Prime Design AR1930 User manual

PRIME DESIGN, A SAFE FLEET BRAND 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪ Phone: [phone] ▪ 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email:[email protected] ▪ www.primedesign.net
TM & © 2015 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6092974, 6764268, 6971563, 2364879, 8857689, 8511525, 8991889 AND OTHER PATENTS PENDING
2
10
8
2
1
9
9
9
5
9
8
8
9
6
3
4
79
9
80” Channels (2X)
60” Channels (2X)
M6 Channel Insert (12X)
M6 Neoprene Washer (24X)
¼” Fender Washer (12X)
M6 Lock Nut (12X)
Brackets (6X)
Top Connector (2X) Bottom Connector (2X)
M8 x 40MM Bolt (4X)
End Caps (4X) Screws (8X)
AR1930 ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS
1—FBM3-0059-A................................................... (Qty 1)
Channels with hardware
CONTENTS OVERVIEW
2—Side Rail Assembly........................................... (Qty 1)
Rear, Right Hand, 84.00”
3—Side Rail Assembly........................................... (Qty 1)
Front, Right Hand, 68.00”
4—Side Rail Connector ......................................... (Qty 1)
Right Hand, 6.00”

PRIME DESIGN, A SAFE FLEET BRAND 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪ Phone: [phone] ▪ 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email:[email protected] ▪ www.primedesign.net
TM & © 2015 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6092974, 6764268, 6971563, 2364879, 8857689, 8511525, 8991889 AND OTHER PATENTS PENDING
3
M8 Cap Head Bolt (14X)
M8 Lock Washer (14X)
M8 Cap Head Bolt (2X)M8 Lock Washer (2X)
M8 Cap Head Bolt (6X)M8 Lock Washer (6X)
Roller Spring (2X)Roller Tube Pin (2X)
Roller End Cap (2X)Roller Holder (2X) M8 Strip Nut (2X)
Roller Tube 55.75” (1X)
AR1930 ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS
9—AluRack Standard Crossbar ............................ (Qty 7)
With hardware, 59.00”
10—Roller Assembly,............................................. (Qty 1)
With hardware, 59.00”
ASZ-0101 (1X)
11—Anti-Seize........................................................ (Qty 1)
8—AluRack Construction Crossbar....................... (Qty 3)
With hardware, 59.00”
5—Side Rail Assembly........................................... (Qty 1)
Rear, Left Hand, 84.00”
6—Side Rail Assembly........................................... (Qty 1)
Front, Left Hand, 68.00”
7—Side Rail Connector ......................................... (Qty 1)
Left Hand, 6.00”

PRIME DESIGN, A SAFE FLEET BRAND 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪ Phone: [phone] ▪ 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email:[email protected] ▪ www.primedesign.net
TM & © 2015 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6092974, 6764268, 6971563, 2364879, 8857689, 8511525, 8991889 AND OTHER PATENTS PENDING
4
AR1930 ASSEMBLY INSTRUCTIONS–FBM MOUNTINGS
Rear
Front
60”
80”
Rear
Front
M6 T Insert
Neoprene Washer (outside)
Neoprene Washer (inside)
¼” Fender Washer
M6 Lock Nut
Right Rear
8.125”
Left Rear
8.125”
Assemble Channel hardware
through roof as shown, but
do not tighten.
0.1
Slide the upper and lower
Channel Connectors into
Channels and align holes
0.2
0.3
Slide Channels onto
Mounting Brackets
0.4
Torque screws to 90 in-lbs
M8 x 40MM Bolt
0.5 Set to specied distances shown below, then torque Mounting
hardware nuts to 80 in-lbs.
FBM3-0059-A
MOUNTING BRACKETS

PRIME DESIGN, A SAFE FLEET BRAND 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪ Phone: [phone] ▪ 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email:[email protected] ▪ www.primedesign.net
TM & © 2015 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6092974, 6764268, 6971563, 2364879, 8857689, 8511525, 8991889 AND OTHER PATENTS PENDING
5
AR1930 ASSEMBLY INSTRUCTIONS–FBM MOUNTINGS
Right Rear
63.00” 59.25”
Set flush to end
Left Rear
63.00”59.25”
Set flush to end
0.6 Loosen bolts
0.7 Set to distances then torque Rear Bracket nuts to 90 in-lbs
leaving Center and Front Brackets loose until Step 6.6

