Prinetti IA1864A User manual

CERAMIC TOWER
FAN HEATER
INSTRUCTION MANUAL
IA1864A
Please read and save all instructions to ensure safe and effective use of this Appliance

02 AFTER SALES SUPPORT AU 1300 777 137 NZ 0800 824 556 [email protected]
Contents
General Information and Safety Instructions 03
Parts List Diagram 06
Getting Started 08
Instructions 09
Cleaning, Care and Maintenance 11
Warranty Information 12

03
General Information and Safety Instructions
Read this manual thoroughly before first use, even if you are familiar with this type of
product. The safety precautions enclosed herein reduce the risk of fire, electric shock
and injury when correctly adhered to. Please keep this user manual in a safe place
along with your purchase receipt and carton for future reference. If applicable, pass
these instructions and packaging on to the next owner of the appliance. Always
follow basic safety precautions and accident prevention measures when using an
electrical product.
1. Before connecting the Prinetti Ceramic Tower Fan Heater®, ensure your outlet
voltage and circuit frequency correspond to the voltage stated on the product
rating label.
2. To protect against the risk of electric shock, do not immerse this Tower Heater,
cord set or plug in water or any other liquid.
3. Do not use an extension cord unless completely necessary with the Tower Heater.
4. If an extension cord is used, please ensure that it has a rating equal or exceeding
the rating of this product.
5. Do not pull or carry by the cord, use the cord as a handle, close a door on the
cord, or pull the cord around sharp edges or corners. Keep the cord away from
heated surfaces.
6. Do not bend or damage the cord.
7. Never force the plug into a power outlet.
8. Always unplug the Tower Heater when not in use. To disconnect from the power
outlet, grip the plug and pull away from the power outlet. Never pull by the cord.
9. The power plug must be removed from the power outlet before cleaning,
servicing, maintenance or moving the Tower Heater.
10. Do not move or lift the Tower Heater while the power cord is still connected to
the power outlet or still on. Always ensure it is switched off and has cooled down
before moving.
11. Do not use the Tower Heater if the plug, cord or the product itself is damaged.
Please contact the After Sales Support Line on 1300 777 137 for further advice.
12. Unless your home is already fitted with a residual current device (safety switch),
we recommend installing an RCD with a rated residual operating current not
exceeding 30mA to provide additional safety protection when using electrical
appliances. See your electrician for professional advice.
13. The Tower Heater is intended for indoor household use only. Do not use it for
commercial purposes.
14. Do not use the Tower Heater for other than its intended use.

04 AFTER SALES SUPPORT AU 1300 777 137 NZ 0800 824 556 [email protected]
General Information and Safety Instructions (cont.)
15. This unit has no user-serviceable parts contained within. Do not attempt to repair,
disassemble or modify the Tower Fan.
16. Improper installation may result in the risk of fire, electric shock or injury to person.
17. The manufacturer is not responsible for any eventual damage caused by
improper or faulty use.
18. The use of attachments not sold or recommended by the manufacturer may
cause fire, electric shock or injury.
19. The Tower Heater is not intended to be operated by means of an external timer or
any type of separate remote control unit.
20. The Tower Heater is not a toy. Supervise young children to ensure they do not play
with this product.
21. The Tower Heater is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the product by a person responsible for their safety.
22. Do not leave the Tower Heater unattended when plugged in. Always switch off
and unplug when you are not using the Tower Heater.
23. Do not leave the Tower Heater operating whilst sleeping.
24. Do not operate or place any part of the Tower Heater on or near any hot surfaces
(such as a gas or electric burner, or a heated oven).
25. Do not place the Tower Heater on or near combustible materials such as curtains
or tablecloths.
26. Do not touch hot surfaces. The temperature of the outer body can get very hot
while the Tower Heater is in operation. Allow the unit to cool down before moving.
27. Never block the openings of the Tower Heater or cover the Tower Heater whilst in
use. Covering the Tower Heater may create a risk of fire.
28. Do not insert foreign objects into the openings of the Tower Heater, doing so may
cause fire or electric shock.
29. Allow for adequate air circulation in the room when operating the Tower Heater.
30. Do not operate the Tower Heater with wet hands.
31. Do not use the Tower Heater in the immediate surroundings of a bath, shower or
swimming pool.
32. Always operate on a dry, level surface.

