Premio FlacheSAN1L-D4 User manual

Installation and service of this product should be conducted by a trained
personnel to avoid any bodily injury from electric shock or heavy object hazard
Observe ESD (Electrostatic Discharge) practices during integration to avoid
possible damage to the board and / or other components
FlacheSAN1L-D4 Enclosure Quick Guide
Version 2.80 –2016.03.28
1. Check the content of the box. Please verify that
your package contains the following:
#
Description
Image / Description
Qty
1
1U20 Enclosure,
27” depth
1
2
2.5” Tool-less
Drive Trays
20
3
Motherboard
Asrock EP2C612D16NM series
1
4
Internal SAS
cables
SFF8087-8087 or SFF8087-8643
depending on SKU
5
5
Expander board or
OS disk bracket
Depending on SKU
1
6
CPU and memory
(optional)
Pre-installed upon request
2
sets
7
Heat sink
(optional)
2
8
Screw Sets*
for drives, motherboard, and rail
/ rack
3
sets
9
Power Cable*
2
10
Slide Rail Kit (opt)
1
11
Front Bezel (opt)
12
This Quick Guide
1
13
Packaging
1 set
* Inside the accessories box. If any items are missing, please contact
your authorized reseller or sales representative
2. Get familiar with the unit.
Front View
Power Button / LED:
System Status LED:
NIC LED:
System On
System Off
Reset Button
System Normal
ID Button / LED:
ID On
ID Off
20 Drive Bays
Ear Handle
Link UP /Act
Link Down
1 2
Front Panel
(Blink) System Error e.g. Fan fail
Rear View
PCIe Gen3
x16 Slot
Power
Supply B
Power
Supply A
IPMI
LAN Port
COM
Port
USB3.0
Ports
VGA
Port
PCIe Gen3
x16 Slot
Serial
Port
1GbE or 10GbE
Ports
Alarm Mute
Button
1 2
10GbE Slot
w/ mezzanine
or
OS Disks
or
Drive Tray
3. Remove the top cover by removing the 8 screws
(red circles) on the top of the unit and slide the cover towards
the back of the unit.
Remove additional 3 screws (blue circles) to open the middle
top cover (for backplane access).
4. Inspect the internal of the chassis. By default, it
consists of an Asrock EP2C612D16NM series Haswell DP
Grantley motherboard, a set of backplanes, blower modules,
PCIe riser cards for IO cards, and an option of an expander
module or a drive bracket depending on the order SKU.
OS Disk Bracket
(optional)
PSU
Asrock
EP2C612D16NM
motherboard
PCIE7 Riser Blower Module x3
Expander Board
(optional)
5 columns of
backplanes
with one SFF-
8087 mini-SAS
connector and
4 SATA drive
slots each
OS Disk Bracket
(optional)
Mezzannine
Slot (optional)
PCIE6 Riser
See illustration below for the data path from disk devices to
the host. Two options are available: through an expander (red
path), and with no expander (purple path).
For expander mode, a set of SAS cables are routed from
backplanes to expander board and then a choice of routing to
an IO card or an on-board SCU port (SAS2/SATA3 6Gb/s).
For OS, in place of one PCIE6 card, OS disk bracket is used.
IO Card
IO Card with
5 SAS ports
5 SAS DOWN
Ports
SAS UP
Port(s)
5 SFF 8087-
8087 SAS
cables
1 SFF 8643 to
8643 or 8087
SAS cable
LSI3008
Ports
5 SFF 8087-
8643 SAS
cables
OR
For a non-expander SKU, in place of expander board, an OS
disk bracket occupies the space. Due to an absence of the
expander board, to access all 20 drives from the front bay, an
IO card with five SAS ports is required, e.g. Adaptec 72405.
Thank you for your purchase of FlacheSAN1L-D3 1U 20-Bay Haswell Dual-Processor Storage Server!
2.5" 7mm
HDD / SSD
Tray
Drive Lock
(unlocked position)
Tray Latch
Tray Handle
Drive Status LED:
(Solid) Drive Online
To unlock the drive lock:
1. Push the
drive lock
latch
inwards
2. Then pull
it upwards (Blink) Drive Activity
(Fast Blink) Drive Locate
(Slow Blink) Rebuild
(Solid) Drive Fail
Tool-less drive tray is best used for SSDs.
It is recommended to apply M3 screws when installing HDDs

