Primos Proof Camera Series 63054 User manual

PHOTO MODES
Photo
Video Mode
Records Audio
HD VIDEO
HD TIME LAPSE
All Day Time Lapse
+ Photos
Doc Number
PROOF_001
INSTRUCTION MANUAL
Additional Information on this product and answers to
frequently asked questions can be found at www.primos.com
PLEASE READ CAREFULLY BEFORE USE
© 2015 Primos®Hunting 601-879-9323
!

CLEANING CAMERA: Do not use window or any chemical cleaner to clean any part of the camera. Only use
water dampened cloth and wipe gently.
DO NOT COVER UP PIR LED LIGHT ON THE FRONT OF THE CAMERA HOUSING. This light also detects light
conditions for camera exposure. Use this light to verify PIR sensor activity after installing on tree when camera
is under setup mode.
IMPORTANT
For your protection, please carefully read these warnings, precautions and safety/operating instructions completely
before operating this product. Follow these instructions closely and keep this manual for future reference.
WARNING
To reduce the risk of fire, electrical shock or product damage/failure,
- Do not expose unit with the battery door open to rain, moisture, dripping or splashing. Do not open or close the battery
door with wet hand. Completely wipe off water on unit and door before opening.
- Do not lay product on moist ground or submerge in water (this unit is designed for upright outdoor use).
- DO NOT OPEN CASE HOUSING. UNINSULATED, ‘DANGEROUS VOLTAGE’ WITHIN PRODUCTS ENCLOSURE. DO
NOT REMOVE HOUSING COVER. THERE ARE NO USER - SERVICEABLE PARTS INSIDE, REFER SERVICING TO
PRIMOS®CUSTOMER SERVICE.
- Only use batteries as specified in this user manual and install according to correct polarization. Failure to follow may
result in leaking or exploding batteries, damage to product, fire or personal injury. Do not handle damaged or leaking
batteries.
- Do not expose to extreme heat. Do not leave product and/or batteries exposed in direct sunlight inside a vehicle, or
other contained environment for a long period of time.
- Only use accessories as recommended in this manual
- DO NOT install internal batteries and connect an external rechargeable battery at the same time. Failure to follow this
warning may result in premature battery drain, leaking or exploding batteries, damage to product, fire or personal injury.
Do not handle damaged or leaking batteries. PROOF®CAM Battery Case is designed for use with the 8 AA internal
batteries and is excluded from this warning.
CARE & CAUTION
- Transport and handle with care. Do not strongly shake, bump, hit, drop or otherwise cause impact to the product
– can result in product malfunction or damage to key components. Additionally, damage to the case could result in
imperfections to water-resistant properties.
- Take extra care when handling or using product in places with sand and dust. Sand, dust and foreign substances
exposed to product, especially in extreme proportions, may result in poor speaker quality, damage to the external
jacks or internal components and could cause malfunction of the product. If exposed to any of these elements, please
carefully wipe off completely before continued use.
MODIFICATION WARNING
You are cautioned that any changes or modifications not expressly approved in this manual could void your warranty
of this equipment.

INTRODUCTION
OPERATING TEMPERATURE
- Recommended storage temperature range -10°F to 140°F
- Recommended operating temperature range 20°F to 120°F
WARNING
To avoid possible product damage and/or injury, NEVER INSTALL DIFFERENT TYPES OF BATTERIES in the product at
the same time. Failure to follow may result in leaking or exploding batteries, damage to product, fire or personal injury.
Do not handle damaged or leaking batteries.
QUESTIONS??
Feel free to contact the Primos®Customer Service Team with any comments, questions, problems or return requests.
Call [phone] or e-mail [email protected].
It’s the dawning of a new era
for trail camera users. In order
to move forward we have gone
back. Back to what we hunters
want. Products that simplify our
time in the woods. Products
that are designed without
complications we don’t need. A
trail camera that we can rely on
to capture photos and videos.
If you want the most reliable,
most simple-to-use trail camera
money can buy, with all the
functions that really matter and
none of the extras that don’t,
you will thoroughly enjoy your
new Proof Camera.

IT’S SIMPLE TO USE THIS CAMERA
Slide switches to desired setting.
Then slide to ON.
Install SD memory card.
Slide to setup mode. Then simply set
the date & time.
Install batteries.

