Prime Design VBR 326 User manual

PRIME DESIGN, A SAFE FLEET BRAND 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪ Phone: [phone] ▪ 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email:[email protected] ▪ www.primedesign.net
TM & © 2015 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6092974, 6764268, 6971563, 2364879, 8857689, 8511525, 8991889 AND OTHER PATENTS PENDING
2
1
3
5
4
2
8
7
6
10
10
10
9
9
9
11
VBR-326 ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS
CONTENTS OVERVIEW
1—Rear Crossbar................................................... (Qty 1)
3—Front Crossbar.................................................. (Qty 1)
6—Front Drive Shaft .............................................. (Qty 1)
B Version, 35.75”
4—Rear Drive Shaft............................................... (Qty 1)
Right Hand, B4 Version, 50.00”
5—Connecting Bar................................................. (Qty 1)
48.00”
2—Center Crossbar ............................................... (Qty 1)

PRIME DESIGN, A SAFE FLEET BRAND 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪ Phone: [phone] ▪ 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email:[email protected] ▪ www.primedesign.net
TM & © 2015 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6092974, 6764268, 6971563, 2364879, 8857689, 8511525, 8991889 AND OTHER PATENTS PENDING
3
VBR-326 ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS
7—Z Post ................................................................ (Qty 2)
Adjustable, 7.25”
8—L Post ................................................................ (Qty 2)
Top Mount, 9.25”
9—Mounting Bracket Assembly.............................(Qty 3)
Vertical, Low Mounting, 4.50”, GM
10—Mounting Bracket Assembly...........................(Qty 3)
Horizontal, Low Mounting, 4.50”, GM
11—Ladder Stop.....................................................(Qty 3)
With Hardware
HKT-8140-Rotation Hardware Kit
ASZ-0101 (1X)
LUB-0101 (1X)
CLP-1100-F (1X)
CTP-1075-B (1X)
BLT-6850-M8 (4X) BLT-6822-H (2X)
LBL-0105 (8X)
BLT-6870-M8 (6X)

PRIME DESIGN, A SAFE FLEET BRAND 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪ Phone: [phone] ▪ 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email:[email protected] ▪ www.primedesign.net
TM & © 2015 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6092974, 6764268, 6971563, 2364879, 8857689, 8511525, 8991889 AND OTHER PATENTS PENDING
4
Insert 45MM carriage
bolt through mounting
brace, bracket, and
Z Plate as shown.
VBR-326 ASSEMBLY INSTRUCTIONS–HORIZONTAL MOUNTING BRACKETS
0.5
MOUNTING BRACKETS–HORIZONTAL
BRACKET PRE-ASSEMBLY
Repeat Steps 0.1–0.5 to assemble the remaining Horizontal
Mounting Brackets.
Assemble the Z Plate and secure with washer and nut. Do not
tighten until installed on vehicle roof.
0.2
Insert bent bolt
and washer through
mounting bracket
0.1
0.3
Secure mounting assembly
with washer and nut. Do
not tighten until installed on
vehicle roof.
0.4

PRIME DESIGN, A SAFE FLEET BRAND 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪ Phone: [phone] ▪ 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email:[email protected] ▪ www.primedesign.net
TM & © 2015 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6092974, 6764268, 6971563, 2364879, 8857689, 8511525, 8991889 AND OTHER PATENTS PENDING
5
VBR-326 ASSEMBLY INSTRUCTIONS–HORIZONTAL MOUNTING BRACKETS
0.10
MOUNTING BRACKETS–VERTICAL
BRACKET PRE-ASSEMBLY
Repeat Steps 0.6–0.10 to assemble the remaining Vertical
Mounting Brackets.
Assemble the Z Plate and secure with washer and nut. Do not
tighten until installed on vehicle roof.
0.7
Insert bent bolt
and washer through
mounting bracket
0.6
Insert 45MM carriage
bolt through mounting
brace, bracket, and
Z Plate as shown.
0.8
Secure mounting assembly
with washer and nut. Do
not tighten until installed on
vehicle roof.
0.9

