Prime Design FEA-0015 User manual

PRIME DESIGN, A SAFE FLEET BRAND ▪ Address: 1689 Oakdale Avenue #102, West St Paul, Minnesota 55118
Toll Free: 1.8.PRIME.RACK ▪ Fax: [phone] ▪ Email: [email protected] ▪ Website: www.primedesign.net

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪ TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING
2
1
2
3
4
5
5
5
5
FEA-0015 ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS
1—Front Drive Shaft .............................................. (Qty 1)
B Version, 23.75”
CONTENTS OVERVIEW
3—Rear Drive Shaft............................................... (Qty 1)
Right Hand, B4 Version, 46.00”
2—Connecting Bar................................................. (Qty 1)
36.00”
4—Handle Latch Assembly ................................... (Qty 1)
Right Hand

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪ TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING
3
FEA-0015 ASSEMBLY INSTRUCTIONS–PACKAGING CONTENTS
5—HKT-8162.......................................................... (Qty 1)
Modular Rotation Hardware Kit
Anti-Seize (1X)
Lubricant (1X)
Clevis Pin (1X)Cotter Pin (1X)
M8 x 50MM (4X) ⅜" x 2.25" (2X)
1.00" Sealing
Stickers (10X)
M8 Lock Nut (4X) ⅜" Lock Nut (2X) ⅜" Flat Washer (4X)" Flat Washer (8X)

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪ TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING
4
2/7
1
4
5
8
6
3
FEA-0015 ASSEMBLY INSTRUCTIONS–RIGHT DRIVE SHAFT
RIGHT DRIVE SHAFT
ASSEMBLY SEQUENCE
REAR DRIVE SHAFT
1.1
1.2
1.3
Torque to
90 in-lbs
CYLINDER HARDWARE
2.1
2.2
NOTE: Crossbars and RH Rotation feature
are shown for illustrative purposes only.
Crossbars and Rotations are not included
with this Drive Shaft feature, and must be
purchased separately.
NOTE: Flow Control Screw
faces toward vehicle rear
NOTE: Loosen the Cylinder Flow Control Screw (Fig.
C) as needed to allow movement for Steps 2.1-2.2.
When nished with Cylinder Hardware, tighten the
Flow control Screw all the way closed then turn back
open 1½ turn.

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪ TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING
5
Approximate
positioning
Note: To prevent damage to
the Release Latch, do not
rotate the lever beyond the
position shown in Figure A.
Figure A
FEA-0015 ASSEMBLY INSTRUCTIONS–RIGHT DRIVE SHAFT
HANDLE LATCH ASSEMBLY
3.1
Remove and retain
for Step 3.5
3.1
Remove and retain
for Step 3.5
3.2
Remove and retain
for Step 3.4
3.3 As shown in Figure A, lightly pull the Release Latch outward
prior to setting the Latch Assembly onto the Drive Shaft.
3.4 Slide into Handle
Clamp Body
3.7
Torque to 90 in-lbs
3.5 Apply Anti-Seize Compound to the Hardware removed during
Step 3.1, then install Hardware into Handle Clamp Body.
Handle must engage
the Latch as shown.
3.6 Position the Handle Latch Assembly with
the Rotation in its full resting position.
The Handle must engage the Crossbar
Interlock before nal tightening.

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪ TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING
6
A
B
A2
A1
B1
B2
*If using the optional
5’ Connecting Bar
FEA-0015 ASSEMBLY INSTRUCTIONS–RIGHT DRIVE SHAFT
CONNECTING BAR FRONT DRIVE SHAFT
4.1
5.1
5.3
4.2
5.2
CONNECTING BAR VARIATIONS
The 3' Connecting Bar can be adjusted to
t Crossbar spacings of 4'–6'.
The optional 5' Connecting Bar can be
adjusted to t Crossbar spacings of 6'–8'.
Assemble the Connecting Bar to the
Drive Shafts according to your model's
Crossbar spacing.
5.4
Torque to
90 in-lbs

Prime Design Limited Warranty. Seller’s sole and exclusive warranty (and Buyer’s sole and exclusive remedy and Seller’s entire liability for any breach thereof) with respect to the Goods is set forth in the Limited Warranty document available at primedesign.net/warranty-liability
(the “Prime Design Limited Warranty”).
▪ TM & © 2020 PRIME DESIGN. PROTECTED BY ONE OR MORE OF THE FOLLOWING PATENT NO.’s 6427889, 6764268, 6971563, 8991889, 9415726, 9506292, 9481313, 9776476, 9796340, 10470565, 10486608 AND OTHER PATENTS PENDING
7
FEA-0015 ASSEMBLY INSTRUCTIONS–RIGHT DRIVE SHAFT
CONNECTING BAR FASTENERS
6
DRIVE SHAFT SEALING
8.1
8.2
Apply Silicone Sealant
(not supplied) to ends
of Connecting Bar
CYLINDER ADJUSTMENT
Adjust the Cylinder Flow
Control Screw to allow
approximately 3 seconds
time for the ladder to glide
down when operating the
loaded Ladder Rack.
7
NOTE: This completes the right hand assembling of FEA-0015.
For left side Drive Shaft assembly procedures, see FEA-0016
Assembly Manual.
If applicable, refer to your next FEA Assembly Manual.
If completed, refer back to your FBM Assembly Manual, and
resume assembling at Step 3.1.
WARNING: Failure to position the Crossbars as shown in your
FBM Assembly Manual may result in damage to the sliding
door and/or ladder rack.

USAM-FEA0015-US01 Rev-A 0419