IT’S SIMPLE TO USE THIS CAMERA
TABLE OF CONTENTS
BEFORE OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Needed To Operate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Select SD Card Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
CAMERA OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Date & Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Switch Settings [MODE, SETTINGS & DELAY] . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
CAMERA FEATURES & OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Camera Is Ready To Use - Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Auto Camera Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Status Indication Lights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Number of Files Stored on SD Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Battery Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Formatting / Clearing SD Memory Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Viewing/Retrieving Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
USB Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
External Power Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Image Stamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
CAMERA SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
OPERATING TIPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
RECOMMENDED ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
CUSTOMER SERVICE & WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

1
INCLUDED PARTS
1. Proof®Cam – (1)
2. 72” Tree Mounting Strap – (1)
3. Instruction Manual – (1)
NEEDED TO OPERATE
1. Eight (8) “AA” Alkaline or Lithium
2. One or more SD Memory Cards
(Camera will support up to 32GB SD or SDHC Cards)
NOTE: If no SD Card is installed ‘Add SD’ will display on the initial menu screen
3. SD Memory Card Reader or other device to download media
from SD Memory Card to Computer. (Many computers have
SD Memory Card slot built-in)
BEFORE OPERATION

2
SELECT SD CARD SIZE
These charts allow you to see the approximate capacity of 2GB, 4GB, 8GB, 16GB & 32GB
SD Memory Cards. This will help you decide which size SD Cards might be appropriate
based on your desired camera mode.
Proof Cam SD Card Storage Capacity
* Approximation - photo/video sizes are based on individual image details
Mode Resolution Avg. File Size Media Type 2GB 4GB 8GB 16GB 32GB
Photo Hi 3000x4000 1.2 MB Images 1660 3320 6640 13280 26560
Photo Lo 1920x1440 400 KB Images 5000 10000 20000 40000 80000
Video Hi 1280x720HD 13 MB Short Videos (15s) 150 300 600 1200 2400
Video Lo 640x360 3.5 MB Short Videos (15s) 570 1140 2280 4560 9120
Time Lapse 1280x960 200 MB
per Day
All Day Videos
1m Time Lapse
10
Days
20
Days
40
Days
80
Days
160
Days

3
A 3-way power switch is used to select the main operating modes: OFF, SETUP, and ON
View Date or Time
Slide switch to setup and with camera LCD screen ON, push ▲or ▼arrows to display date or
time setting in the camera.
To Change Date or Time
With Date or Time setting on the LCD screen, press OK button to enter edit mode (setting should
start to blink). Use▲ or ▼arrows to change the setting, pressing OK button to save.
NOTE: Time/date will have to be reset if AA batteries die or are removed.
To Change Nightvision Shutter Speed
NS means Nightvision shutter, H means high to reduce motion blur but picture will be darker. L
means low to increase brightness but with more motion blur.
CAMERA OPERATION
SETTING DATE & TIME

4
SWITCH SETTINGS [MODE, SETTINGS & DELAY]
1. MODE SWITCH
Decide Which Capture Mode To Use
Photo
Captures high (HI) or standard (LO) resolution photos with
motion detection. Your camera’s photo capture resolution
can be found in the Camera Specifications chart in the back
of this manual. Photo is the most popular capture mode.
Media Saved: JPEG Photos
Video
Captures high (HI) or standard (LO) resolution video clips with motion detection. Your camera’s
video capture resolution can be found in the Camera Specifications chart in the back of this
manual. Video mode is less popular (night videos drain a lot of power resulting in shorter battery
life). Media Saved: AVI Video Clips
All Day Time Lapse
Captures time lapse photography automatically all day and saves footage in a video file. This
mode has gained popularity for scouting further distances, such as big open areas (food plots,
fields, etc) where you will capture footage automatically whether there is motion or not. However,
with the camera constantly taking pictures all day, the battery life will be limited (see Battery Life
in manual). Media Saved: All Day AVI Videos
All Day Time Lapse Day + Photos
Same as Time Lapse above, but ALSO will simultaneously capture photos (with default photo
setting - see below) during Day or Night when motion is detected. This mode allows the long
range surveillance but also with the convenience of quickly seeing what walking directly in front
of the camera [without having to watch the entire day time lapse video] . However, with the
camera constantly taking pictures all day, the battery life will be limited.
Default Photo Setting: Photo Lo, 3 Burst, Delay according to Delay setting.
Media Saved: All Day AVI Video and JPEG Photos

SWITCH SETTINGS [MODE, SETTINGS & DELAY] CONT.
2. SETTING SWITCH
The sliding switches are color coded to match the SETTINGS with the corresponding MODE setting.
Photo Burst
Number of pictures taken each time motion is detected (triggering event)
Video Length
The length (seconds) of each video clip recorded each time motion is detected (triggering event)
Time Lapse Interval
The pre-set amount of time (minutes) you desire between each time lapse photo. Short intervals
offer more constant surveillance but your AVI video file will be larger. Longer intervals will reduce
the video file size and save battery life.
5