FlacheSAN1L-D4 Quick Guide
For more information please visit our website at www.premioinc.com
Copyright © 2016, Premio Inc. All rights reserved.
5. Install CPU and memory (may be sold separately)
to their respective slots on the motherboard. Please be aware
of each component’s installation requirements and
prerequisites. Refer to the motherboard’s TPS for details.
- Supports Intel Xeon E5-2600/
4600 & V3 series
- Dual Socket LGA 2011 R3
- 16 DDR4 DIMM slots
- Quad channel memory
- Supports 2133/1866/1600 LR/R/
ECC DIMM and NVDIMM
- 1.2V
- 3 PCIe Gen3 x16 slots
- PCIE6 is routed to CPU1
- PCIE7 and PCIE2 from CPU2
EP2C612D16NM
6. Install OS disk(s) into the bracket. There are two
locations where OS disks can be placed in replacement of:
expander and PCIe card. See below on how to install:
1. Install one or two
disk(s) to the bracket,
secure it with 4 M3
screws each at yellow
circle locations
3. Place the OS disk bracket assembly
back to the enclosure. Secure with
provided screws (red circles)
4. Connect SATA
cables and power
cables to the disk(s)
2a. Make sure
PCIE6 riser card
is removed 2b. Make sure
expander board
is removed
PCIe Location Expander Location
7. Install IO cards (may be sold separately) to PCIe
slots.
A. For PCIE7 slot, remove the thumbscrews
and insert IO card to riser card
B. For PCIE6 slot, remove the bracket 
and insert IO card to riser card
For more IO cards information, refer to the user’s guide for IO
cards. To install mezzanine card, remove PCIE7 riser card first.
8. Replace the top cover. Once we are finished with
the internals of the system, close the top of the chassis as
described below:
2. Slide the cover
forward
3. Secure the cover
with eight 6-32
thread screws
1. Place the top cover to the
chassis using the pin as a guidance
9. Remove drive trays from the enclosure.
1. Push the tray
latch to release
the tray handle
2. Pull the tray
handle to remove
the drive tray out
from the
enclosure bay
10. Install drives into trays. Follow the diagram
closely. SSD and HDD sold separately. For HDD installation,
the use of M3 screws is recommended.
1. Slide in drive with IO
connector side first to the
back of the tray
4. Snap in the
hinge back to
lock position
3. Snug the
other end of
the drive into
the tray
To remove the disk, do the steps in reverse.
Poke from the bottom hole to help lift the disk.
2. Make
sure the
drive goes
underneath
the hooks
11. Place the unit to the rack. Two types of slide
rail (22” and 28” long) are available. Secure with screw as
indicated. Please refer to Rail Kit Installation Guide on how to
mount the enclosure to the rack.
22"
28"
12.Install the populated drive trays into the
enclosure with the drives properly secured to the hard drive
trays.
1. Push the tray by the
latch all the way into the
drive bay to ensure a
complete insertion
2. Secure the drive tray to
the enclosure by placing the
tray handle to lock position
13.Drive mapping begins from top to bottom and to
the right, depending on the cable connection of the expander
/ on-board SATA ports.
1
204
5
14.Plug in the power
cords to the AC receptacles on the
back of the unit and secure it with
the wire lock.
15.Press the power button on the
front of the unit after connecting a monitor
and input devices, and get ready for software
setup.

FlacheSAN1L-D4 Quick Guide
For more information please visit our website at www.premioinc.com
Copyright © 2016, Premio Inc. All rights reserved.
Access the Serial Console (for
expander model) by connecting a serial
cable to the serial port and use a
terminal console with baud rate 38400,
8, N, 1, N. Type “help –a” for a list of
commands.