Metra Electronics 95-3023HG User manual

CAUTION! All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 8/13/19 INST95-3023HG
INSTALLATION INSTRUCTIONS
95-3023HG
KIT FEATURES
• ISO DDIN radio provision
• Painted high gloss black
KIT COMPONENTS
• A) Radio trim panel • B) Radio housing • C) Radio brackets • D) (4) #8 x 3/8” Phillips screws • E) (4) Panel clips
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• 9/32” Socket wrench • Cutting tool
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Preparation .......................................................2
Kit Assembly ..........................................................3
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: TBA
Antenna Adapter: 40-EU55
Steering Wheel Control Interface: ASWC-1
A B DC
Chevrolet Trax 2017-up*
*Visit MetraOnline.com for up-to-date vehicle specific applications.
E

1.800.221.0932
|
MetraOnline.com
2
DASH DISASSEMBLY KIT PREPARATION
1. Unclip and remove the dash panel
surrounding the radio. (Figure A)
2. Unclip and remove the radio trim.
(Figure B)
3. Remove (2) 9/32” screws securing
the radio, then pull down and back to
release the radio. Unplug the connectors
to remove the radio. (Figure C)
4. Unclip and slide off the plastic trim piece
on the top of the radio. (Figure D)
5. Remove (2) 9/32” screws securing each a/c
vent, then unclip and remove the vents.
Continue to Kit Preparation
Attention! After the sub-dash has been cut,
the factory radio will no longer be able to
be installed.
1. Cut the sub-dash to allow room for the
aftermarket radio. (Figure A)
2. Attach (4) panel clips provided with the
kit onto the radio trim panel. (Figure B)
Continue to Kit Assembly
(Figure A)
Remove
shaded areas
(Figure B)
(Figure C)
(Figure D)
(Figure B)(Figure A)
“Head On” View

REV. 8/13/2019 INST95-3023HG 3
KIT ASSEMBLY
1. Secure the radio brackets to the radio
using the screws supplied with the
radio. (Figure A)
2. Secure the radio assembly to the radio
housing using the (4) #8 x 3/8” Phillips
screws provided. (Figure B)
3. Attach the plastic trim piece removed in
dash disassembly to the top of the
radio housing.
4. Locate the factory wiring harness and
antenna connector in the dash and
complete all necessary connections to
the radio. Metra recommends using
the proper mating adapter from Metra
and/or Axxess. Test the radio for proper
operation.
(Figure A) (Figure B)
5. Secure the completed radio assembly,
and the a/c vents, to the dash using the
factory screws.
a. Slide the radio assembly into
the dash.
b. Wiggle the a/c vents in.
c. Secure the now complete assembly
to the dash using the (6) factory
9/32” screws.
6. Reassemble the dash in reverse
order of disassembly to complete the
installation, using the 95-3023HG radio
trim panel.

KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
®
Metra recommends MECP
certified technicians
Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 8/13/19 INST95-3023HG
INSTALLATION INSTRUCTIONS
95-3023HG
If you are having difficulties with the installation
of this product, contact our Tech Support line
either by phone at 386-257-1187, or email at
[e-mail]. Before
doing so, look over the instruction booklet a
second time and ensure that the installation was
performed exactly as the instruction booklet
is stated. Have the vehicle apart and ready to
perform troubleshooting steps before contacting
Metra/Axxess Tech Support.