05
General Information and Safety Instructions (cont.)
33. Do not clean with metal scouring pads. Pieces may break off the pad and touch
the electrical parts, creating a risk of electric shock.
WARNING: If the power cord is damaged, the power cord must be replaced by
the manufacturer, its service agent or similarly qualified persons in order to avoid a
hazard.
WARNING: This product has not been designed for any uses other than those
specified in this booklet.
WARNING: Do not cover the Tower Heater. This may create the risk of fire.

06 AFTER SALES SUPPORT AU 1300 777 137 NZ 0800 824 556 [email protected]
Front of Unit
1. Temperature Display
2. LED Touch Screen Control Panel
3. Base
Back of Unit
4. Carry Handle
5. Back Cover
6. Main Power Switch
Parts List Diagram
1
2
4
6
5
3

07
Parts List Diagram (cont.)
LED Touch Screen Control Panel
1. Power/Standby Button
2. MODE Button
3. SWING Button
4. Timer Button
5. Temperature Control Button
Remote Control
6. Temperature Increase Button
7. Temperature Decrease Button
8. CANCEL Button
9. Power/Standby Button
10. MODE Button
11. SWING Button
12. TIMER Button
1 2 3 4 5
12
15
16
17
17
13
14
6
9
10
11
12
7
8

08 AFTER SALES SUPPORT AU 1300 777 137 NZ 0800 824 556 [email protected]
Before First Use
Please ensure you follow the steps below before using this appliance. We recommend
you keep the original packaging for storing your Tower Heater when not in use.
1. Unpack the product but keep all packaging material until you have made
sure your new Tower Heater is undamaged and in good working order. Plastic
wrapping can be a suffocation hazard for babies and young children so ensure
all packaging material are out of their reach.
2. Remove the twist-tie which is securing the electrical cord. Uncoil the cord and
straighten it to remove any kinks. Do not use the product if these parts are
damaged. In case of damage, phone the After Sales Support Line on 1300 777 137.
CAUTION: Do not touch hot surfaces. The temperature of the outer body can get
very hot while the Tower Heater is in operation. Allow the unit to cool down completely
before cleaning or packing the unit away for storage.
NOTE: You may notice a slight odour being emitted from the Tower Heater during the
initial use. This is normal and odour will cease with continued use.
Getting Started

09
1. Connect the plug into a power outlet and switch on. Press the main power switch on
the back of the Tower Heater to the “I” (ON) position. The Tower Heater will beep, and
the LED touch screen control panel will illuminate to display the room temperature.
2. Press the button on the LED touch screen control panel (or remote control) to
power ON, the Tower Heater will enter fan only mode. The fan will activate but the
Tower Heater will not emit any heat.
3. Once the Tower Heater has been switched on by the main power switch, and the
button on the LED touch screen control panel (or remote control) has been
pressed, use the MODE button to select a heating mode.
Low Heat Mode
Heats at 1000W for low level heating. On this mode the
Tower Heater
will reach the desired temperature slower
as it blows at low heat.
High Heat Mode
Heats at 2000W for high level heating. On this mode the
Tower Heater will reach the desired temperature faster as
it blows at high heat.
4. Press the SWING button on the LED touch screen control panel (or remote control)
to activate the oscillation. With this function the Tower Heater will oscillate side
to side which helps circulate the heat in the room. This function will work in any
mode. Ensure you switch off the oscillation function once you are finished to
return the Tower Heater back to the starting position.
5. Press the timer button on the LED touch screen control panel (or remote control)
to select a time. The timer is setup in 30 minute increments and can be set from
0.5 hours (30 minutes) up to 7.5 hours (7 hours and 30 minutes).
6. Press the temperature control button on the LED touch screen control panel
(or press the temperature increase/decrease buttons on the remote control)
to adjust the temperature setting of the Tower Heater. The temperature settings
range from 18-45˚C.
7. When you are finished using the Tower Heater, press the button on the LED
touch screen control panel (or remote control). The heat will turn off but the fan
will continue to operate until the Tower Heater has cooled down. The LED touch
screen control panel will display the temperature of the Tower Heater until it
returns to room temperature.
8. Once the fan has stopped operating, switch off the main power switch at the
back of the Tower Heater, and unplug the unit from the power outlet.
CAUTION: Never block the openings of the Tower Heater or cover the Tower Heater
whilst in use. Covering the Tower Heater may create a risk of fire.
Instructions

