PRESIDENT HR2510 User manual

- 1 -
CHIPSWITCH
OWNERS MANUAL
Revised August 28th, 2000
HR2510 / HR2600 / LINCOLN
10 Meter AmateurTransceiver
http://hr2510.freeservers.com/
DOC’S RADIO REPAIR

- 2 -
Table of Contents
FIRSTTIME INSTALL / POWER UP ...................................................... 3
ENABLE/DISABLEFUNCTIONS .......................................................... 4
PROGRAMMODE ................................................................................. 5
MEMORY CHANNELTEMPORARY LOCKOUT.................................... 6
SCAN LIMITS ON/OFF .......................................................................... 7
SPLIT FREQUENCY OPERATIONS ON/OFF ....................................... 8
OPERATING IN SPLIT FREQUENCY MODE ........................................ 9
SPLIT FREQUENCY POLARITY CHANGE......................................... 10
PRIORITY CHANNEL ON/OFF **REQUIRES ADDITIONAL HARDWARE ................................. 11
PRIORITY CHANNEL CHECK & LOCK .............................................. 12
MASTERRESET ................................................................................. 13
USING SPLIT CHANNEL with PRIORITY CHANNEL FUNCTION ..... 14
OPERATEMODE................................................................................. 15
FREQUENCY BAND (0) ...................................................................... 16
MEMORY GROUP 1 (1) ....................................................................... 16
MEMORY GROUP 2 (2) ...................................................................... 16
MEMORY GROUP 3 (3) ....................................................................... 17
SCAN, CHANNEL UP/DN, AND MIC UP/DN....................................... 17
LOCAL BEEPTONE ............................................................................ 17
PROGRAM MODE ............................................................................... 18
PROGRAMMING ................................................................................. 19
PROGRAMMING (continued) ............................................................. 20
PROGRAMMING (continued) ............................................................. 21
PROGRAMMING (continued) ............................................................. 22
SERIAL NUMBER DISPLAY................................................................ 23
ERROR MESSAGES............................................................................ 24
MANUFACTURER INFORMATION...................................................... 25

- 3 -
FIRSTTIME INSTALL / POWER UP
The first time the HR2510/HR2600/LINCOLN is powered up,
afterthe CHIPSWITCH hasbeeninstalled,you will be required
to enter the type of radio you are using.The radio will display
“HR2510” as the first choice, “HR2600” asthesecond choice
and “LINCOLN” as the third. Press the Span button until the
type of radio you have is displayed on the readout.Then press
the Band button to enter that selection into the
microcomputer’s memory. You are only required to do this
when the CHIPSWITCH is installed into your radio for the first
time, or if you issue a MASTER RESET command.
Note: If your radio is turned off for an extended period of time,
or if a severe electrical disturbance (sparking wires, shorts,
etc.) Is caused on the power supply to the radio, the internal
memory inside the microcomputer chip may ‘forget’ what you
have programmed into it. If this should happen, your radio will
display‘HR2510’and you will need to re-program it just as you
did when the chip was first installed. Also, a severe electrical
disturbance may cause your radio’s memory to become ‘con-
fused’, causing improper frequencies or strange characters to
be displayed on the readout. If this should happen, invoke a
MASTER RESET function and then re-program the radio.

- 4 -
ENABLE/DISABLE FUNCTIONS
While the HR2510 / HR2600 / LINCOLN is in OPERATE
MODE, you can enable or disable any of the radio’s major
functions from the front panel. Some of these functions are not
operational in specific “BANDS.” The display segment before
the frequency readout indicates which function is enabled.
FUNCTION BAND INDICATION KEYS PRESSED
Program Mode En/Disable 0,1,2,3 P (Band pos) F.lock/Meter
(3)
/Chan Up
Memory Chan Temp. Lockout 1,2,3 Top Bar F.lock/Span/Chan DN
Scan Limits ON/OFF 0 Bottom Bar F.lock/Band/Span
Split Freq. OPNS. ON/OFF 0 H/L F.lock/Band/Chan DN
Split Freq OFFSET change
(1)
0 H/L F.lock/Scan/Chan UP
Priority Channel ON/OFF
(2)
0,1,2,3 Flashing Band F.lock/Scan/Chan UP
Go to PRIORITY CHANNEL 0,1,2,3 P F.lock/Scan/Meter
(3)
MASTER RESET 0,1,2,3 Hr2510 F.lock/Scan/Meter
(3)
/Pwr ON
NOTE:
(1)This function will only work if PRIORITY CHANNEL frequency is not programmed.
(2)This function will only work if PRIORITY CHANNEL frequency is programmed.
(3) On the LINCOLN radio, use INDICATOR instead of METER

- 5 -
PROGRAM MODE
This function enables you to program the new CHIPSWITCH
features on the HR2510 / HR2600 / LINCOLN.
Step 1. Press the F.lock button in.
Step 2. Press the Meter (INDICATOR for the LINCOLN)
and Channel up buttons simultaneously
The radio notifies you that you are in PROGRAM MODE with
“ 4 beeps”, and a“P”is displayed in the Band indicator. At this
point, you are able to program any of the 46 FEATURES
outlined in the PROGRAMMING section of this manual.