Prima A4 User manual

OPERATING MANUAL
A4 HEAT PRESS
Contents:
1. Assembly drawing
2. Technical Specications
3. Operating Process
Page 2
Page 3
Page 4 -6
Warehouse 3, Browns of Carlisle, Carlisle, Cumbria, CA5 6LF www.primaheatpresses.com [phone] VAT No. GB944407715

1 - Assembly Drawing
1
2
3
4
5
7
6
1. Control Box
2. Control Panel
3. Pressure Adjustment Knob
4. Operating Handle
5. Stabilising Feet
6. Heat Pattern (21cm x 29.5cm)
7. Lower Platen (Unheated)
When the press is removed from the box the Stabilising feet (5)
may be disassembled for shipping. Please screw the feet into the
threaded holes on the legs of the press before operang the press.
ATTENTION!
Warehouse 3, Browns of Carlisle, Carlisle, Cumbria, CA5 6LF www.primaheatpresses.com [phone] VAT No. GB944407715

2 - Technical Specications
42.9cm
34cm
32.9cm
Power consumption 1 kW
Voltage 230 V
Heat platen size 21 cm x 29.7 cm
Printable articles maximum size 21 cm x 33 cm
Time settings 0 - 999 sec
Maximum temperature 225°C
Machine dimensions 34 cm (w) x 42.9 cm (d) x 30.2 cm (h)
Gross Weight 17.2 Kg
Technical Specication
Dimensions
Warehouse 3, Browns of Carlisle, Carlisle, Cumbria, CA5 6LF www.primaheatpresses.com [phone] VAT No. GB944407715

3 - Operating Instructions
3.1 Introduction to the control panel
3.2 Power ON the heat press
1. Temperature Option Selection
2. SETIEM LED (illuminated when the
temperature is being set)
3. Temperature SET Button
4. Temperature Display
5. OUT LED (illuminated when the
heat element is on)
6. Temperature DOWN Button
7. Temperature OUT Button
8. AT/ALM LED (illuminated when the
press is in operaon and the mer is counng)
9.Time DOWN Button
10. Time UP Button
11SETTIM LED (illuminated when the
me is being set)
12. Time SET Button
Power Button
Below is a diagram of the control panel of your heat press, from here you will control all the
functions of your press.
14
5
6
7
7
8
9
10
11
12
2
3SET
SET
Temperature
Time
C
F
S
SETTEM
SETITM
NTIF - 2000
AT/ALM
OUT
8888
8888
i
When the press is powered on the power switch on the
side of the machine will be illuminated and the control
panel will power on.
The heang element will begin to heat up immediately.
INFORMATION!
1. Connect your heat press to mains power using the power cable provided.
2. The press can now be turned on using the main power
button located on the side of the press.
Warehouse 3, Browns of Carlisle, Carlisle, Cumbria, CA5 6LF www.primaheatpresses.com [phone] VAT No. GB944407715

3- Operating Instructions
3.3 Setting the pressing parameters
3.3 Setting the pressing time
1. To set the power press the Temperature SET Button (3) the SETTEM LCD will light up.
2. You can then use then use the Temperature UP (7) and Temperature DOWN (6) arrow to
set the desired Temperature.
1. To set the power press the Temperature SET Button (12) the SETTEM LCD will light up.
2. You can then use then use the Temperature UP (10) and Temperature DOWN (9) arrow to
set the desired Temperature.
3. Once the desired temperature has been set
press the Temperature SET button (3) again to
conrm the setting.
3. Once the desired temperature has been set
press the Time SET button (12) again to
conrm the setting.
14
5
6
7
2
3SET
SET
Temperature
Time
C
F
S
SETTEM
SETITM
NTIF - 2000
AT/ALM
OUT
8888
8888
i
i
Once the temperature has been set the heat
platen will begin to climb to the desired tem-
perature. This may take a few minutes as the
element heats up. An alarm will sound once
the desired temperature is reached. To stop the
alarm close and then open the press.
Once set the mer will begin to count down
when the heat press is closed. An alarm will
sound when the press cycle is complete
indicang when to open the press again
INFORMATION!
INFORMATION!
7
8
9
10
11
12
SET
SET
Temperature
Time
C
F
S
SETTEM
SETITM
NTIF - 2000
AT/ALM
OUT
8888
8888
Warehouse 3, Browns of Carlisle, Carlisle, Cumbria, CA5 6LF www.primaheatpresses.com [phone] VAT No. GB944407715

3 - Operating Instructions
3.4 Setting the pressure
Clockwise will increase the
pressure
Anti-Clockwise will
decrease the pressure
1. Before adjusting the pressure knob (3) ensure
that the press is in the open position.
2. With the press open turn the pressure knob
(3) to adjust the pressure, clockwise increases
the pressure and counter-clockwise will lower
the pressure.
It is important that you change the force that is applied by the press to suit the substrate that is
being used. Follow the steps below to adjust the pressure.
If you have any further questions about the operation of your heat
press please do not hesitate to contact our Tech Support Team
using the details below
[phone]
[email protected]
3
Warehouse 3, Browns of Carlisle, Carlisle, Cumbria, CA5 6LF www.primaheatpresses.com [phone] VAT No. GB944407715