SWITCH SETTINGS [MODE, SETTINGS & DELAY] CONT.
3. DELAY SWITCH
The pre-set amount of time you desire between photo & video recordings. The delay switch
setting also applies to delay between photo recordings in Time Lapse + Photo mode.
CAMERA IS READY TO USE!
AFTER SETTING DATE & TIME and SIMPLY SLIDING SWITCHES TO DESIRED SETTING, MOVE
TO THE POWER SWITCH FROM SETUP TO ON. After front red LED blinks for about 15s, the
camera is active standby mode and will record media according to the switch settings.
6
30
SEC

7
AUTO CAMERA SENSITIVITY (PIR Sensing)
This camera is equipped with auto-adjusting Passive Infrared (PIR) Sensor. There is no need to
worry about adjusting any settings for different climates or situations
CAMERA FEATURES & OPTIONS
THE OFF, ON, AND SETUP MODE
The Proof Cam has three basic operational modes:
 •OFF mode: Power switch in the OFF position.
 •ON mode: Power switch in the ON position (LCD screen is off.)
 •SETUP mode: Power switch at the SETUP position (LCD screen is on.)
OFF MODE
The OFF mode is the safe mode when any action must be taken, e.g., replacing the SD card or batteries, or
transporting the device. You will also use OFF mode if you connect the camera to the computer’s USB port later
to download your photos/videos. And of course, when you are storing or not using the camera, you will switch it
OFF. Please note that even in OFF mode the Proof Camera still consumes power at a very low level. Therefore,
it’s a good idea to take the batteries out of the battery compartment if the camera will not be used for a long time.
ON MODE
Anytime after the batteries and SD card have been inserted, you can switch on the camera. When the power switch
is moved to the top position, the camera will enter into the ON (Live) mode. The motion indicator LED will blink red
for about 15 seconds. This interval allows time for you to close the Proof Cam’s front cover, lock it, and leave the
monitored area. Once in the ON mode, no manual controls are needed. The Proof Cam will take photos or videos
automatically (according to its current slide switch settings) when it is triggered by the PIR sensor’s detection of
activity in the area it covers. You can either move the power switch directly from OFF to ON mode, or stop at the
SETUP position first to change one or more settings, then move the switch to ON after you have finished doing so.
SETUP MODE
In the SETUP mode you can check and change the slide switch settings. Moving the power switch to the SETUP
position will turn on the LCD display, and you will see an information screen that shows how many images have
been taken, and the battery level.
NOTE: Always move the power switch from OFF to SETUP mode. It is possible that the camera could lock up if it is
switched from ON to SETUP mode. If this occurs, simply move the switch to OFF and then push it over to SETUP again.

8
STATUS INDICATION LIGHTS
RED LIGHT ***
(on front of camera)
Lights up when the camera detects motion. After you close
camera door and are standing in front of the camera, visibility of
this light is indication that your camera can sense you.
TIP: Under setup mode, walk in front of the camera and look for the red light
to illuminate when you are detected. You can do this to verify your camera
is pointing in the correct direction.
**NEVER COVER THE RED LED LIGHT. This LED LIGHT also
doubles as the camera’s light sensor, which determines day
or night operation.
NUMBER OF FILES STORED ON SD CARD
The initial main LCD screen displays number of files ‘0000’ stored
on the SD Memory Card and the battery life. For example, ‘0015’
would indicate that any combination of ‘fifteen’ photos, videos
and/or time lapse videos are stored in the memory.

9
BATTERY LIFE
Long battery life is one of the most important requirements for convenient and enjoyable game camera use.
There are several variables that will determine the battery life including type of batteries, temperature outside,
recording settings, frequency of camera activity, etc. Colder temperatures, more advanced settings, night
photos and high photo frequency (low camera delay) will result in shorter battery life. Different brands of
batteries may also perform better than others, so please experiment to find what works best for you. (NOTE:
Capturing video clips and time lapse videos uses more power and will result in shorter battery life then capture
motion detected photos.)
EXAMPLES:
- Camera in standby mode with limited record activity may produce up to 1 year battery life.
- Camera with a lot of day activity in mild climate may produce tens of thousands of photos
on one set of AA batteries.
- Time Lapse 1 minute Interval mode may only result in 15-20 day battery life using 8 AA batteries
and 25-30 day battery life for Time Lapse 2 minute Interval mode.
- Setting the camera for video mode can greatly lower the battery life if videos are captured at
night when iR LEDs are illuminated. If night video capture is required, setting the video length
for 5 or 10 seconds is recommended to maximize battery life.
- Do not mix old and new batteries
- Do not mix battery types-use ALL lithium or ALL alkaline