PRIME DESIGN, A SAFE FLEET BRAND 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪ Phone: [phone] ▪ 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email:[email protected] ▪ www.primedesign.net
TM & © 2015 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6092974, 6764268, 6971563, 2364879, 8857689, 8511525, 8991889 AND OTHER PATENTS PENDING
6
1
1
4
2
1
3/13
9
5
6
10
7/8
VBR-326 ASSEMBLY INSTRUCTIONS–RIGHT SIDE ROTATION
RIGHT ROTATION
ASSEMBLY SEQUENCE
CROSSBARS REAR DRIVE SHAFT
2.2
Apply Anti-Seize compound to Mounting Bracket bolts.
1.1
1.2
1.3
1.3
1.4 Repeat Steps 1.1–1.3 to install the remaining Mounting
Brackets onto the middle and front Crossbars.
2.1
2.3
Torque to 90 in-lbs.

PRIME DESIGN, A SAFE FLEET BRAND 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪ Phone: [phone] ▪ 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email:[email protected] ▪ www.primedesign.net
TM & © 2015 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6092974, 6764268, 6971563, 2364879, 8857689, 8511525, 8991889 AND OTHER PATENTS PENDING
7
CYLINDER ASSEMBLY
3.2
3.1
CONNECTING BAR FASTENERS
6
CONNECTING BAR
4.1
4.2
FRONT DRIVE SHAFT
5.2
5.3
5.4
Torque to
90 in-lbs.
5.1
VBR-326 ASSEMBLY INSTRUCTIONS–RIGHT SIDE ROTATION

PRIME DESIGN, A SAFE FLEET BRAND 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪ Phone: [phone] ▪ 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email:[email protected] ▪ www.primedesign.net
TM & © 2015 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6092974, 6764268, 6971563, 2364879, 8857689, 8511525, 8991889 AND OTHER PATENTS PENDING
8CROSSBAR SEALING
7
7
L POSTS
8
8
Torque to
90 in-lbs
Torque to 90 in-lbs
Z POSTS
SEE QUICK START GUIDE FOR ADJUSTMENTS
9.1
9.1
Cover the second
Crossbar hole.
Cover the rst
Crossbar hole.
9.2
Torque to 90 in-lbs
Apply Silicone Sealant
to Connecting Bar ends
10.2
10.1
DRIVE SHAFT SEALING
VBR-326 ASSEMBLY INSTRUCTIONS–RIGHT SIDE ROTATION

PRIME DESIGN, A SAFE FLEET BRAND 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪ Phone: [phone] ▪ 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email:[email protected] ▪ www.primedesign.net
TM & © 2015 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6092974, 6764268, 6971563, 2364879, 8857689, 8511525, 8991889 AND OTHER PATENTS PENDING
9
11
11
11
12
12
LEFT BASE ASSEMBLY SEQUENCE
VBR-326 ASSEMBLY INSTRUCTIONS–LEFT SIDE BASE
LADDER STOPS
11.1
11.2 Torque to 90 in-lbs

PRIME DESIGN, A SAFE FLEET BRAND 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪ Phone: [phone] ▪ 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email:[email protected] ▪ www.primedesign.net
TM & © 2015 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6092974, 6764268, 6971563, 2364879, 8857689, 8511525, 8991889 AND OTHER PATENTS PENDING
10
VBR-326 ASSEMBLY INSTRUCTIONS–FINAL ADJUSTMENT
CYLINDER ADJUSTMENT
Adjust the Cylinder Flow
Control Screw to allow
approximately 3 seconds
time for the ladder to glide
down when operating the
loaded Ladder Rack.
13
For additional information regarding your VBR-326 Ladder Rack,
please visit the Prime Design website at: www.primedesign.net.
Using a QR code reader in your smart phone or tablet, read the QR
Code shown below and follow the same steps as you would from your
laptop or computer.
If you’re viewing this document as an interactive PDF, you may simply
click on the QR Code below to access the Prime Design website.
ADDITIONAL INFORMATION
CROSSBAR SEALING
12
12

Page Intentionally Left Blank

USAM-VBR326-US01 Rev-A 0615