PRIME DESIGN, A SAFE FLEET BRAND 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪ Phone: [phone] ▪ 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email:[email protected] ▪ www.primedesign.net
TM & © 2015 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6092974, 6764268, 6971563, 2364879, 8857689, 8511525, 8991889 AND OTHER PATENTS PENDING
6
84” LH Rear
Rail Connector LH
68” LH Front
5
1/2
4 (STD.)
4 (CON.)
4 (STD.)
4 (STD.)
4 (STD.)
4 (CON.)
1/3
4 (STD.)
4 (CON.)
4 (STD.)
6
4 (STD.)
84” RH Rear
Rail Connector RH
68” RH Front
AR1930 ASSEMBLY INSTRUCTIONS–CROSSBAR INSTALLATION
ALURACK ASSEMBLY SEQUENCE
SIDE RAIL ASSEMBLY
Torque to 80 in-lbs
1.2
1.1 Assemble Side rails as shown

PRIME DESIGN, A SAFE FLEET BRAND 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪ Phone: [phone] ▪ 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email:[email protected] ▪ www.primedesign.net
TM & © 2015 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6092974, 6764268, 6971563, 2364879, 8857689, 8511525, 8991889 AND OTHER PATENTS PENDING
7
AR1930 ASSEMBLY INSTRUCTIONS–CROSSBAR INSTALLATION
RIGHT SIDE RAIL
AND CROSSBARS 3.1
Do not tighten
until Step 4.2
3.2
Crossbar Bolts attach into
pre-installed Strip Nuts
LEFT SIDE RAIL
AND CROSSBARS
Crossbar Bolts attach into
pre-installed Strip Nuts
2.1
Do not tighten
until Step 4.2
2.2

PRIME DESIGN, A SAFE FLEET BRAND 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪ Phone: [phone] ▪ 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email:[email protected] ▪ www.primedesign.net
TM & © 2015 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6092974, 6764268, 6971563, 2364879, 8857689, 8511525, 8991889 AND OTHER PATENTS PENDING
8
151.25”
15.75” 16.00” 15.50”15.75”15.50”
FrontRear
9.75” 16.00”15.75”15.75”15.50”
AR1930 ASSEMBLY INSTRUCTIONS–CROSSBAR ADJUSTMENT
CROSSBAR ADJUSTMENT
4.1
4.2
Torque Bolts
to 90 in-lbs
Adjust Crossbar
distances as
shown below

PRIME DESIGN, A SAFE FLEET BRAND 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪ Phone: [phone] ▪ 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email:[email protected] ▪ www.primedesign.net
TM & © 2015 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6092974, 6764268, 6971563, 2364879, 8857689, 8511525, 8991889 AND OTHER PATENTS PENDING
9
AR1930 ASSEMBLY INSTRUCTIONS–ROLLER ASSEMBLY INSTALLATION
ROLLER ASSEMBLY
5.1
5.2
5.3
Position Roller Assembly
ush to rear then torque
Allen Head bolts to 90 in-lbs

PRIME DESIGN, A SAFE FLEET BRAND 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪ Phone: [phone] ▪ 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email:[email protected] ▪ www.primedesign.net
TM & © 2015 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6092974, 6764268, 6971563, 2364879, 8857689, 8511525, 8991889 AND OTHER PATENTS PENDING
10
AR1930 ASSEMBLY INSTRUCTIONS–RACK TO CHANNELS INSTALLATION
Even
Left Rear Right Rear
Even
MOUNTING RACK TO CHANNELS
6.2
6.4
6.5
Torque to 90 in-lbs
6.1
Loosen nuts on all
Mounting Brackets
6.3
Position Rack until evenly spaced
between Channel Mountings
Channel Mountings
align to Crossbars

PRIME DESIGN, A SAFE FLEET BRAND 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118 ▪ Phone: [phone] ▪ 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email:[email protected] ▪ www.primedesign.net
TM & © 2015 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6092974, 6764268, 6971563, 2364879, 8857689, 8511525, 8991889 AND OTHER PATENTS PENDING
11
AR1930 ASSEMBLY INSTRUCTIONS–RACK TO CHANNELS INSTALLATION
ADDITIONAL INFORMATION
For additional information regarding your AR1930 Ladder Rack, please
visit the Prime Design website at: www.primedesign.net.
Using a QR code reader in your smart phone or tablet, read the QR
Code shown below and follow the same steps as you would from your
laptop or computer.
If you’re viewing this document as an interactive PDF, you may simply
click on the QR Code below to access the Prime Design website.
6.6
Torque to 90 in-lbs

USAM-AR1930-US01 Rev-A 0615