FORMATTING/CLEANING SD MEMORY CARD
If SD Memory Card has been used in any other devices, we recommend formatting before use
in the Proof Cam. We also recommend reformatting the card every time the card is cleared of
pictures. It only takes a few seconds and can avoid inconvenient corruption and compatibility
issues that can result in loss of game pictures.
Formatting The SD Card Erases All images and Data.
NOTE: Primos recommends formatting all SD media on a computer after
media has been copied to the computer and no longer needed on the SD media.
This removes all corrupted files or data artifacts that can cause potential media recording issues.
To Proceed With Formatting Put Camera In SETUP Mode
1. Hold ▲and ▼arrow buttons together for 2 seconds
2. Format is complete when the display shows photo/video count “0000”
CAUTION: NO WARNING IS DISPLAYED WHEN HOLDING DOWN BOTH ARROW BUTTONS
IN FORMATTING SD CARD PROCESS. THIS DELETES ALL PHOTOS, VIDEOS, AND ANY
OTHER DATA ON THE SD CARD.
10

VIEWING/RETRIEVING MEDIA
Explore the methods for viewing recorded media on your camera
SD Memory Card:
1. Remove SD Memory Card from slot in camera
2. Replace with separate, clean SD Card if you want camera to
continue work.
How To View Images/Videos
1. View images/videos with SD Card directly in computer.
If available you can view images/videos by inserting SD Card
directly in SD memory card reader slot in computer
2. View images/videos with SD Card by attaching external USB
memory card reader to your computer.
If your computer doesn’t have an SD Card reader built in, you can
view images/videos by attaching USB memory card reader to
your computer.
11
SD
SD
SD

12
IMAGE STAMP
Moon Phase Temp TimeDate Day of the Week

CAMERA SPECIFICATIONS
13
Vendor Model #/Style # 63054 63055 63056
Camera Model Primos Proof Cam 01 HD --
10MP Game Camera
Primos Proof Cam 02 HD --
12MP Game Camera
Primos Proof Cam 03 HD --
12MP Game Camera
Shooting modes Photos, Videos, HD Time
Lapse, Time Lapse with PIR
Day & Night Photos
Photos, Videos, HD Time
Lapse, Time Lapse with PIR
Day & Night Photos
Photos, Videos, HD Time
Lapse, Time Lapse with PIR
Day & Night Photos
Image sensor 3.0 MP Color CMOS 3.0 MP Color CMOS 3.0 MP Color CMOS
Photo resolution settings Large(3648x2736),
Small(2048x1536)
Large(4000x3000),
Small(1920x1440)
Large(4000x3000),
Small(1920x1440)
Photo burst settings 1, 2, 3, 4, 5 1, 2, 3, 4, 5 1, 2, 3, 4, 5
Video resolution settings 1280x720HD(30fps),
320x240(30fps)
1280x720HD(30fps),
320x240(30fps)
1280x720HD(30fps),
320x240(30fps)
Video length settings 5s, 10s, 15s, 20s, 30s, 60s 5s, 10s, 15s, 20s, 30s, 60s 5s, 10s, 15s, 20s, 30s, 60s
Sound Recording Video Mode Records Audio Video Mode Records Audio Video Mode Records Audio
Time Lapse Video Resolu-
tion
1280x960 (10fps) 1280x960 (10fps) 1280x960 (10fps)
Time Lapse interval set-
tings
1m, 2m, 5m, 10m, 30m, 60m 1m, 2m, 5m, 10m, 30m, 60m 1m, 2m, 5m, 10m, 30m, 60m
Lens 7.5mm f/3.0 7.5mm f/3.0 7.5mm f/3.0
Field of View 45° 45° 45°
Zoom fixed fixed fixed
ISO sensitivity 100 100 100
Infrared Illumination 36 High-Output IR
Emitters;Up to 70ft
48 High-Output IR
Emitters;Up to 100ft
60 High-Output IR
Emitters;Up to 80ft
PIR Sensor Multi Zone Multi Zone Multi Zone
PIR Sensitivity Auto, 45° Auto, 45° Auto, 45°

