET
When loading and using the tool, never place a hand or any part of body in
fastener discharge area of the tool. It is very dangerous to hit the hands or
body by mistake.
Staple Specification
WARNING: Be sure to use only the genuine nails recommended for the
this nailer. The use of any other nails can result in tool malfunction, leading
to serious injuries.

Parts list and Schematic
NO. CODE NO. CODE Description
1511120 O-RING 2.5X1.8 27 322700 LOCK PAWL
2511100 O-RING 12.2X1.75 28 421510 COVER
3511060 O-RING 15.5X1.75 29 322660 BACK COVER
4511110 O-RING 16.4X1.8 30 410620 BUMPER
5511080 O-RING 16X1.25 31 110490 BODY
6511090 O-RING 8X2.6 32 322720 SILENCER
7511140 O-RING 25X2.65 33 410660 DAMPER
8511050 O-RING 27.5X2.6 34 421450 VALVE GASKET
9511040 O-RING 31.5X2.65 35 421460 VALVE CAP
10 510390 O-RING 17X2.65 36 421470 TRIGGER
11 322830 PIN 37 310450 VALVE CYLINDER
12 640290 STRAIGHT PIN 3X24 38 421440 VALVE SHAFT
13 640310 STRAIGHT PIN 4X19.5 39 410640 INTERMEDIATE VALVE
14 630300 WASHER 40 322910 CYLINDER CAP
15 610490 BOLT M4X12 41 310540 CYLINDER
16 610500 BOLT M4X16 42 322920 BACK NOSE ASSEMBLY
17 610720 BOLT M4X14 43 310550 COVER
18 310470 END CAP 44 210880 FRONT COVER
19 621030 TENSION SPRING 45 322930 DRIVER BLADE
20 511130 O-RING 19.5X3 46 322750 PULLEY
21 322690 FEED BAR 47 322670 PIN
22 421430 PISTON 48 421490 STOP
23 421480 VALVE PIN 49 640170 ROLL PIN 3X28
24 421500 END PIECE 50 410630 RUBBER HANDLE
25 421520 COVER 51 640320 STRAIGHT PIN B4X29
26 621040 LEG SPRING P1. D322931 DRIVER UNIT
Description

Maintenance and Inspection
Read the section title SAFETY.
SERVICE AND REPAIRES
All quality tools will eventually require servicing or replacement of parts due
to wear from normal use. It is recommended that these operations should be
performed by a professional technician.
NOTE:The information contained in this Manual is designed to assist you in
the safe maintenance of the nailer.Some illustrations in this Manual may show
details or attachments that are different from those on your nailer.
WARNING: Disconnect air hose and remove nails from nailer when:
●
Doing maintenance and inspection
●
Cleaning a jam
Inspecting the magazine
1. DISCONNECT AIR HOSE.
2. Clean the magazine. Remove dust which may have accumulated in
the magazine.
3. Lubricate the nailer rail with nailer lubricant.
Clearing a jam
Remove a jammed nail in the following order:
1. DISCONNECT AIR HOSE.
2. Remove all nails.
3. Remove the jammed nail with a slotted head screwdriver.
4. In case of frequent jams, contact an authorized service center.
A qualified person should perform repair and maintenance
Warranty will be honored, only if:
1. Clean, dry, regulated compressed air has been used at
air pressure not exceeding the maximum indicated on
the tool casting;
2. No evidence of abuse, abnormal conditions, accident,
neglect, misuse or improper modifications or stroage
of the prodcut exists;
3. No deviations from following recommended operating
instructions, specifications, and maintenance schedules
exist.(Read Operator Manual for use, specifications and
maintenance instructions).
(April. 2016)
GENERAL WARRANTY CONDITIONS