10 AFTER SALES SUPPORT AU 1300 777 137 NZ 0800 824 556 [email protected]
Instructions (cont.)
Remote Control Operation
To use the remote control, make sure the Tower Heater is plugged into a power outlet
and the main power switch on the back of the unit is switched to the ON position (“I”).
The remote has an additional ‘CANCEL’ feature included. Press the CANCEL button on
the remote control to cancel any temperature setting and exit the temperature setting
modes, the other modes will remain unchanged and the temperature indicator light
will turn off. The Tower Heater will then default to display the room temperature on the
LED touch screen control panel.
Switch the Tower Heater off using the main power switch at the back of the Tower
Heater when you are finished using the Tower Heater.
Each time you press a button on the remote control, the remote sensor on the Tower
Heater will pick it up and the Tower Heater will beep to acknowledge the selection.
Battery Replacement
If the batteries in the remote control need to be replaced, slide down the battery
cover located on the back of the remote control. Check the inside of the remote
control battery chamber for the polarity symbols, then insert the replacement 2 x AAA
batteries.
NOTE: For the remote control to operate correctly, the remote control must be in
line of sight of the remote sensing window on the LED touch screen. There will be no
change in the function of the unit if the remote control handset is not in line of sight
of the unit, or if there are any obstacles between the remote control and the remote
sensing window.
Safety Thermal Cut-Out
The Tower Heater has an overheat protection system that shuts off the Tower Heater in
the event of overheating.
Should the Tower Heater stop working, turn it off and inspect the air inlets and outlets
for blockages. Wait for the Tower Heater to cool and for the protection system to reset
before attempting to restart the Tower Heater (this may take around 10 minutes).
Tip-Over Switch
The Tower Heater has a safety tip-over switch built-in that switches the Tower Heater off
automatically if the appliance is ever knocked over.
If this occurs, it is highly recommended to manually switch off the appliance before
standing the Tower Heater upright again. Ensure that the Tower Heater is placed on a
flat, level surface before turning it on again.

11
1. The exterior of the Tower Heater can be cleaned by wiping over it with a soft
damp cloth.
2. Always dry thoroughly with a soft dry cloth after cleaning.
3. Use a vacuum cleaner with a soft brush attachment to remove dust and dirt from
air openings.
4. Do not use abrasive cleaners or furniture polish as this can damage the surface
finish.
5. Ensure that the Tower Heater has dried completely before turning it back ON.
CAUTION: Always unplug the Tower Heater when cleaning or assembling.
WARNING: Do not use metal scouring pads to clean the Tower Heater, pieces may
break off the pad and touch the electrical parts of the Tower Heater, creating risk of
electric shock.
NOTE: Always ensure the Tower Heater is switched off and unplugged when not in
use. The unit should have completely cooled down before cleaning.
NOTE: Do not use harsh or abrasive cleaners to clean the Tower Heater, as this
could cause damage the finish of the appliance.
WARNING: Never immerse the Tower Heater, cord or plug into water or any liquid
when cleaning.
NOTE: As a result of continual improvements, the design and specifications of the
product within may differ slightly to the unit illustrated on the packaging.
Storage
1. Before packing away the Tower Heater for storage, ensure it is clean and dry.
2. We recommend storing the Tower Heater in its original carton to protect it from dust.
3. Store the Tower Heater in a clean and dry place, out of children’s reach.
4. Do not place heavy objects on top during storage
Cleaning, Care and Maintenance

