Premium PRF185MW User manual

1
General
This type of refrigerator is widely used in places
such as hotels, offices, student dormitories and
houses. It is mostly suitable for refrigerating and
preserving foods such as fruits and beverage. It
enjoys the advantages of small size, Lightweight,
Low electric consumption and easy use.
Instructions for Installation
1 Do not tilt the refrigerator for more than 450
from its vertical position while transporting it.
And do not apply force on any part of the
refrigerator such as the condenser and door to
prevent any type of damage. In addition it will
influence its performance.
2. Let the refrigerator have enough space to work
well.
3. Don’t install it in high temperature of humidity
place so as to avoid being damaged, dampened
and rusted.
Cautions for Safety
1. Before the refrigerator is plugged in check in the
electric voltage to be used fit is the same as the
rated voltage. The power plug should have its
independent socket, adapter may cause the
socket overheat.

2
2. Don’t store inflammable materials such as ether,
benzine, LP gas and glue etc in the refrigerator.
3. Don’t splash water on the refrigerator; it may
arouse malfunction or electric shock.
4. When gas leaks from its container. Don’t pull
the plug out or in. it may arose sparks and fire
calamities.
DANGER or WARNING:
1. Risk of child entrapment. Before you throw
away your old refrigerator or freezer:
-Take off doors.
-Leave the shelves in place so that children may
not easily climb inside.”
2. Do not use extension cords.
Instructions for Use
1. When operating the refrigerator for the first time,
run it without loading any food until it autos
tops at the desired temperature. Usually it takes
2 or 3hours, then set the thermostatic dial at the
setting desired and put foods in the refrigerator.
2. The temperature of the refrigerator can be
adjusted by turning the thermostatic dial. A
medium setting of the thermostatic dial is the
most suitable for general operation. Set the
thermostat at “6” position only when ice cubes

3
are made or frozen food are stored in the
freezing compartment.
3. Defrost the freezing compartment whenever the
layer of frost on the surface of the evaporator
reaches 3 or 4 mm. When defrosting remove all
food and ice cube tray and set the thermostat at
“OFF” position. Put the drip tray under the
evaporator to collect melted water. After the
frost has melted, discard the melted water and
dry up the interior of refrigerator. The
refrigerator can then be restarted by turning its
thermostat to the desired setting.
4. Instruction for making and removing pieces of
ice cube.
Fill water into the ice making case below the
graduated line, put it into the freezing
compartment, and then set the thermostat at “6”
position. It takes about 2 or 3 hours to make ice
cubes. Pieces of ice cube can be removed by
twisting the ice making case. Don’t cut up and
down, otherwise it may be broken.
Cautions for Use
1.The more foods tuff put in or the more and the
longer for once the door is opened, the more it
needs electric consumption, which even leads
malfunction.
2. Better not to place the objects which are too
heavy, pointed or corrosion on table board.

4
3. Re-plugging in the power plug at the interval of
over ten minutes.
4. Don’t store bottled drink in the freezer, so as to
prevent from being broken and damaging the
refrigerator.
5. Open the door as less as possible during
power-cut.
6. When defrosting, never use any sharp or
metallic objects to remove the frost on the
surface of the evaporator as it will damage the
evaporator.
7. Don’t touch foods and containers in the freezing
compartment with your wet hands so as to
prevent from being frostbitten.
Maintenance
1. While cleaning the refrigerator. Pull out the
electric power plug; rub carefully with a piece of
cloth soaked with natural cleanser then wipe
with clean water. The abrasive cleaning power,
alkali cleansers, chemical cloth, thinner, alcohol,
acid petroleum product and hot water are not
suitable for cleaning the refrigerator; they may
damage the painting cover and plastics.
2. The door gasket is dirty and fogged easily, so
clean it frequently.
3. If the refrigerator is out of use for a long time,
please pull out the plug, clean and dry the
freezing compartment then close the door

5
tightly.
The following cases are not malfunction
1. A flowing water sound:
Flowing water sound will be heard under normal
operation.
2. Outside condensation:
Outside condensation is normal in high humidity
condition. You may just wipe it up yourself.
3. It takes some times for the temperature of the
freezer and refrigerator compartments to become
cold after the refrigerator starts to operate: If the
temperature of the two compartments is higher
while the refrigerator is operating, it takes some
time for the temperature of the two
compartments to become cold. If the
environmental temperature is higher, it takes a
long time to make the compartments to become
cold.
4. The surface of the compressor becomes hot:
The surface of the compressor may become hot
under normal operation. Don’t touch it with
hands.
Methods of inspecting malfunction
If any case of malfunction happens, please
inspect and dispel it according to the methods
shown in the following table.

6
case Inspection
Not
refrigerating
Is there no electric current?
Is the voltage normal or not?
Has the socket fused?
Has the plug been put in
effectively?
Not efficient
Is the thermostatic dial set to the
correct position?
Is there any suitable clearance
surrounding the refrigerator?
Has the door been opened too
frequently or too long?
Is the refrigerator exposed to
sunlight directly or placed near
some heating devices.
Are there too much food inside?
Or are too hot?
Food frozen
in the
refrigerator
Compartment
Is the thermostatic dial set to the
correct position?
Have the foods stuff been put too
crowded?
Noises Is the refrigerator installed firmly?
Has the refrigerator been struck by
some other objects?

7
Compressor
Cannot stop
automatically
Are the foods stored too much at
one setting?
Are the doors opened too
frequently or too long?
If the above methods are not yet effective, please
contact with the maintenance service department
for help without any delay.

8