14
Vendor Model #/Style # 63054 63055 63056
Trigger Time 0.7 Second 0.4 Second 0.4 Second
Removable Memory up to 32 GB SD Card up to 32 GB SD Card up to 32 GB SD Card
System requirements
(Windows)
Windows 2000, XP, Vista,
Win7 or Win 8; USB port
Windows 2000, XP, Vista,
Win7 or Win 8; USB port
Windows 2000, XP, Vista,
Win7 or Win 8; USB port
System requirements
(Mac)
Mac OS X 10.3 or later;
USB port
Mac OS X 10.3 or later;
USB port
Mac OS X 10.3 or later;
USB port
Display 1.1” Character LCD 1.1" Character LCD 1.1" Character LCD
User Interface Sliding Switches Sliding Switches Sliding Switches
Image Stamp Burst Count, Moon Phase,
Temperature, 12 Hour US
Time (AM/PM), Date, Day of
the Week
Burst Count, Moon Phase,
Temperature, 12 Hour US
Time (AM/PM), Date, Day of
the Week
Burst Count, Moon Phase,
Temperature, 12 Hour US
Time (AM/PM), Date, Day of
the Week
Memory SD Memory up to 32 GB
card size (not included)
SD Memory up to 32 GB
card size (not included)
SD Memory up to 32 GB
card size (not included)
Mounting Adjustable Webbing Strap
with Buckle
Adjustable Webbing Strap
with Buckle
Adjustable Webbing Strap
with Buckle
Power requirements 8xAA Batteries (not
included);12V DC in
8xAA Batteries (not
included);12V DC in
8xAA Batteries (not
included);12V DC in
Standby Current < 0.25 mA (<mAh/Day) < 0.25 mA (<mAh/Day) < 0.25 mA (<mAh/Day)
Power Consumption (12v
Power in)
90mA (+960mA with IR) 90mA (+960mA with IR) 90mA (+1100mA with IR)
Power Consumption “SD Card Slot
USB Jack
12V DC Jack”
"SD Card Slot
USB Jack
12V DC Jack"
"SD Card Slot
USB Jack
12V DC Jack"
Product height (in.) 2.5 2.5 2.5
Product width (in.) 4.25 4.25 4.25
Product length (in.) 5.25 5.25 5.25
Product weight (lb) Approx 1.5lbs Approx 1.5lbs Approx 1.5lbs
Operation / Storage Temps “Storage: -10°F to 140°F
Operation: 20°F to 120°F”
"Storage: -10°F to 140°F
Operation: 20°F to 120°F"
"Storage: -10°F to 140°F
Operation: 20°F to 120°F"
Security Authentication FCC, CE, RoHS FCC, CE, RoHS FCC, CE, RoHS

15
OPERATION TIPS
Learning to use your PROOF®Cam
Visiting www.primos.com and watching our Instructional Video Clips is the ‘easiest way’ to learn
‘how to use’ your PROOF®Camera!
Troubleshooting or Questions
Before calling customer service, visit primos.zendesk.com to find troubleshooting tips, frequently
asked questions and answers, as well as any updates.
Camera Mounting Direction
The red status light illuminates when camera detects motion. To verify your camera is pointing in
the correct direction, you can walk in front of the camera after it is setup and look for the red light
to illuminate when you are detected for 15 seconds during the countdown to live mode. After the
15 seconds, the LED will flash 5x before entering live trigger mode.
Camera Mounting Height
Generally 3ft from ground is normally good height to mount the camera, but depends on type of
game and ground terrain.
Blurry Images
Primos®takes pride in the quality of images captured by the Proof® Cam. However, this is an
outdoor product that will be constantly exposed to different/changing conditions that can affect
the quality level. Blurry images typically result from objects causing interference between the
camera and the intended focal point (game too close, brush, trees, etc). Blurry images may also
be the result of direct sunlight, fog, condensation (dew), water droplets, snow/ice, dirt, dust or
other debris on the camera lens. Carefully cleaning the camera lens window, making sure there
are no scratches and/ or placing the camera in a different location may solve this type of problem.
Blurry Image Quality – Motion
Primos®takes pride in the quality of images captured by the Proof®Cam. Primos has improved the
ANTI-BLUR for this product; however there is currently no way to eliminate the potential of photos
with blur caused by game moving (motion) too quickly. We have optimized the Proof®5Cam to limit
the number of motion blurred images and provide as many clear, quality photos as possible. You
may change night vision shutter speed to H to reduce motion blur.