12 AFTER SALES SUPPORT AU 1300 777 137 NZ 0800 824 556 [email protected]
Warranty Information
Congratulations on your purchase
This Prinetti®Ceramic Tower Fan Heater is warranted to be free from defects in
material and workmanship under normal use and service conditions for a period of 12
months from the date of purchase of this article. Evidence of unfair usage or incorrect
adjustment by the owner will void this promise. Defects that occur within this warranty
period, under normal use and care, will be repaired, replaced or refunded at our
discretion.
The benefits conferred by this manufacturer’s warranty are in addition to all other
rights and remedies in respect of the product which the consumer has under the
Australian Consumer Law.
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and
for compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.
Conditions of Warranty
All warranty coverage extends only to the original retail purchaser from the date of
purchase. Please keep your receipt, tax invoice or other proof of purchase.
This warranty does not extend to any damage to a product caused by abuse,
improper or abnormal usage, or repairs not provided by us or our Service Centre.
Nor does this warranty extend to products used for commercial or rental purposes.
This warranty does not cover ordinary wear, tear and weathering, failure to follow
directions, improper installation, improper maintenance or acts of God (such as
damage caused by storms, lightning, heavy winds and by snow or ice).
Making A Warranty Claim
In order to make a claim under this warranty please direct your enquiries to our
Service Centre. You can contact them on our 1300 777 137 Phone Number from
Australia or 0800 824 556 Phone Number from New Zealand or send mail to them at:
Uncle Bill’s Service Centre:
2/24 Anderson Road, Smeaton Grange, NSW 2567 – if mailing please include your
contact details.
A service representative will then assist you in the appropriate action to be taken.
For efficient processing of your enquiry please have proof of purchase, the date of
purchase and the retailer name you purchased the item from, and the brand on the
product. Photos of the product, and scans of receipts, may be requested to assist with
your claim.

13
The service centre representative will assess the claim. If:
1. There is a minor fault, they can offer either a replacement spare part,
replacement unit, repair or other suitable remedy.
2. There is a major fault, they can offer a replacement, repair or suggest you return
to the store you purchased it from for a full refund.
NOTE: A request for compensation will need documentary evidence of the loss
or damage suffered. It will also need to be evidenced that such a loss was a
reasonably foreseeable result of a failure by Uncle Bill’s to comply with a consumer
guarantee under the Australian Consumer Law.
3. The product was damaged through abnormal use, no refund or repair can be
offered.
If the product needs to be returned and all the warranty criteria has been met, the
consumer is to return the product to the place of purchase (along with their proof of
purchase) and all costs involved with this will be the responsibility of the consumer.
Our sales and service centre has been set up to provide assembly assistance,
technical support, replacement parts and accessories, and to efficiently handle all
warranty related matters. Please note upon receiving your warranty claim our Service
Centre will send, via post or email, a repair and refurbished goods or parts notice.
If you require an alternative format of this instruction manual such as website, DVD or
by email please contact service@unclebills.com.au to obtain a copy.
SERVICE CENTRE
Contact details and hours of operation.
Phone: 1300 777 137
Email: service@unclebills.com.au
9:00am – 4:30pm (AEST) Monday to Friday (excluding Public Holidays)
9:00am – 3:00pm (AEST) Saturday
This product is warranted and imported by:
Uncle Bill’s (Australia) Pty Ltd
48B Egerton Street
Silverwater NSW 2128, Australia
Phone: 02 8799 3500
Item: IA1864A
Warranty Information (cont.)

Table of contents
Other Prinetti Heater manuals
Popular Heater manuals by other brands

Hastings
Hastings AEROFLO AFX Series Installation and service manual

Webasto
Webasto Air Top 2000 ST B installation instructions

Kampmann
Kampmann Katherm HK Assembly and installation instructions

EQUATION
EQUATION DE20D Assembly, Use, Maintenance Manual

Fondital
Fondital eCool ED 300 W Installation, use and maintenance manual

Levante
Levante LEVQ20 Operation manual